MAX6957 4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and 28

MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
General Description
The MAX6957 compact, serial-interfaced LED display
driver general-purpose I/O (GPIO) peripheral provides
microprocessors with up to 28 ports. Each port is individually user configurable to either a logic input, logic
output, or common-anode (CA) LED constant-current
segment driver. Each port configured as an LED segment driver behaves as a digitally controlled constantcurrent sink, with 16 equal current steps from 1.5mA to
24mA. The LED drivers are suitable for both discrete
LEDs and CA numeric and alphanumeric LED digits.
Each port configured as a GPIO can be either a pushpull logic output capable of sinking 10mA and sourcing
4.5mA, or a Schmitt logic input with optional internal
pullup. Seven ports feature configurable transition
detection logic, which generates an interrupt upon
change of port logic level. The MAX6957 is controlled
through an SPI-compatible 4-wire serial interface.
Features
●● H
igh-Speed 26MHz SPI-/QSPI™-/MICROWIRE®Compatible Serial Interface
●● 2.5V to 5.5V Operation
●● -40°C to +125°C Temperature Range
●● 20 or 28 I/O Ports, Each Configurable as
Constant-Current LED Driver
Push-Pull Logic Output
Schmitt Logic Input
Schmitt Logic Input with Internal Pullup
●● 11µA (max) Shutdown Current
●● 16-Step Individually Programmable Current Control
for Each LED
●● Logic Transition Detection for Seven I/O Ports
Ordering Information
PINPACKAGE
The MAX6957AAX and MAX6957ATL have 28 ports and
are available in 36-pin SSOP and 40-pin TQFN (6mm x
6mm) packages, respectively. The MAX6957AAI and
MAX6957ANI have 20 ports and are available in 28-pin
SSOP and 28-pin DIP packages, respectively.
PART
TEMP RANGE
MAX6957ANI
-40°C to +125°C
28 DIP
MAX6957AAI
-40°C to +125°C
28 SSOP
For a 2-wire interfaced version, refer to the MAX6956
data sheet.
MAX6957AAX
-40°C to +125°C
36 SSOP
MAX6957ATL
-40°C to +125°C
40 TQFN-EP*
For a lower cost pin-compatible port expander without
the constant-current LED drive capability, refer to the
MAX7301 data sheet.
Applications
●●
●●
●●
●●
●●
●●
Set-Top Boxes
Panel Meters
White Goods
Bar Graph Displays
Industrial Controllers
System Monitoring
*Exposed pad.
Pin Configurations
TOP VIEW
ISET 1
28 V+
GND 2
27 CS
GND 3
26 DIN
25 SCLK
DOUT 4
24 P31
P12 5
23 P30
P13 6
P14 7
MAX6957
22 P29
P15 8
21 P28
P16 9
20 P27
P17 10
19 P26
P18 11
18 P25
Typical operating Circuit appears at end of data sheet.
P19 12
17 P24
P20 13
16 P23
QSPI is a trademark of Motorola, Inc.
P21 14
MICROWIRE is a registered trademark of National
Semiconductor Corp.
19-2429; Rev 5; 7/14
15 P22
SSOP/DIP
Pin Configurations continued at end of data sheet.
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Absolute Maximum Ratings
Voltage (with Respect to GND)
V+.............................................................................-0.3V to +6V
All Other pins................................................-0.3V to (V+ + 0.3V)
P4–P31 Current ...............................................................±30mA
GND Current.....................................................................800mA
Continuous Power Dissipation (TA = +70°C)
28-Pin PDIP (derate 14.3mW/°C above +70°C)........ 1143mW
28-Pin SSOP (derate 9.1mW/°C above +70°C)...........727mW
36-Pin SSOP (derate 11.8mW/°C above +70°C).........941mW
40-Pin TQFN (derate 37.0mW/°C above +70°C).......2963mW
Operating Temperature Range (TMIN, TMAX)..... -40°C to +125°C
Junction Temperature.......................................................+150°C
Storage Temperature Range............................. -65°C to +150°C
Lead Temperature (soldering, 10s).................................. +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(Typical Operating Circuit, V+ = 2.5V to 5.5V, TA = TMIN to TMAX, unless otherwise noted.) (Note 1)
PARAMETER
Operating Supply Voltage
Shutdown Supply Current
Operating Supply Current
Operating Supply Current
Operating Supply Current
SYMBOL
CONDITIONS
V+
ISHDN
TYP
2.5
All digital inputs at
V+ or GND
TA = +25°C
MAX UNITS
5.5
5.5
10
TA = TMIN to TMAX
11
TA = +25°C
TA = +25°C
IGPOL
All ports programmed
As outputs low, no load,
All other inputs at V+ or
GND
TA = +25°C
ILED
All ports programmed
as LED outputs, all LEDs
off, no load, all other
inputs at V+ or GND
180
250
TA = TMIN to TMAX
270
µA
210
TA = -40°C to +85°C
230
TA = TMIN to TMAX
240
110
µA
230
TA = -40°C to +85°C
170
V
8
TA = -40°C to +85°C
All ports programmed
As outputs high, no load,
All other inputs at V+ or
GND
IGPOH
MIN
µA
135
TA = -40°C to +85°C
140
TA = TMIN to TMAX
145
µA
INPUTS AND OUTPUTS
Logic-High Input Voltage
Port Inputs
VIH
Logic-Low Input Voltage
Port Inputs
VIL
Input Leakage Current
IIH, IIL
GPIO Input Internal Pullup to V+
IPU
Hysteresis Voltage GPIO Inputs
DVI
Output High Voltage
www.maximintegrated.com
VOH
0.7 ×
V+
GPIO inputs without pullup,
VPORT = V+ to GND
-100
V
±1
0.3 ×
V+
V
+100
nA
V+ = 2.5V
12
19
30
V+ = 5.5V
80
120
180
0.3
µA
V
GPIO outputs, ISOURCE = 2mA, TA = -40°C to
+85°C
V+ 0.7
V
GPIO outputs, ISOURCE = 1mA,
TA = TMIN to TMAX (Note 2)
V+ 0.7
V
Maxim Integrated │ 2
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Electrical Characteristics (continued)
(Typical Operating Circuit, V+ = 2.5V to 5.5V, TA = TMIN to TMAX, unless otherwise noted.) (Note 1)
PARAMETER
Port Sink Current
Output Short-Circuit Current
Port Drive LED Sink Current,
Port Configured as LED Driver
Port Drive Logic Sink Current,
Port Configured as LED Driver
SYMBOL
IOL
IPORT
IPORT_SC
∆IPORT
Input High-Voltage SCLK, DIN,
CS
VIH
Input Low-Voltage SCLK, DIN, CS
VIL
MIN
TYP
2
10
18
mA
Port configured output low, shorted to V+
2.75
11
20
mA
V+ = 2.5V, VLED = 2.3V at maximum LED
current
9.5
13.5
18
V+ = 3.3V, VLED = 2.4V at maximum LED
current (Note 2)
18.5
24
27.5
V+ = 5.5V, VLED = 2.4V at maximum LED
current
19
25
30
V+ = 2.5V, VOUT = 0.6V at maximum LED
current
18.5
23
28.0
V+ = 5.5V, VOUT = 0.6V at maximum LED
current
19
24
28
VPORT = 0.6V
IOLSC
Port LED Sink Current Matching
Input Leakage Current SCLK,
DIN, CS
CONDITIONS
MAX UNITS
mA
6
V+ ≤ 3.3V
1.6
V+ > 3.3V
2
IIH, IIL
-50
Output High-Voltage DOUT
VOH
ISOURCE = 1.6mA
Output Low-Voltage DOUT
VOL
ISINK = 1.6mA
mA
%
V
0.6
V
+50
nA
V+ 0.5
V
0.4
V
Timing Characteristics (Figure 3)
3(V+ = 2.5V to 5.5V, TA = TMIN to TMAX, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
CLK Clock Period
tCP
38.4
ns
CLK Pulse Width High
tCH
19
ns
CLK Pulse Width Low
tCL
19
ns
CS Fall to SCLK Rise Setup Time
tCSS
9.5
ns
CLK Rise to CS Rise Hold Time
tCSH
0
ns
DIN Setup Time
tDS
9.5
ns
DIN Hold Time
tDH
0
ns
Output Data Propagation Delay
Minimum CS Pulse High
tDO
tCSW
CLOAD = 25pF
21
19
ns
ns
Note 1: All parameters tested at TA = +25°C. Specifications over temperature are guaranteed by design.
Note 2: Guaranteed by design.
www.maximintegrated.com
Maxim Integrated │ 3
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Typical Operating Characteristics
(RISET = 39kΩ, TA = +25°C, unless otherwise noted.)
7
0.16
0.12
V+ = 3.3V
6
5
V+ = 2.5V
4
0.08
ALL PORTS LED (OFF)
-40.0
-12.5
15.0
42.5
70.0
97.5
3
125.0
-40.0
-12.5
27
MAX6957 toc04
20
LED DROP = 2.4V
18
16
LED DROP = 1.8V
14
12
10
3.0
3.5
4.0
4.5
5.0
V+ = 5.5V
23
V+ = 3.3V
22
8
V+ = 5.5V
7
PULLUP CURRENT (A)
VPORT = 1.4V
V+ = 3.3V
6
5
V+ = 2.5V
4
0.1
-40.0
-12.5
15.0
18
16
15.0
42.5
70.0
TEMPERATURE (°C)
www.maximintegrated.com
97.5
125.0
42.5
70.0
97.5
3.5
4.0
4.5
5.0
5.5
GPO SINK CURRENT vs. TEMPERATURE
(OUTPUT = 0)
V+ = 2.5V TO 5.5V, VPORT = 0.6V
12
10
8
6
2
125.0
-12.5
15.0
42.5
70.0
97.5
GPI PULLUP CURRENT
vs. TEMPERATURE
GPO SHORT-CIRCUIT CURRENT
vs. TEMPERATURE
100
V+ = 3.3V
-40.0
-40.0
TEMPERATURE (°C)
V+ = 5.5V
10
3.0
14
100
-12.5
15.0
42.5
70.0
TEMPERATURE (°C)
125.0
GPO = 0, PORT
SHORTED TO V+
10
V+ = 2.5V
-12.5
2.5
TEMPERATURE (°C)
3
-40.0
2.0
4
1000
MAX6957 toc07
PORT SOURCE CURRENT (mA)
VLED = 2.4V
24
20
5.5
ALL PORTS OUTPUT (0)
V+ (V)
PORT CURRENT (mA)
2.5
1
0.01
125.0
MAX6957 toc08
2.0
GPO SOURCE CURRENT vs. TEMPERATURE
(OUTPUT = 1)
2
97.5
25
V+ (V)
9
70.0
21
8
6
42.5
26
PORT SINK CURRENT (mA)
PORT SINK CURRENT (mA)
22
15.0
LED DRIVER SINK CURRENT
vs. TEMPERATURE
LED DRIVER SINK CURRENT vs. V+
24
ALL PORTS OUTPUT (1)
TEMPERATURE (°C)
TEMPERATURE (°C)
26
10
ALL PORTS LED (OFF)
MAX6957 toc05
0.04
0
ALL PORTS LED (ON)
MAX6957 toc06
0.20
OPERATING SUPPLY CURRENT vs. V+
(NO LOADS)
MAX6957 toc09
0.24
V+ = 5.5V
SUPPLY CURRENT (mA)
ALL PORTS
OUTPUT (0)
ALL PORTS
OUTPUT (1)
SUPPLY CURRENT (A)
0.28
100
PORT SINK CURRENT (mA)
0.32
8
MAX6957 toc02
V+ = 2.5V TO 5.5V
NO LOAD
0.36
SUPPLY CURRENT (mA)
MAX6957 toc01
0.40
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
MAX6957 toc03
OPERATING SUPPLY CURRENT
vs. TEMPERATURE
GPO = 1, PORT
SHORTED TO GND
97.5
125.0
1
-40.0
-12.5
15.0
42.5
70.0
97.5
125.0
TEMPERATURE (°C)
Maxim Integrated │ 4
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Pin Description
PIN
NAME
28 SSOP
36 SSOP 40 TQFN
28 PDIP
FUNCTION
1
1
36
ISET
Segment Current Setting. Connect ISET to GND through a resistor (RISET) to set
the maximum segment current.
2, 3
2, 3
37, 38,
39
GND
Ground
4
4
40
DOUT
5–24
—
—
P12–P31
LED Segment Drivers and GPIO. P12 to P31 can be configured as CA LED drivers,
GPIO outputs, CMOS logic inputs, or CMOS logic inputs with weak pullup resistor.
—
5–32
1–10,
12–19,
21–30
P4–P31
LED Segment Drivers and GPIO. P4 to P31 can be configured as CA LED drivers,
GPIO outputs, CMOS logic inputs, or CMOS logic inputs with weak pullup resistor.
25
33
32
SCLK
4-Wire Serial Clock Input Port
4-Wire Serial Data Output Port
26
34
33
DIN
4-Wire Serial Data Input Port
27
35
34
CS
4-Wire Chip-Select Input, Active-Low
28
36
35
V+
Positive Supply Voltage. Bypass V+ to GND with a minimum 0.047µF capacitor.
—
—
11, 20,
31
N.C.
—
—
EP
EP
No Connection. Not internally connected.
Exposed Pad. Internally connected to GND. Connect to large ground plane for
maximum thermal dissipation. Do not use as sole ground connection.
Detailed Description
The MAX6957 LED driver/GPIO peripheral provides up
to 28 I/O ports, P4 to P31, controlled through an SPIcompatible serial interface. The ports can be configured
to any combination of constant-current LED drivers, logic
inputs and logic outputs, and default to logic inputs on
power-up. When fully configured as an LED driver, the
MAX6957 controls up to 28 LED segments with individual
16-step adjustment of the constant current through each
LED segment. A single resistor sets the maximum segment current for all segments, with a maximum of 24mA
per segment. The MAX6957 drives any combination of
discrete LEDs and CA digits, including seven-segment
and starburst alphanumeric types.
Figure 1 is the MAX6957 functional diagram. Any I/O
port can be configured as a push-pull output (sinking 10mA, sourcing 4.5mA), or a Schmitt-trigger logic
input. Each input has an individually selectable internal
pullup resistor. Additionally, transition detection allows
seven ports (P24 through P30) to be monitored in any
maskable combination for changes in their logic status.
www.maximintegrated.com
A detected transition is flagged through an interrupt pin
(port P31).
The Typical Operating Circuit shows two MAX6957s
working together controlling three monocolor 16-segment-plus-DP displays, with five ports left available for
GPIO (P27–P31 of U2).
The port configuration registers set the 28 ports, P4 to
P31, individually as either LED drivers or GPIO. A pair
of bits in registers 0x09 through 0x0F sets each port’s
configuration (Tables 1 and 2).
The 36-pin MAX6957AAX has 28 ports, P4 to P31. The
28-pin MAX6957ANI and MAX6957AAI make only 20
ports available. The eight unused ports should be configured as outputs on power-up by writing 0x55 to registers 0x09 and 0x0A. If this is not done, the eight
unused ports remain as floating inputs and quiescent
supply current rises, although there is no damage to
the part.
Maxim Integrated │ 5
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 1. Port Configuration Map
REGISTER DATA
ADDRESS
CODE (HEX)
REGISTER
D7
D6
D5
D4
D3
D2
D1
D0
Port Configuration for P7, P6, P5, P4
0x09
P7
P6
P5
P4
Port Configuration for P11, P10, P9, P8
0x0A
P11
P10
P9
P8
Port Configuration for P15, P14, P13, P12
0x0B
P15
P14
P13
P12
Port Configuration for P19, P18, P17, P16
0x0C
P19
P18
P17
P16
Port Configuration for P23, P22, P21, P20
0x0D
P23
P22
P21
P20
Port Configuration for P27, P26, P25, P24
0x0E
P27
P26
P25
P24
Port Configuration for P31, P30, P29, P28
0x0F
P31
P30
P29
P28
Table 2. Port Configuration Matrix
MODE
FUNCTION
Output
LED Segment Driver
Output
GPIO Output
Input
GPIO Input
Without Pullup
Input
GPIO Input with Pullup
PORT
REGISTER
(0x20–0x5F)
(0xA0–0xDF)
PIN BEHAVIOR
LOWER
0x09 to 0x0F
0
0
0x09 to 0x0F
0
1
Schmitt logic input
0x09 to 0x0F
1
0
Schmitt logic input with pullup
0x09 to 0x0F
1
1
High impedance
Register bit = 1
Open-drain current sink, with sink
current (up to 24mA) determined
by the appropriate current register
Register bit =
input logic level
PORT
CONFIGURATION
BIT PAIR
UPPER
Register bit = 0
Register bit = 0
ADDRESS
CODE (HEX)
Active-low logic output
Active-high logic output
Note: The logic is inverted between the two output modes; a high makes the output go low in LED segment driver mode (0x00) to
turn that segment on; in GPIO output mode (0x01), a high makes the output go high.
Register Control of I/O Ports and LEDs
Across Multiple Drivers
The MAX6957 offers 20 or 28 I/O ports, depending
on package choice. These can be applied to a variety
of combinations of different display types, for example: seven, 7-segment digits (Figure 2). This example
requires two MAX6957s, with one digit being driven by
both devices, half by one MAX6957, half by the other
(digit 4 in this example). The two drivers are static,
and therefore do not need to be synchronized. The
MAX6957 sees CA digits as multiple discrete LEDs. To
simplify access to displays that overlap two MAX6957s,
the MAX6957 provides four virtual ports P0 through P3.
To update an overlapping digit, send the same code
twice as an eight-port write, once to P28 through P35 of
the first driver, and again to P0 through P7 of the sec-
www.maximintegrated.com
ond driver. The first driver ignores the last 4 bits and the
second driver ignores the first 4 bits.
Two addressing methods are available. Any single
port (bit) can be written (set/cleared) at once; or, any
sequence of eight ports can be written (set/cleared) in
any combination at once. There are no boundaries; it is
equally acceptable to write P0 through P7, P1 through
P8, or P31 through P38 (P32 through P38 are nonexistent, so the instructions to these bits are ignored).
Using 8-bit control, a seven-segment digit with a decimal
point can be updated in a single byte-write, a 14-segment
digit with DP can be updated in two byte-writes, and
16-segment digits with DP can be updated in two bytewrites plus a bit write. Also, discrete LEDs and GPIO port
bits can be lit and controlled individually without affecting
other ports.
Maxim Integrated │ 6
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
INTENSITY REGISTERS
INTENSITY
TEST REGISTER
TEST
PORT REGISTERS
CONFIGURATION
MASK REGISTER
P4 TO P31
LED DRIVERS
OR GPIO
LED DRIVERS AND GPIO
CONFIGURATION
REGISTERS
PORT CHANGE
DETECTOR
DATA
CE
R/W
8
SEGMENT OR
GPIO DATA
R/W
8
COMMAND
REGISTER DECODE
8
8
DATA BYTE
COMMAND BYTE
CS
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
DIN
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
DOUT
SCLK
Figure 1. MAX6957 Functional Diagram
Shutdown
When the MAX6957 is in shutdown mode, all ports are
forced to inputs, and the pullup current sources are turned
off. Data in the port and control registers remain unaltered
so port configuration and output levels are restored when
the MAX6957 is taken out of shutdown. The display driver can still be programmed while in shutdown mode. For
minimum supply current in shutdown mode, logic inputs
should be at GND or V+ potential. Shutdown mode is
exited by setting the S bit in the configuration register
(Table 6). Shutdown mode is temporarily overridden by
the display test function.
Serial Interface
The MAX6957 communicates through an SPI-compatible 4-wire serial interface. The interface has three
inputs, Clock (SCLK), Chip Select (CS), and Data In
(DIN), and one output, Data Out (DOUT). CS must be
www.maximintegrated.com
low to clock data into or out of the device, and DIN
must be stable when sampled on the rising edge of
SCLK. DOUT provides a copy of the bit that was input
15.5 clocks earlier, or upon a query it outputs internal
register data, and is stable on the rising edge of SCLK.
Note that the SPI protocol expects DOUT to be high
impedance when the MAX6957 is not being
accessed; DOUT on the MAX6957 is never high impedance. Go to www.maximintegrated.com/an1879 for
ways to convert DOUT to tri-state, if required.
SCLK and DIN may be used to transmit data to other
peripherals, so the MAX6957 ignores all activity on
SCLK and DIN except between the fall and subsequent
rise of CS.
Maxim Integrated │ 7
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
7-SEGMENT DIGIT 1
7-SEGMENT DIGIT 2
7-SEGMENT DIGIT 3
7-SEGMENT DIGIT 4
V+
VIRTUAL SEGMENTS
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31
7-SEGMENT DIGIT 5
7-SEGMENT DIGIT 6
7-SEGMENT DIGIT 7
V+
VIRTUAL SEGMENTS
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31
Figure 2. Two MAX6957s Controlling Seven 7-Segment Displays
CS
tCSH
tCSS
tCL
tCH
tCSH
SCLK
tDS
tDH
DIN
tDV
tDO
DOUT
Figure 3. 4-Wire Interface Timing
www.maximintegrated.com
Maxim Integrated │ 8
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
MICROCONTROLLER
SERIAL DATA INPUT
SERIAL CS OUTPUT
CS
CS
MAX6957
SCLK
SCLK
SERIAL CLOCK OUTPUT
DOUT
DIN
SERIAL DATA OUTPUT
CS
MAX6957
MAX6957
SCLK
DIN
DOUT
DIN
DOUT
Figure 4. Daisy-Chain Arrangement for Controlling Multiple MAX6957s
CS
SCLK
DIN
D15
=0
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
DOUT
D15 = 0
.
Figure 5. 16-Bit Write Transmission to the MAX6957
Control and Operation Using the
4-Wire Interface
Controlling the MAX6957 requires sending a 16-bit word.
The first byte, D15 through D8, is the command address
(Table 3), and the second byte, D7 through D0, is the data
byte (Table 4).
Connecting Multiple MAX6957s
to the 4-Wire Bus
Multiple MAX6957s may be daisy-chained by connecting the DOUT of one device to the DIN of the next, and
driving SCLK and CS lines in parallel (Figure 4). Data at
DIN propagates through the internal shift registers and
appears at DOUT 15.5 clock cycles later, clocked out on
the falling edge of SCLK. When sending commands to
multiple MAX6957s, all devices are accessed at the same
time. An access requires (16 × n) clock cycles, where n is
the number of MAX6957s connected together. To update
just one device in a daisy-chain, the user can send the
No-Op command (0x00) to the others.
www.maximintegrated.com
Writing Device Registers
The MAX6957 contains a 16-bit shift register into which
DIN data are clocked on the rising edge of SCLK, when
CS is low. When CS is high, transitions on SCLK have no
effect. When CS goes high, the 16 bits in the Shift register
are parallel loaded into a 16-bit latch. The 16 bits in the
latch are then decoded and executed.
The MAX6957 is written to using the following sequence:
1) Take SCLK low.
2)Take CS low. This enables the internal 16-bit shift
register.
3) Clock 16 bits of data into DIN—D15 first, D0 last—
observing the setup and hold times (bit D15 is low,
indicating a write command).
4)Take CS high (either while SCLK is still high after
clocking in the last data bit, or after taking SCLK low).
5) Take SCLK low (if not already low).
Figure 5 shows a write operation when 16 bits are
transmitted.
Maxim Integrated │ 9
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
It is acceptable to clock more than 16 bits into the
MAX6957 between taking CS low and taking CS high
again. In this case, only the last 16 bits clocked into the
MAX6957 are retained.
active-high interrupt output (INT). Note that the MAX6957
does not identify which specific port(s) caused the interrupt, but provides an alert that one or more port levels
have changed.
Reading Device Registers
The mask register contains 7 mask bits that select which
of the seven ports P24–P30 are to be monitored (Table
13). Set the appropriate mask bit to enable that port for
transition detect. Clear the mask bit if transitions on that
port are to be ignored. Transition detection works regardless of whether the port being monitored is set to input or
output, but generally it is not particularly useful to enable
transition detection for outputs.
Any register data within the MAX6957 may be read by
sending a logic high to bit D15. The sequence is:
1) Take SCLK low.
2)Take CS low (this enables the internal 16-bit shift register).
3) Clock 16 bits of data into DIN—D15 first to D0 last.
D15 is high, indicating a read command and bits D14
through D8 containing the address of the register to
be read. Bits D7–D0 contain dummy data, which is
discarded.
4)Take CS high (either while SCLK is still high after
clocking in the last data bit, or after taking SCLK low),
positions D7 through D0 in the Shift register are now
loaded with the register data addressed by bits D1
through D8.
5) Take SCLK low (if not already low).
6) Issue another read or write command (which can
be a No-Op), and examine the bit stream at DOUT;
the second 8 bits are the contents of the register
addressed by bits D1 through D8 in step 3.
Initial Power-Up
On initial power-up, all control registers are reset, current registers are set to minimum value, and the
MAX6957 enters shutdown mode (Table 4).
LED Current Control
LED segment drive current can be set either globally or
individually. Global control simplifies the operation when
all LEDs are set to the same current level, because
writing one register, the Global Current register, sets the
current for all ports configured as LED segment drivers.
It is also possible to individually control the current drive
of each LED segment driver. Individual/global brightness
control is selected by setting the configuration register I
bit (Table7). The global current register (0x02) data are
then ignored, and segment currents are set using register
addresses 0x12 through 0x1F (Tables 10, 11, and 12).
Each segment is controlled by a nibble of one of the 16
current registers.
Transition (Port Data Change) Detection
Port transition detection allows any combination of the
seven ports P24–P30 to be continuously monitored
for changes in their logic status (Figure 6). A detected
change is flagged on port P31, which is used as an
www.maximintegrated.com
Port P31 must be configured as an output in order to work
as the interrupt output INT when transition detection is
used. Port P31 is set as output by writing bit D7 = 0 and
bit D6 = 1 to the port configuration register (Table 1).
To use transition detection, first set up the mask register
and configure port P31 as an output, as described above.
Then enable transition detection by setting the M bit in
the configuration register (Table 8). Whenever the configuration register is written with the M bit set, the MAX6957
updates an internal 7-bit snapshot register, which holds
the comparison copy of the logic states of ports P24
through P30. The update action occurs regardless of the
previous state of the M bit, so that it is not necessary to
clear the M bit and then set it again to update the snapshot register.
When the configuration register is written with the M bit
set, transition detection is enabled and remains enabled
until either the configuration register is written with the M
bit clear, or a transition is detected. The INT output port
P31 goes low, if it was not already low.
Once transition detection is enabled, the MAX6957 continuously compares the snapshot register against the
changing states of P24 through P31. If a change on any
of the monitored ports is detected, even for a short time
(like a pulse), INT output port P31 is latched high. The INT
output is not cleared if more changes occur or if the data
pattern returns to its original snapshot condition. The only
way to clear INT is to access (read or write) the transition
detection mask register (Table 13).
Transition detection is a one-shot event. When INT has
been cleared after responding to a transition event, transition detection is automatically disabled, even though
the M bit in the configuration register remains set (unless
cleared by the user). Reenable transition detection by
writing the configuration register with the M bit set to take
a new snapshot of the seven ports, P24 to P30.
Maxim Integrated │ 10
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 3. Register Address Map
REGISTER
COMMAND ADDRESS
D15
D14
D13
D12
D11
D10
D9
D8
HEX
CODE
No-Op
R/W
0
0
0
0
0
0
0
0x00
Global Current
R/W
0
0
0
0
0
1
0
0x02
Configuration
R/W
0
0
0
0
1
0
0
0x04
Transition Detect Mask
R/W
0
0
0
0
1
1
0
0x06
Display Test
R/W
0
0
0
0
1
1
1
0x07
Port Configuration P7, P6, P5, P4
R/W
0
0
0
1
0
0
1
0x09
Port Configuration P11, P10, P9, P8
R/W
0
0
0
1
0
1
0
0x0A
Port Configuration P15, P14, P13, P12
R/W
0
0
0
1
0
1
1
0x0B
Port Configuration P19, P18, P17, P16
R/W
0
0
0
1
1
0
0
0x0C
Port Configuration P23, P22, P21, P20
R/W
0
0
0
1
1
0
1
0x0D
Port Configuration P27, P26, P25, P24
R/W
0
0
0
1
1
1
0
0x0E
Port Configuration P31, P30, P29, P28
R/W
0
0
0
1
1
1
1
0x0F
Current054
R/W
0
0
1
0
0
1
0
0x12
Current076
R/W
0
0
1
0
0
1
1
0x13
Current098
R/W
0
0
1
0
1
0
0
0x14
Current0BA
R/W
0
0
1
0
1
0
1
0x15
Current0DC
R/W
0
0
1
0
1
1
0
0x16
Current0FE
R/W
0
0
1
0
1
1
1
0x17
Current110
R/W
0
0
1
1
0
0
0
0x18
Current132
R/W
0
0
1
1
0
0
1
0x19
Current154
R/W
0
0
1
1
0
1
0
0x1A
Current176
R/W
0
0
1
1
0
1
1
0x1B
Current198
R/W
0
0
1
1
1
0
0
0x1C
Current1BA
R/W
0
0
1
1
1
0
1
0x1D
Current1DC
R/W
0
0
1
1
1
1
0
0x1E
Current1FE
R/W
0
0
1
1
1
1
1
0x1F
Port 0 only (virtual port, no action)
R/W
0
1
0
0
0
0
0
0x20
Port 1 only (virtual port, no action)
R/W
0
1
0
0
0
0
1
0x21
Port 2 only (virtual port, no action)
R/W
0
1
0
0
0
1
0
0x22
Port 3 only (virtual port, no action)
R/W
0
1
0
0
0
1
1
0x23
Port 4 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
0
1
0
0
0x24
Port 5 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
0
1
0
1
0x25
Port 6 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
0
1
1
0
0x26
Port 7 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
0
1
1
1
0x27
Port 8 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
1
0
0
0
0x28
Port 9 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
1
0
0
1
0x29
Port 10 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
1
0
1
0
0x2A
www.maximintegrated.com
Maxim Integrated │ 11
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 3. Register Address Map (continued)
COMMAND ADDRESS
D15
D14
D13
D12
D11
D10
D9
D8
HEX
CODE
Port 11 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
1
0
1
1
0x2B
Port 12 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
1
1
0
0
0x2C
Port 13 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
1
1
0
1
0x2D
Port 14 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
1
1
1
0
0x2E
Port 15 only (data bit D0. D7–D1 read as 0)
R/W
0
1
0
1
1
1
1
0x2F
Port 16 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
0
0
0
0
0x30
Port 17 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
0
0
0
1
0x31
Port 18 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
0
0
1
0
0x32
Port 19 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
0
0
1
1
0x33
Port 20 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
0
1
0
0
0x34
Port 21 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
0
1
0
1
0x35
Port 22 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
0
1
1
0
0x36
Port 23 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
0
1
1
1
0x37
Port 24 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
1
0
0
0
0x38
Port 25 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
1
0
0
1
0x39
Port 26 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
1
0
1
0
0x3A
Port 27 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
1
0
1
1
0x3B
Port 28 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
1
1
0
0
0x3C
Port 29 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
1
1
0
1
0x3D
Port 30 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
1
1
1
0
0x3E
Port 31 only (data bit D0. D7–D1 read as 0)
R/W
0
1
1
1
1
1
1
0x3F
4 ports 4–7 (data bits D0–D3. D4–D7 read as 0))
R/W
1
0
0
0
0
0
0
0x40
5 ports 4–8 (data bits D0–D4. D5–D7 read as 0)
R/W
1
0
0
0
0
0
1
0x41
6 ports 4–9 (data bits D0–D5. D6–D7 read as 0)
R/W
1
0
0
0
0
1
0
0x42
7 ports 4–10 (data bits D0–D6. D7 reads as 0)
R/W
1
0
0
0
0
1
1
0x43
8 ports 4–11 (data bits D0–D7)
R/W
1
0
0
0
1
0
0
0x44
8 ports 5–12 (data bits D0–D7)
R/W
1
0
0
0
1
0
1
0x45
8 ports 6–13 (data bits D0–D7)
R/W
1
0
0
0
1
1
0
0x46
8 ports 7–14 (data bits D0–D7)
R/W
1
0
0
0
1
1
1
0x47
8 ports 8–15 (data bits D0–D7)
R/W
1
0
0
1
0
0
0
0x48
8 ports 9–16 (data bits D0–D7)
R/W
1
0
0
1
0
0
1
0x49
8 ports 10–17 (data bits D0–D7)
RW
1
0
0
1
0
1
0
0x4A
8 ports 11–18 (data bits D0–D7)
R/W
1
0
0
1
0
1
1
0x4B
8 ports 12–19 (data bits D0–D7)
R/W
1
0
0
1
1
0
0
0x4C
8 ports 13–20 (data bits D0–D7)
R/W
1
0
0
1
1
0
1
0x4D
8 ports 14–21 (data bits D0–D7)
R/W
1
0
0
1
1
1
0
0x4E
8 ports 15–22 (data bits D0–D7)
R/W
1
0
0
1
1
1
1
0x4F
REGISTER
www.maximintegrated.com
Maxim Integrated │ 12
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 3. Register Address Map (continued)
COMMAND ADDRESS
D15
D14
D13
D12
D11
D10
D9
D8
HEX
CODE
8 ports 16–23 (data bits D0–D7)
R/W
1
0
1
0
0
0
0
0x50
8 ports 17–24 (data bits D0–D7)
R/W
1
0
1
0
0
0
1
0x51
8 ports 18–25 (data bits D0–D7)
R/W
1
0
1
0
0
1
0
0x52
8 ports 19–26 (data bits D0–D7)
R/W
1
0
1
0
0
1
1
0x53
8 ports 20–27 (data bits D0–D7)
R/W
1
0
1
0
1
0
0
0x54
8 ports 21–28 (data bits D0–D7)
R/W
1
0
1
0
1
0
1
0x55
8 ports 22–29 (data bits D0–D7)
R/W
1
0
1
0
1
1
0
0x56
8 ports 23–30 (data bits D0–D7)
R/W
1
0
1
0
1
1
1
0x57
8 ports 24–31 (data bits D0–D7)
R/W
1
0
1
1
0
0
0
0x58
7 ports 25–31 (data bits D0–D6. D7 reads as 0)
R/W
1
0
1
1
0
0
1
0x59
6 ports 26–31 (data bits D0–D5. D6, D7 read as 0)
R/W
1
0
1
1
0
1
0
0x5A
5 ports 27–31 (data bits D0–D4. D5–D7 read as 0)
R/W
1
0
1
1
0
1
1
0x5B
4 ports 28–31 (data bits D0–D3. D4–D7 read as 0)
R/W
1
0
1
1
1
0
0
0x5C
3 ports 29–31 (data bits D0–D2. D3–D7 read as 0)
R/W
1
0
1
1
1
0
1
0x5D
2 ports 30–31 (data bits D0–D1. D2–D7 read as 0)
R/W
1
0
1
1
1
1
0
0x5E
R/W
1
0
1
1
1
1
1
0x5F
REGISTER
1 port 31 only (data bit D0. D1–D7 read as 0)
Note: Unused bits read as 0.
Display Test Register
Display test mode turns on all ports configured as LED
drivers by overriding, but not altering, all controls and port
registers, except the port configuration register (Table 14).
Only ports configured as LED drivers are affected. Ports
configured as GPIO push-pull outputs do not change
state. In display test mode, each port’s current is temporarily set to 1/2 the maximum current limit as controlled
by RISET.
Selecting External Component RISET
to Set Maximum Segment Current
The MAX6957 uses an external resistor RISET to set the
maximum segment current. The recommended value,
39kΩ, sets the maximum current to 24mA, which makes
the segment current adjustable from 1.5mA to 24mA in
1.5mA steps.
To set a different segment current, use the formula:
RISET = 936kΩ/ISEG
The recommended value of RISET is the minimum
allowed value, since it sets the display driver to the
maximum allowed segment current. RISET can be a
higher value to set the segment current to a lower maximum value where desired. The user must also ensure
that the maximum current specifications of the LEDs
connected to the driver are not exceeded.
The drive current for each segment can be controlled
through programming either the global current register (Table 9) or individual segment current registers
(Tables 10, 11, and 12), according to the setting of the
current control bit of the configuration register (Table 7).
These registers select the LED’s constant-current drive
from 16 equal fractions of the maximum segment current.
The current difference between successive current steps,
ISTEP, is therefore determined by the formula:
ISTEP = ISEG/16
If ISEG = 24mA, then ISTEP = 24mA/16 = 1.5mA.
where ISEG is the desired maximum segment current in mA.
The recommended value of RISET is 39kΩ.
www.maximintegrated.com
Maxim Integrated │ 13
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
GPIO INPUT
CONDITIONING
GPIO IN
GPIO/PORT
OUTPUT LATCH
GPIO/PORT OUT
P31
INT
OUTPUT LATCH
CLOCK PULSE AFTER EACH READ ACCESS TO MASK REGISTER
R
S
CONFIGURATION REGISTER M BIT = 1
GPIO INPUT
CONDITIONING
P30
GPIO IN
D
Q
GPIO/PORT OUT
MASK REGISTER BIT 6
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P29
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P28
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P27
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P26
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P25
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P24
GPIO/PORT OUTPUT LATCH
GPIO IN
D
Q
GPIO/PORT OUT
GPIO IN
MASK REGISTER BIT 5
D
Q
GPIO/PORT OUT
GPIO IN
MASK REGISTER BIT 4
D
Q
GPIO IN
D
Q
GPIO/PORT OUT
GPIO IN
MASK REGISTER BIT 2
D
Q
GPIO/PORT OUT
GPIO IN
GPIO/PORT OUT
OR
MASK REGISTER BIT 3
GPIO/PORT OUT
MASK REGISTER BIT 1
D
Q
MASK REGISTER LSB
CLOCK PULSE WHEN WRITING CONFIGURATION REGISTER WITH M BIT SET
Figure 6. Maskable GPIO Ports P24 Through P31
www.maximintegrated.com
Maxim Integrated │ 14
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 4. Power-Up Configuration
REGISTER
FUNCTION
POWER-UP CONDITION
Port Register
Bits 4 to 31
ADDRESS
CODE
(HEX)
LED Off; GPIO Output Low
REGISTER DATA
D7
D6
D5
D4
D3
D2
D1
D0
0x24 to
0x3F
X
X
X
X
X
X
X
0
1/16 (minimum on)
0x02
X
X
X
X
0
0
0
0
Shutdown Enabled
Current Control = Global
Transition Detection Disabled
0x04
0
0
X
X
X
X
X
0
All Clear (Masked Off)
0x06
X
0
0
0
0
0
0
0
Display Test
Normal Operation
0x07
X
X
X
X
X
X
X
0
Port
Configuration
P7, P6, P5, P4: GPIO Inputs Without Pullup
0x09
1
0
1
0
1
0
1
0
Port
Configuration
P11, P10, P9, P8: GPIO Inputs Without Pullup
0x0A
1
0
1
0
1
0
1
0
Port
Configuration
P15, P14, P13, P12: GPIO Inputs Without Pullup
0x0B
1
0
1
0
1
0
1
0
Port
Configuration
P19, P18, P17, P16: GPIO Inputs Without Pullup
0x0C
1
0
1
0
1
0
1
0
Port
Configuration
P23, P22, P21, P20: GPIO Inputs Without Pullup
0x0D
1
0
1
0
1
0
1
0
Port
Configuration
P27, P26, P25, P24: GPIO Inputs Without Pullup
0x0E
1
0
1
0
1
0
1
0
Port
Configuration
P31, P30, P29, P28: GPIO Inputs Without Pullup
0x0F
1
0
1
0
1
0
1
0
Current054
1/16 (minimum on)
0x12
0
0
0
0
0
0
0
0
Current076
1/16 (minimum on)
0x13
0
0
0
0
0
0
0
0
Current098
1/16 (minimum on)
0x14
0
0
0
0
0
0
0
0
Current0BA
1/16 (minimum on)
0x15
0
0
0
0
0
0
0
0
Current0DC
1/16 (minimum on)
0x16
0
0
0
0
0
0
0
0
Current0FE
1/16 (minimum on)
0x17
0
0
0
0
0
0
0
0
Current110
1/16 (minimum on)
0x18
0
0
0
0
0
0
0
0
Current132
1/16 (minimum on)
0x19
0
0
0
0
0
0
0
0
Current154
1/16 (minimum on)
0x1A
0
0
0
0
0
0
0
0
Current176
1/16 (minimum on)
0x1B
0
0
0
0
0
0
0
0
Current198
1/16 (minimum on)
0x1C
0
0
0
0
0
0
0
0
Current1BA
1/16 (minimum on)
0x1D
0
0
0
0
0
0
0
0
Current1DC
1/16 (minimum on)
0x1E
0
0
0
0
0
0
0
0
Current1FE
1/16 (minimum on)
0x1F
0
0
0
0
0
0
0
0
Global
Current
Configuration
Register
Input Mask
Register
X = unused bits; if read, zero results.
www.maximintegrated.com
Maxim Integrated │ 15
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 5. Configuration Register Format
REGISTER DATA
FUNCTION
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Configuration Register
0x04
M
0
X
X
X
X
X
S
X = Don’t care bit.
Table 6. Shutdown Control (S Data Bit D0) Format
REGISTER DATA
FUNCTION
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Shutdown
0x04
M
I
X
X
X
X
X
0
Normal Operation
0x04
M
I
X
X
X
X
X
1
X = Don’t care bit.
Table 7. Global Current Control (I Data Bit D6) Format
REGISTER DATA
FUNCTION
ADDRESS
CODE (HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Global
Constant-current limits for all digits are controlled
by one setting in the Global Current register,
0x02
0x04
M
0
X
X
X
X
X
S
Individual Segment
Constant-current limit for each digit is individually
controlled by the settings in the Current054
through Current1FE registers
0x04
M
1
X
X
X
X
X
S
X = Don’t care bit.
Table 8. Transition Detection Control (M-Data Bit D7) Format
REGISTER DATA
FUNCTION
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Disabled
0x04
0
I
X
X
X
X
X
S
Enabled
0x04
1
I
X
X
X
X
X
S
X = Don’t care bit.
Table 9. Global Segment Current Register Format
LED DRIVE
FRACTION
TYPICAL SEGMENT
CURRENT (mA)
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
HEX CODE
1/16
1.5
0x02
X
X
X
X
0
0
0
0
0xX0
2/16
3
0x02
X
X
X
X
0
0
0
1
0xX1
3/16
4.5
0x02
X
X
X
X
0
0
1
0
0xX2
4/16
6
0x02
X
X
X
X
0
0
1
1
0xX3
5/16
7.5
0x02
X
X
X
X
0
1
0
0
0xX4
X = Don’t care bit.
www.maximintegrated.com
Maxim Integrated │ 16
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 9. Global Segment Current Register Format (continued)
LED DRIVE
FRACTION
TYPICAL SEGMENT
CURRENT (mA)
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
HEX CODE
6/16
9
0x02
X
X
X
X
0
1
0
1
0xX5
7/16
10.5
0x02
X
X
X
X
0
1
1
0
0xX6
8/16
12
0x02
X
X
X
X
0
1
1
1
0xX7
9/16
13.5
0x02
X
X
X
X
1
0
0
0
0xX8
10/16
15
0x02
X
X
X
X
1
0
0
1
0xX9
11/16
16.5
0x02
X
X
X
X
1
0
1
0
0xXA
12/16
18
0x02
X
X
X
X
1
0
1
1
0xXB
13/16
19.5
0x02
X
X
X
X
1
1
0
0
0xXC
14/16
21
0x02
X
X
X
X
1
1
0
1
0xXD
15/16
22.5
0x02
X
X
X
X
1
1
1
0
0xXE
16/16
24
0x02
X
X
X
X
1
1
1
1
0xXF
X = Don’t care bit.
Table 10. Individual Segment Current Registers
REGISTER
ADDRESS
FUNCTION
CODE (HEX)
Current054 register
0x12
Segment 5
Segment 4
Current076 register
0x13
Segment 7
Segment 6
Current098 register
0x14
Segment 9
Segment 8
D7
D6
D5
D4
D3
D2
D1
Current0BA register
0x15
Segment 11
Segment 10
Current0DC register
0x16
Segment 13
Segment 12
Current0FE register
0x17
Segment 15
Segment 14
Current110 register
0x18
Segment 17
Segment 16
Current132 register
0x19
Segment 19
Segment 18
Current154 register
0x1A
Segment 21
Segment 20
Current176 register
0x1B
Segment 23
Segment 22
Current198 register
0x1C
Segment 25
Segment 24
Current1BA register
0x1D
Segment 27
Segment 26
Current1DC register
0x1E
Segment 29
Segment 28
Current1FE register
0x1F
Segment 31
Segment 30
www.maximintegrated.com
D0
Maxim Integrated │ 17
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 11. Even Individual Segment Current Format
SEGMENT
LED DRIVE
CONSTANT
ADDRESS CODE
FRACTION
CURRENT WITH
(HEX)
1/16
RISET = 39kΩ (mA)
D7
D6
D5
D4
D3
D2
D1
D0
HEX CODE
1.5
0x12 to 0x1F
0
0
0
0
0xX0
2/16
3
0x12 to 0x1F
0
0
0
1
0xX1
3/16
4.5
0x12 to 0x1F
0
0
1
0
0xX2
4/16
6
0x12 to 0x1F
0
0
1
1
0xX3
5/16
7.5
0x12 to 0x1F
0
1
0
0
0xX4
6/16
9
0x12 to 0x1F
0
1
0
1
0xX5
7/16
10.5
0x12 to 0x1F
0
1
1
0
0xX6
8/16
12
0x12 to 0x1F
0
1
1
1
0xX7
9/16
13.5
0x12 to 0x1F
1
0
0
0
0xX8
10/16
15
0x12 to 0x1F
1
0
0
1
0xX9
11/16
16.5
0x12 to 0x1F
1
0
1
0
0xXA
12/16
18
0x12 to 0x1F
1
0
1
1
0xXB
13/16
19.5
0x12 to 0x1F
1
1
0
0
0xXC
14/16
21
0x12 to 0x1F
1
1
0
1
0xXD
15/16
22.5
0x12 to 0x1F
1
1
1
0
0xXE
16/16
24
0x12 to 0x1F
1
1
1
1
0xXF
Applications Information
See Table 12.
Driving Bicolor and Tricolor LEDs
of the 36-pin SSOP package with an ambient temperature up to +98°C. If a higher supply voltage is used or
the LEDs used have a lower forward-voltage drop than
2.4V, the MAX6957 absorbs a higher voltage, and the
MAX6957’s power dissipation increases.
Power Dissipation Issues
If the application requires high drive current and high
supply voltage, consider adding a series resistor to
each LED to drop excessive drive voltage off-chip. For
example, consider the requirement that the MAX6957
must drive LEDs with a 2.0V to 2.4V specified forwardvoltage drop, from an input supply range is 5V ±5%
with a maximum LED current of 20mA. Minimum input
supply voltage is 4.75V. Maximum LED series resistor
value is (4.75V - 2.4V - 0.6V)/0.020A = 87.5Ω. We
choose 82Ω ± 2%. Worst-case resistor dissipation is at
maximum toleranced resistance, i.e., (0.020A)2 5 (82Ω
× 1.02) = 34mW. The maximum MAX6957 dissipation
per LED is at maximum input supply voltage, minimum
toleranced resistance, mini-mum toleranced LED forward-voltage drop, i.e., 0.020 × (5.25V - 2.0V - (0.020A
× 82Ω × 0.98)) = 32.86mW. Worst-case MAX6957 dissipation is 920mW, driving all 28 LEDs at 20mA full current at once, which meets the 941mW dissipation ratings
of the 36-pin SSOP package.
Bicolor digits group a red and a green die together for
each display element, so that the element can be lit red,
green (or orange), depending on which die (or both) is lit.
The MAX6957 allows each segment’s current to be set
individually from 1/16th (minimum current and LED intensity) to 16/16th (maximum current and LED intensity), as
well as off (zero current). Thus, a bicolor (red-green) segment pair can be set to 289 color/intensity combinations.
A discrete or CA tricolor (red-green-yellow or red-greenblue) segment triad can be set to 4913 color/intensity
combinations.
Each MAX6957 port can sink a current of 24mA into an
LED with a 2.4V forward-voltage drop when operated
from a supply voltage of at least 3.0V. The minimum
voltage drop across the internal LED drivers is therefore
(3.0V - 2.4V) = 0.6V. The MAX6957 can sink 28 x 24mA
= 672mA when all outputs are operating as LED segment
drivers at full current. On a 3.3V supply, a MAX6957 dissipates (3.3V - 2.4V) 5 672mA = 0.6W when driving 28 of
these 2.4V forward-voltage drop LEDs at full current. This
dissipation is within the ratings
www.maximintegrated.com
Maxim Integrated │ 18
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Low-Voltage Operation
up initially to at least 2.5V to trigger the device’s internal
reset, and also that the serial interface is constrained to
10Mbps.
The MAX6957 operates down to 2V supply voltage
(although the sourcing and sinking currents are not
guaranteed), providing that the MAX6957 is powered
Table 12. Odd Individual Segment Current Format
LED DRIVE
SEGMENT CONSTANT
FRACTION
CURRENT WITH
ADDRESS CODE
(HEX)
RISET = 39kΩ (mA)
1/16
D7
D6
D5
D4
D3
D2
D1
D0
HEX CODE
1.5
0x12 to 0x1F
0
0
0
0
0x0X
2/16
3
0x12 to 0x1F
0
0
0
1
0x1X
3/16
4.5
0x12 to 0x1F
0
0
1
0
0x2X
4/16
6
0x12 to 0x1F
0
0
1
1
0x3X
5/16
7.5
0x12 to 0x1F
0
1
0
0
0x4X
6/16
9
0x12 to 0x1F
0
1
0
1
0x5X
7/16
10.5
0x12 to 0x1F
0
1
1
0
8/16
12
0x12 to 0x1F
0
1
1
1
0x6X
See Table 11.
0x7X
9/16
13.5
0x12 to 0x1F
1
0
0
0
0x8X
10/16
15
0x12 to 0x1F
1
0
0
1
0x9X
11/16
16.5
0x12 to 0x1F
1
0
1
0
0xAX
12/16
18
0x12 to 0x1F
1
0
1
1
0xBX
13/16
19.5
0x12 to 0x1F
1
1
0
0
0xCX
14/16
21
0x12 to 0x1F
1
1
0
1
0xDX
15/16
22.5
0x12 to 0x1F
1
1
1
0
0xEX
16/16
24
0x12 to 0x1F
1
1
1
1
0xFX
X = Don’t care bit.
Table 13. Transition Detection Mask Register
FUNCTION
REGISTER
ADDRESS
(HEX)
Mask
Register
0x06
REGISTER DATA
READ/
WRITE
D7
D6
D5
D4
D3
D2
D1
D0
Read
0
Write
Unchanged
Port
30
mask
Port
29
mask
Port
28
mask
Port
27
mask
Port
26
mask
Port
25
mask
Port
24
mask
X = Don’t care bit.
Table 14. Display Test Register
REGISTER DATA
MODE
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Normal Operation
0x07
X
X
X
X
X
X
X
0
Display Test Mode
0x07
X
X
X
X
X
X
X
1
www.maximintegrated.com
Maxim Integrated │ 19
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
SPI Routing Considerations
The MAX6957’s SPI interface is guaranteed to operate at
26Mbps on a 2.5V supply, and on a 5V supply typically
operates at 50Mbps. This means that the transmission
line issues should be considered when the interface connections are longer that 100mm, particularly with higher
supply voltages. Ringing manifests itself as communication issues, often intermittent, typically due to double
clocking due to ringing at the SCLK input. Fit a 1kΩ to
10kΩ parallel termination resistor to either GND or V+ at
the DIN, SCLK, and CS input to damp ringing for moderately long interface runs. Use line impedance matching
terminations when making connections between boards.
PC Board Layout Considerations
Ensure that all the MAX6957 GND connections are
used. A ground plane is not necessary, but may be
useful to reduce supply impedance if the MAX6957
outputs are to be heavily loaded. Keep the track length
from the ISET pin to the RISET resistor as short as possible, and take the GND end of the resistor either to the
ground plane or directly to the GND pins.
Power-Supply Considerations
The MAX6957 operates with power-supply voltages of
2.5V to 5.5V. Bypass the power supply to GND with a
0.047µF capacitor as close to the device as possible.
Add a 1µF capacitor if the MAX6957 is far away from the
board’s input bulk decoupling capacitor.
Chip Information
PROCESS: CMOS
Pin Configurations (continued)
6
31 P31
P9
7
30 P5
P13
8
29 P30
P10
9
1
30
2
29
3
28
4
27
P11
P15
P16
7
24
8
23
P4
P31
P5
P30
P6
P29
P7
P28
9
22
P27
P17
10
21
P26
5
26
MAX6957
18
19
P24
P25
N.C.
P17 14
23 P26
P18 15
22 P25
P19 16
21 P24
P20 17
20 P23
P21 18
19 P22
20
17
24 P27
16
25 P28
P16 13
15
26 P7
P15 12
14
27 P29
P11 11
13
P14 10
12
25
11
6
P18
P19
P20
P21
P22
P23
28 P6
P8
P12
P9
P13
P10
P14
N.C.
MAX6957
N.C.
P12
31
32 P4
32
5
33
P8
34
33 SCLK
35
4
GND
ISET
V+
CS
DIN
SCLK
DOUT
36
34 DIN
37
3
GND
GND
35 CS
GND
38
2
DOUT
36 V+
GND
39
ISET 1
40
TOP VIEW
TQFN
SSOP
www.maximintegrated.com
Maxim Integrated │ 20
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Typical Operating Circuit
3V
3V
P4 32
P5 30
P6 28
P7 26
36 V+
47nF
39kΩ
3 GND
2 GND
1 ISET
34 DIN
33 SCLK
35 CS
4-WIRE DATA IN
4-WIRE CLOCK IN
CHIP SELECT
4 DOUT
U1
MAX6957AAX
31 P31
29 P30
27 P29
25 P28
24 P27
23 P26
22 P25
21 P24
P8 5
P9 7
P10 9
P11 11
P12 6
P13 8
P14 10
P15 12
P16 13
P17 14
P18 15
P19 16
P20 17
P21 18
P22 19
P23 20
a1
a2
LED1
b
c
d1
d2
e
f
g1
g2
h
i
j
k
l
m
dp
ca
a1
a2
LED2
b
c
d1
d2
e
f
g1
g2
h
i
3V
36 V+
47nF
39kΩ
3 GND
2 GND
1 ISET
34 DIN
U2
33 SCLK
MAX6957AAX
35 CS
4 DOUT
4-WIRE DATA OUT
31 P31
29 P30
27 P29
25 P28
24 P27
IRQ OUT
1
SW1 SW2
www.maximintegrated.com
2
SW3
23 P26
22 P25
21
P24
32
P4
30
P5
28
P6
26
P7
5
P8
7
P9
P10 9
P11 11
P12 6
P13 8
P14 10
P15 12
P16 13
P17 14
P18 15
P19 16
P20 17
P21 18
P22 19
P23 20
j
k
l
m
dp
ca
a1
a2
LED3
b
c
d1
d2
e
f
g1
g2
h
i
j
k
l
m
dp
ca
Maxim Integrated │ 21
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”,
“#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing
pertains to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
LAND PATTERN NO.
28 PDIP
N28-2
21-0043
—
28 SSOP
A28-1
21-0056
90-0095
36 SSOP
A36-4
21-0040
90-0098
T4066+5
21-0141
90-0055
40 TQFN-EP
www.maximintegrated.com
Maxim Integrated │ 22
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
DESCRIPTION
0
4/02
Initial Release
1
10/02
Corrected data sheet
—
2
2/03
Revised Electrical Characteristics table and added QFN package
3
11/03
Package change, added new sections
4
2/07
Added exposed pad information to Genaral Description, package code to
Ordering Information, corrected Absolute Maximum Ratings, TQFN pinout
information to Pin Description
5
7/14
Removed automotive reference from data sheet
1, 3, 5, 9, 10, 11, 14, 19
1, 3
1, 5-7, 10-14, 18,
20, 24 25
1, 2, 5
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2014 Maxim Integrated Products, Inc. │ 23