MAXIM MAX6957AAX

19-2429; Rev 0; 4/02
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
The MAX6957 compact, serial-interfaced LED display
driver general-purpose I/O (GPIO) peripheral provides
microprocessors with up to 28 ports. Each port is individually user configurable to either a logic input, logic
output, or common-anode (CA) LED constant-current
segment driver. Each port configured as an LED segment driver behaves as a digitally controlled constantcurrent sink, with 16 equal current steps from 1.5mA to
24mA. The LED drivers are suitable for both discrete
LEDs and CA numeric and alphanumeric LED digits.
Each port configured as a GPIO can be either a pushpull logic output capable of sinking 10mA and sourcing
4.5mA, or a Schmitt logic input with optional internal
pullup. Seven ports feature configurable transition
detection logic, which generates an interrupt upon
change of port logic level. The MAX6957 is controlled
through an SPI™-compatible 4-wire serial interface.
The MAX6957AAX and MAX6957AGL have 28 ports and
are available in 36-pin SSOP and 40-pin QFN packages,
respectively. The MAX6957AAI and MAX6957ANI have
20 ports and are available in 28-pin SSOP and 28-pin DIP
packages, respectively.
Applications
Set-Top Boxes
Features
♦ High-Speed 26MHz SPI-/QSPI-™/MICROWIRE™Compatible Serial Interface
♦ 2.5V to 5.5V Operation
♦ -40°C to +125°C Temperature Range
♦ 20 or 28 I/O Ports, Each Configurable as
Constant-Current LED Driver
Push-Pull Logic Output
Schmitt Logic Input
Schmitt Logic Input with Internal Pullup
♦ 11µA (max) Shutdown Current
♦ 16-Step Individually Programmable Current
Control for Each LED
♦ Logic Transition Detection for Seven I/O Ports
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
MAX6957ANI
-40°C to +125°C
28 DIP
MAX6957AAI
-40°C to +125°C
28 SSOP
MAX6957AAX
-40°C to +125°C
36 SSOP
MAX6957AGL*
-40°C to +125°C
40 QFN
*Future product—contact factory for availability.
Panel Meters
Pin Configurations
White Goods
TOP VIEW
Automotive
Bar Graph Displays
ISET 1
28 V+
Industrial Controllers
GND 2
27 CS
GND 3
26 DIN
System Monitoring
25 SCLK
DOUT 4
P12 5
24 P31
P13 6
23 P30
P14 7
Typical Operating Circuit appears at end of data sheet.
SPI and QSPI are trademarks of Motorola, Inc.
MICROWIRE is a trademark of National Semiconductor Corp.
MAX6957
22 P29
P15 8
21 P28
P16 9
20 P27
P17 10
19 P26
P18 11
18 P25
P19 12
17 P24
P20 13
16 P23
P21 14
15 P22
SSOP/DIP
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX6957
General Description
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
ABSOLUTE MAXIMUM RATINGS
Voltage (with Respect to GND)
V+ .............................................................................-0.3V to +6V
All Other pins................................................-0.3V to (V+ + 0.3V)
P4–P31 Current ................................................................±30mA
GND Current .....................................................................800mA
Continuous Power Dissipation (TA = +70°C)
28-Pin PDIP (derate 20.8mW/°C above +70°C)........1667mW
28-Pin SSOP (derate 9.5mW/°C above +70°C) ..........762mW
36-Pin SSOP (derate 11.8mW/°C above +70°C) ........941mW
Operating Temperature Range (TMIN, TMAX) ....-40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(Typical Operating Circuit, V+ = 2.5V to 5.5V, TA = TMIN to TMAX, unless otherwise noted.) (Note 1)
PARAMETER
Operating Supply Voltage
Shutdown Supply Current
Operating Supply Current
Operating Supply Current
Operating Supply Current
SYMBOL
CONDITIONS
V+
ISHDN
IGPOH
IGPOL
ILED
MIN
TYP
2.5
All digital inputs at
V+ or GND
TA = +25°C
5.5
MAX
UNITS
5.5
V
8
TA = -40°C to +85°C
10
TA = TMIN to TMAX
11
All ports programmed
TA = +25°C
as outputs high, no load,
TA = -40°C to +85°C
all other inputs at V+ or
TA = TMIN to TMAX
GND
180
All ports programmed
as outputs low, no load,
all other inputs at V+ or
GND
170
µA
230
250
µA
270
TA = +25°C
210
TA = -40°C to +85°C
230
TA = TMIN to TMAX
240
All ports programmed
TA = +25°C
as LED outputs, all LEDs
TA = -40°C to +85°C
off, no load, all other
TA = TMIN to TMAX
inputs at V+ or GND
110
µA
135
140
µA
145
INPUTS AND OUTPUTS
Logic-High Input Voltage
Port Inputs
VIH
Logic-Low Input Voltage
Port Inputs
VIL
GPIO Input Internal Pullup to V+
IPU
Hysteresis Voltage GPIO Inputs
∆VI
Output High Voltage
2
VOH
0.7 ✕
V+
V
0.3 ✕
V+
V+ = 2.5V
12
19
30
V+ = 5.5V
80
120
180
0.3
V
µA
V
GPIO outputs, ISOURCE = 2mA, TA = -40°C to
+85°C
V+ 0.7
V
GPIO outputs, ISOURCE = 1mA,
TA = TMIN to TMAX (Note 2)
V+ 0.7
V
_______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
(Typical Operating Circuit, V+ = 2.5V to 5.5V, TA = TMIN to TMAX, unless otherwise noted.) (Note 1)
PARAMETER
Port Sink Current
SYMBOL
IOL
Output Short-Circuit Current
Port Drive LED Sink Current,
Port Configured as LED Driver
Port Drive Logic Sink Current,
Port Configured as LED Driver
IOLSC
IDIGIT
IDIGIT_SC
Input High-Voltage SCLK, DIN,
CS
VIH
Input Low-Voltage SCLK, DIN, CS
VIL
Input Leakage Current SCLK,
DIN, CS
CONDITIONS
MIN
TYP
MAX
2
10
18
mA
Port configured output low, shorted to V+
2.75
11
20
mA
V+ = 2.5V, VLED = 2.3V at maximum LED
current
9.5
13.5
18
V+ = 3.3V, VLED = 2.4V at maximum LED
current (Note 2)
18.5
24
27.5
V+ = 5.5V, VLED = 2.4V at maximum LED
current
19
25
30
V+ = 2.5V, VOUT = 0.6V at maximum LED
current
18.5
23
28.0
V+ = 5.5V, VOUT = 0.6V at maximum LED
current
19
24
28
V+ ≤ 3.3V
1.6
V+ > 3.3V
2
VPORT = 0.6V
UNITS
mA
mA
IIH, IIL
V
-50
Output High-Voltage DOUT
VOH
ISOURCE = 1.6mA
Output Low-Voltage DOUT
VOL
ISINK = 1.6mA
0.6
V
+50
nA
V+ 0.5
V
0.4
V
MAX
UNITS
TIMING CHARACTERISTICS (Figure 3)
(V+ = 2.5V to 5.5V, TA = TMIN to TMAX, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
CLK Clock Period
tCP
38.4
ns
CLK Pulse Width High
tCH
19
ns
CLK Pulse Width Low
tCL
19
ns
CS Fall to SCLK Rise Setup Time
tCSS
9.5
ns
CLK Rise to CS Rise Hold Time
tCSH
0
ns
DIN Setup Time
tDS
9.5
ns
DIN Hold Time
tDH
0
ns
Output Data Propagation Delay
Minimum CS Pulse High
tDO
tCSW
CLOAD = 25pF
21
19
ns
ns
Note 1: All parameters tested at TA = +25°C. Specifications over temperature are guaranteed by design.
Note 2: Guaranteed by design.
_______________________________________________________________________________________
3
MAX6957
ELECTRICAL CHARACTERISTICS (continued)
__________________________________________Typical Operating Characteristics
(RISET = 39kΩ, TA = +25°C, unless otherwise noted.)
0.24
0.20
0.16
0.12
6
V+ = 2.5V
MAX6957 toc03
ALL PORTS OUTPUT (1)
1
ALL PORTS OUTPUT (0)
0.1
ALL PORTS LED (OFF)
0.04
ALL PORTS LED (OFF)
0.01
3
0
-12.5
15.0
42.5
70.0
97.5
-40.0
125.0
-12.5
15.0
42.5
70.0
97.5
2.0
125.0
3.0
3.5
4.0
4.5
5.0
V+ (V)
LED DRIVER SINK CURRENT vs. V+
LED DRIVER SINK CURRENT
vs. TEMPERATURE
GPO SINK CURRENT vs. TEMPERATURE
(OUTPUT = 0)
20
LED DROP = 2.4V
18
16
LED DROP = 1.8V
14
12
26
10
V+ = 5.5V
18
25
24
23
V+ = 3.3V
22
V+ = 2.5V TO 5.5V, VPORT = 0.6V
16
21
20
2.5
3.0
3.5
4.0
4.5
5.0
12
10
8
6
2
-40.0
5.5
14
4
8
6
MAX6957 toc06
VLED = 2.4V
PORT SINK CURRENT (mA)
22
27
MAX6957 toc05
MAX6957 toc04
24
-12.5
15.0
42.5
70.0
97.5
125.0
-40.0
-12.5
15.0
42.5
70.0
97.5
V+ (V)
TEMPERATURE (°C)
TEMPERATURE (°C)
GPO SOURCE CURRENT vs. TEMPERATURE
(OUTPUT = 1)
GPI PULLUP CURRENT
vs. TEMPERATURE
GPO SHORT-CIRCUIT CURRENT
vs. TEMPERATURE
PULLUP CURRENT (µA)
V+ = 5.5V
V+ = 3.3V
6
5
V+ = 2.5V
4
PORT CURRENT (mA)
V+ = 5.5V
100
V+ = 3.3V
GPO = 0, PORT
SHORTED TO V+
10
V+ = 2.5V
3
2
GPO = 1, PORT
SHORTED TO GND
10
-12.5
15.0
42.5
70.0
TEMPERATURE (°C)
97.5
125.0
125.0
MAX6957 toc09
8
100
MAX6957 toc08
VPORT = 1.4V
7
1000
MAX6957 toc07
9
-40.0
5.5
TEMPERATURE (°C)
26
2.0
2.5
TEMPERATURE (°C)
PORT SINK CURRENT (mA)
-40.0
4
10
4
0.08
PORT SINK CURRENT (mA)
V+ = 3.3V
5
ALL PORTS LED (ON)
SUPPLY CURRENT (mA)
ALL PORTS
OUTPUT (0)
ALL PORTS
OUTPUT (1)
V+ = 5.5V
7
SUPPLY CURRENT (µA)
SUPPLY CURRENT (mA)
0.32
100
MAX6957 toc02
V+ = 2.5V TO 5.5V
NO LOAD
0.28
8
MAX6957 toc01
0.40
0.36
OPERATING SUPPLY CURRENT vs. V+
(NO LOADS)
SHUTDOWN SUPPLY CURRENT
vs. TEMPERATURE
OPERATING SUPPLY CURRENT
vs. TEMPERATURE
PORT SOURCE CURRENT (mA)
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
1
-40.0
-12.5
15.0
42.5
70.0
TEMPERATURE (°C)
97.5
125.0
-40.0
-12.5
15.0
42.5
70.0
TEMPERATURE (°C)
_______________________________________________________________________________________
97.5
125.0
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
PIN
NAME
FUNCTION
SSOP
DIP
SSOP
1
1
ISET
Segment Current Setting. Connect ISET to GND through a resistor (RISET) to set the
maximum segment current.
2, 3
2, 3
GND
Ground
4
4
DOUT
4-Wire Serial Data Output Port
5–24
—
P12–P31
LED Segment Drivers and GPIO. P12 to P31 can be configured as CA LED drivers, GPIO
outputs, CMOS logic inputs, or CMOS logic inputs with weak pullup resistor.
—
5–32
P4–P31
LED Segment Drivers and GPIO. P4 to P31 can be configured as CA LED drivers, GPIO
outputs, CMOS logic inputs, or CMOS logic inputs with weak pullup resistor.
25
33
SCLK
4-Wire Serial Clock Input Port
26
34
DIN
4-Wire Serial Data Input Port
27
35
CS
4-Wire Chip-Select Input, Active Low
28
36
V+
Positive Supply Voltage. Bypass V+ to GND with a minimum 0.047µF capacitor.
Detailed Description
The MAX6957 LED driver/GPIO peripheral provides up
to 28 I/O ports, P4 to P31, controlled through an SPIcompatible serial interface. The ports can be configured to any combination of constant-current LED
drivers, logic inputs and logic outputs, and default to
logic inputs on power-up. When fully configured as an
LED driver, the MAX6957 controls up to 28 LED segments with individual 16-step adjustment of the constant current through each LED segment. A single
resistor sets the maximum segment current for all segments, with a maximum of 24mA per segment. The
MAX6957 drives any combination of discrete LEDs and
CA digits, including seven-segment and starburst
alphanumeric types.
Figure 1 is the MAX6957 functional diagram. Any I/O
port can be configured as a push-pull output (sinking
10mA, sourcing 4.5mA), or a Schmitt-trigger logic
input. Each input has an individually selectable internal
pullup resistor. Additionally, transition detection allows
seven ports (P24 through P30) to be monitored in any
maskable combination for changes in their logic status.
A detected transition is flagged through a status register bit, as well as an interrupt pin (port P31), if desired.
The Typical Operating Circuit shows two MAX6957s
working together controlling three monocolor 16-segment-plus-DP displays, with five ports left available for
GPIO (P27–P31 of U2).
The port configuration registers set the 28 ports, P4 to
P31, individually as either LED drivers or GPIO. A pair
of bits in registers 0x09 through 0x0F sets each port’s
configuration (Tables 1 and 2).
The 36-pin MAX6957AAX has 28 ports, P4 to P31. The
28-pin MAX6957ANI and MAX6957AAI only use 20 outputs, P12 to P31. The eight unused ports should be
configured as outputs on power-up by writing 0x55 to
registers 0x09 and 0x0A. If this is not done, the eight
unused ports remain as floating inputs and quiescent
supply current rises, although there is no damage to
the part.
Register Control of I/O Ports and LEDs
Across Multiple Drivers
The MAX6957 offers 20 or 28 I/O ports, depending on
package choice. These can be applied to a variety of
combinations of different display types, for example:
seven, 7-segment digits (Figure 2). This example
requires two MAX6957s, with one digit being driven by
both devices, half by one MAX6957, half by the other
(digit 4 in this example). The two drivers are static, and
therefore do not need to be synchronized. The
MAX6957 sees CA digits as multiple discrete LEDs. To
simplify access to displays that overlap two MAX6957s,
the MAX6957 provides four virtual ports P0 through P3.
To update an overlapping digit, send the same code
twice as an eight-port write, once to P28 through P35 of
the first driver, and again to P0 through P7 of the sec-
_______________________________________________________________________________________
5
MAX6957
Pin Description
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 1. Port Configuration Map
REGISTER DATA
ADDRESS
CODE (HEX)
REGISTER
Port Configuration for P7, P6, P5, P4
D7
0x09
D6
D5
P7
D4
D3
P6
D2
P5
D1
D0
P4
Port Configuration for P11, P10, P9, P8
0x0A
P11
P10
P9
P8
Port Configuration for P15, P14, P13, P12
0x0B
P15
P14
P13
P12
Port Configuration for P19, P18, P17, P16
0x0C
P19
P18
P17
P16
Port Configuration for P23, P22, P21, P20
0x0D
P23
P22
P21
P20
Port Configuration for P27, P26, P25, P24
0x0E
P27
P26
P25
P24
Port Configuration for P31, P30, P29, P28
0x0F
P31
P30
P29
P28
Table 2. Port Configuration Matrix
MODE
FUNCTION
PORT
REGISTER
Written Low
Output
LED Segment Driver
Output
GPIO Output
Input
Input
Written High
PIN BEHAVIOR
ADDRESS
CODE (HEX)
PORT
CONFIGURATION
BIT PAIR
UPPER
LOWER
0x09 to 0x0F
0
0
0x09 to 0x0F
0
1
High impedance
Open-drain current sink, with sink
current (up to 24mA) determined
by the appropriate current register
Written Low
Active-low logic output
Written High
Active-high logic output
GPIO Input
Without Pullup
Reading Port
Schmitt logic input
0x09 to 0x0F
1
0
GPIO Input with Pullup
Reading Port
Schmitt logic input with pullup
0x09 to 0x0F
1
1
Note: The logic is inverted between the two output modes; a high makes the output go low in LED segment driver mode (0x00) to
turn that segment on; in GPIO output mode (0x01), a high makes the output go high.
ond driver. The first driver ignores the last 4 bits and
the second driver ignores the first 4 bits.
Two addressing methods are available. Any single port
(bit) can be written (set/cleared) at once; or, any
sequence of eight ports can be written (set/cleared) in
any combination at once. There are no boundaries; it is
equally acceptable to write P0 through P7, P1 through
P8, or P31 through P38 (P32 through P38 are nonexistent, so the instructions to these bits are ignored).
Using 8-bit control, a seven-segment digit with a decimal point can be updated in a single byte-write, a 14segment digit with DP can be updated in two
byte-writes, and 16-segment digits with DP can be
updated in two byte-writes plus a bit write. Also, discrete LEDs and GPIO port bits can be lit and controlled
individually without affecting other ports.
6
Shutdown
When the MAX6957 is in shutdown mode, all ports are
forced to inputs, and the pullup current sources are
turned off. Data in the port and control registers remain
unaltered so port configuration and output levels are
restored when the MAX6957 is taken out of shutdown.
The display driver can still be programmed while in
shutdown mode. For minimum supply current in shutdown mode, logic inputs should be at GND or V+
potential. Shutdown mode is exited by setting the S bit
in the configuration register (Table 6). Shutdown mode
is temporarily overridden by the display test function.
_______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
MAX6957
INTENSITY REGISTERS
INTENSITY
TEST REGISTER
TEST
PORT REGISTERS
CONFIGURATION
MASK REGISTER
P4 TO P31
LED DRIVERS
OR GPIO
LED DRIVERS AND GPIO
CONFIGURATION
REGISTERS
PORT CHANGE
DETECTOR
DATA
CE
R/W
8
SEGMENT OR
GPIO DATA
R/W
8
COMMAND
REGISTER DECODE
8
8
DATA BYTE
COMMAND BYTE
CS
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
DIN
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
DOUT
SCLK
Figure 1. MAX6957 Functional Diagram
Serial Interface
The MAX6957 communicates through an SPI-compatible 4-wire serial interface. The interface has three
inputs, Clock (SCLK), Chip Select (CS), and Data In
(DIN), and one output, Data Out (DOUT). CS must be
low to clock data into or out of the device, and DIN
must be stable when sampled on the rising edge of
SCLK. DOUT provides a copy of the bit that was input
15.5 clocks earlier, or upon a query it outputs internal
register data, and is stable on the rising edge of SCLK.
Note that the SPI protocol expects DOUT to be high
impedance when the MAX6957 is not being accessed;
DOUT on the MAX6957 is never high impedance.
SCLK and DIN may be used to transmit data to other
peripherals, so the MAX6957 ignores all activity on
SCLK and DIN except between the fall and subsequent
rise of CS.
Control and Operation Using the
4-Wire Interface
Controlling the MAX6957 requires sending a 16-bit
word. The first byte, D15 through D8, is the command
address (Table 3), and the second byte, D7 through
D0, is the data byte (Table 4).
Connecting Multiple MAX6957s to the 4-Wire Bus
Multiple MAX6957s may be daisy-chained by connecting the DOUT of one device to the DIN of the next, and
driving SCLK and CS lines in parallel (Figure 4). Data at
DIN propagates through the internal shift registers and
appears at DOUT 15.5 clock cycles later, clocked out
on the falling edge of SCLK. When sending commands
_______________________________________________________________________________________
7
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
7-SEGMENT DIGIT 1
7-SEGMENT DIGIT 2
7-SEGMENT DIGIT 3
7-SEGMENT DIGIT 4
VIRTUAL SEGMENTS
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31
7-SEGMENT DIGIT 5
7-SEGMENT DIGIT 6
7-SEGMENT DIGIT 7
V+
VIRTUAL SEGMENTS
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31
Figure 2. Two MAX6957s Controlling Seven 7-Segment Displays
CS
tCSS
tCH
tCSH
tCSH
tCL
SCLK
tDS
tDH
DIN
tDV
tDO
DOUT
Figure 3. 4-Wire Interface Timing
8
_______________________________________________________________________________________
V+
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
MAX6957
MICROCONTROLLER
SERIAL DATA INPUT
SERIAL CS OUTPUT
CS
CS
CS
MAX6957
MAX6957
DOUT
DIN
SERIAL DATA OUTPUT
MAX6957
SCLK
SCLK
SERIAL CLOCK OUTPUT
SCLK
DIN
DOUT
DIN
DOUT
Figure 4. Daisy-Chain Arrangement for Controlling Multiple MAX6957s
CS
SCLK
DIN
D15
=0
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
DOUT
D3
D2
D1
D0
D15 = 0
.
Figure 5. 16-Bit Write Transmission to the MAX6957
to multiple MAX6957s, all devices are accessed at the
same time. An access requires (16 ✕ n) clock cycles,
where n is the number of MAX6957s connected together. To update just one device in a daisy-chain, the user
can send the No-Op command (0x00) to the others.
Writing Device Registers
The MAX6957 contains a 16-bit shift register into which
DIN data are clocked on the rising edge of SCLK, when
CS is low. When CS is high, transitions on SCLK have
no effect. When CS goes high, the 16 bits in the Shift
register are parallel loaded into a 16-bit latch. The 16
bits in the latch are then decoded and executed.
The MAX6957 is written to using the following
sequence:
1) Take SCLK low.
2) Take CS low. This enables the internal 16-bit shift
register.
3) Clock 16 bits of data into DIN—D15 first, D0 last—
observing the setup and hold times (bit D15 is low,
indicating a write command).
4) Take CS high (while SCLK is still high after clocking
in the last data bit).
5) Take SCLK low.
Figure 5 shows a write operation when 16 bits are
transmitted.
It is acceptable to clock more than 16 bits into the
MAX6957 between taking CS low and taking CS high
again. In this case, only the last 16 bits clocked into the
MAX6957 are retained.
Reading Device Registers
Any register data within the MAX6957 may be read by
sending a logic high to bit D15. The sequence is:
1) Take SCLK low.
2) Take CS low (this enables the internal 16-bit shift
register).
3) Clock 16 bits of data into DIN—D15 first to D0 last.
D15 is high, indicating a read command and bits
D14 through D8 containing the address of the register to be read. Bits D7–D0 contain dummy data,
which is discarded.
_______________________________________________________________________________________
9
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
4) Take CS high (while SCLK is still high after clocking
in the last data bit), positions D7 through D0 in the
Shift register are now loaded with the register data
addressed by bits D1 through D8.
5) Take SCLK low.
6) Issue another read or write command (which can
be a No-Op), and examine the bit stream at DOUT;
the second 8 bits are the contents of the register
addressed by bits D1 through D8 in step 3.
Initial Power-Up
On initial power-up, all control registers are reset, current registers are set to minimum value, and the
MAX6957 enters shutdown mode (Table 4).
LED Current Control
LED segment drive current can be set either globally or
individually. Global control simplifies the operation
when all LEDs are set to the same current level,
because writing one register, the Global Current register, sets the current for all ports configured as LED segment drivers. It is also possible to individually control
the current drive of each LED segment driver.
Individual/global brightness control is selected by setting the configuration register I bit (Table7). The global
current register (0x02) data are then ignored, and segment currents are set using register addresses 0x12
through 0x1F (Tables 10, 11, and 12). Each segment is
controlled by a nibble of one of the 16 current registers.
Transition (Port Data Change) Detection
Port transition detection allows seven maskable ports
P24 through P30 to be continuously monitored for
changes in their logic status (Figure 6). Enable transition detection by setting the M bit in the configuration
register (Table 8) after setting the mask register. If port
31 is configured as an output (Tables 1 and 2), then
P31 automatically becomes an interrupt request (IRQ)
output to flag detected transitions. Port 31 can be configured and used as a general-purpose input port
instead if not required as the IRQ output.
The mask register determines which of the seven ports
P24 through P30 are monitored (Table 13). Set the
appropriate mask bit to enable that port for transition
detect. Clear the mask bit if transitions on that port are
to be ignored by the transition detection logic. Ports are
monitored regardless of their I/O configuration, both
input and output.
The MAX6957 maintains an internal 7-bit snapshot register to hold the comparison copy of the logic states of
ports P24 through P30. The snapshot register is updated with the condition of P24 through P31 whenever the
10
configuration register is written with the M bit set. The
update action occurs regardless of the previous state
of the M bit so that it is not necessary to clear the M bit
and then set it again to update the snapshot register.
When the data change detection bit is set, the
MAX6957 continuously compares the snapshot register
against the changing states of P24 through P31. When
a difference occurs, the IRQ bit (mask register bit D7) is
set and IRQ port P31 goes high if it is configured as an
output.
The IRQ bit and IRQ output remain set until the mask
register is next read or written, so if the IRQ is set, then
the mask register reads with bit D7 set. Writing the
mask register clears the IRQ output and resets the IRQ
bit, regardless of the value of bit D7 written.
Display Test Register
Display test mode turns on all ports configured as LED
drivers by overriding, but not altering, all controls and
port registers, except the port configuration register
(Table 14). Only ports configured as LED drivers are
affected. Ports configured as GPIO push-pull outputs
do not change state. In display test mode, each port's
current is temporarily set to 1/2 the maximum current
limit as controlled by RISET.
Selecting External Component RISET
to Set Maximum Segment Current
The MAX6957 uses an external resistor RISET to set the
maximum segment current. The recommended value,
39kΩ, sets the maximum current to 24mA, which makes
the segment current adjustable from 1.5mA to 24mA in
1.5mA steps.
To set a different segment current, use the formula:
RISET = 936kΩ / ISEG
where ISEG is the desired maximum segment current in mA.
The recommended value of RISET is 39kΩ.
The recommended value of R ISET is the minimum
allowed value, since it sets the display driver to the
maximum allowed segment current. RISET can be a
higher value to set the segment current to a lower maximum value where desired. The user must also ensure
that the maximum current specifications of the LEDs
connected to the driver are not exceeded.
The drive current for each segment can be controlled
through programming either the global current register
(Table 9) or individual segment current registers
(Tables 10, 11, and 12), according to the setting of the
current control bit of the configuration register (Table 7).
______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
REGISTER
COMMAND ADDRESS
D15
D14
D13
D12
D11
D10
D9
D8
HEX
CODE
No-Op
R/ W
0
0
0
0
0
0
0
0x00
Global Current
R/ W
0
0
0
0
0
1
0
0x02
Configuration
R/ W
0
0
0
0
1
0
0
0x04
Transition Detect Mask
R/ W
0
0
0
0
1
1
0
0x06
Display Test
R/ W
0
0
0
0
1
1
1
0x07
Port Configuration P7, P6, P5, P4
R/ W
0
0
0
1
0
0
1
0x09
Port Configuration P11, P10, P9, P8
R/ W
0
0
0
1
0
1
0
0x0A
Port Configuration P15, P14, P13, P12
R/ W
0
0
0
1
0
1
1
0x0B
Port Configuration P19, P18, P17, P16
R/ W
0
0
0
1
1
0
0
0x0C
Port Configuration P23, P22, P21, P20
R/ W
0
0
0
1
1
0
1
0x0D
Port Configuration P27, P26, P25, P24
R/ W
0
0
0
1
1
1
0
0x0E
Port Configuration P31, P30, P29, P28
R/ W
Current054
R/ W
0
0
0
0
0
1
1
0
1
0
1
1
1
0
0x0F
0x12
Current076
R/ W
0
0
1
0
0
1
1
0x13
Current098
R/ W
0
0
1
0
1
0
0
0x14
Current0BA
R/ W
0
0
1
0
1
0
1
0x15
Current0DC
R/ W
0
0
1
0
1
1
0
0x16
Current0FE
R/ W
0
0
1
0
1
1
1
0x17
Current110
R/ W
0
0
1
1
0
0
0
0x18
Current132
R/ W
0
0
1
1
0
0
1
0x19
Current154
R/ W
0
0
1
1
0
1
0
0x1A
Current176
R/ W
0
0
1
1
0
1
1
0x1B
Current198
R/ W
0
0
1
1
1
0
0
0x1C
Current1BA
R/ W
0
0
1
1
1
0
1
0x1D
Current1DC
R/ W
0
0
1
1
1
1
0
0x1E
Current1FE
R/ W
0
0
1
1
1
1
1
0x1F
Port 0 only (virtual port, no action)
R/ W
0
1
0
0
0
0
0
0x20
Port 1 only (virtual port, no action)
R/ W
0
1
0
0
0
0
1
0x21
Port 2 only (virtual port, no action)
R/ W
0
1
0
0
0
1
0
0x22
Port 3 only (virtual port, no action)
R/ W
0
1
0
0
0
1
1
0x23
Port 4 only
R/ W
0
1
0
0
1
0
0
0x24
Port 5 only
R/ W
0
1
0
0
1
0
1
0x25
Port 6 only
R/ W
0
1
0
0
1
1
0
0x26
Port 7 only
R/ W
0
1
0
0
1
1
1
0x27
Port 8 only
R/ W
0
1
0
1
0
0
0
0x28
Port 9 only
R/ W
0
1
0
1
0
0
1
0x29
Port 10 only
R/ W
0
1
0
1
0
1
0
0x2A
______________________________________________________________________________________
11
MAX6957
Table 3. Register Address Map
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 3. Register Address Map (continued)
REGISTER
COMMAND ADDRESS
HEX
CODE
D15
D14
D13
D12
D11
D10
D9
D8
Port 11 only
R/ W
0
1
0
1
0
1
1
0x2B
Port 12 only
R/ W
0
1
0
1
1
0
0
0x2C
Port 13 only
R/ W
0
1
0
1
1
0
1
0x2D
Port 14 only
R/ W
0
1
0
1
1
1
0
0x2E
Port 15 only
R/ W
0
1
0
1
1
1
1
0x2F
Port 16 only
R/ W
0
1
1
0
0
0
0
0x30
Port 17 only
R/ W
0
1
1
0
0
0
1
0x31
Port 18 only
R/ W
0
1
1
0
0
1
0
0x32
Port 19 only
R/ W
0
1
1
0
0
1
1
0x33
Port 20 only
R/ W
0
1
1
0
1
0
0
0x34
Port 21 only
R/ W
0
1
1
0
1
0
1
0x35
Port 22 only
R/ W
0
1
1
0
1
1
0
0x36
Port 23 only
R/ W
0
1
1
0
1
1
1
0x37
Port 24 only
R/ W
0
1
1
1
0
0
0
0x38
Port 25 only
R/ W
0
1
1
1
0
0
1
0x39
Port 26 only
R/ W
0
1
1
1
0
1
0
0x3A
Port 27 only
R/ W
0
1
1
1
0
1
1
0x3B
Port 28 only
R/ W
0
1
1
1
1
0
0
0x3C
Port 29 only
R/ W
0
1
1
1
1
0
1
0x3D
Port 30 only
R/ W
0
1
1
1
1
1
0
0x3E
Port 31 only
R/ W
0
1
1
1
1
1
1
0x3F
8 ports 0–7 (ports 0–3 are virtual)
R/ W
1
0
0
0
0
0
0
0x40
8 ports 1–8 (ports 1, 2, 3 are virtual)
R/ W
1
0
0
0
0
0
1
0x41
8 ports 2–9 (ports 2, 3 are virtual)
R/ W
1
0
0
0
0
1
0
0x42
8 ports 3–10 (port 3 is virtual)
R/ W
1
0
0
0
0
1
1
0x43
8 ports 4–11
R/ W
1
0
0
0
1
0
0
0x44
8 ports 5–12
R/ W
1
0
0
0
1
0
1
0x45
8 ports 6–13
R/ W
1
0
0
0
1
1
0
0x46
8 ports 7–14
R/ W
1
0
0
0
1
1
1
0x47
8 ports 8–15
R/ W
1
0
0
1
0
0
0
0x48
8 ports 9–16
R/ W
1
0
0
1
0
0
1
0x49
8 ports 10–17
R/ W
1
0
0
1
0
1
0
0x4A
8 ports 11–18
R/ W
1
0
0
1
0
1
1
0x4B
8 ports 12–19
R/ W
1
0
0
1
1
0
0
0x4C
8 ports 13–20
R/ W
1
0
0
1
1
0
1
0x4D
8 ports 14–21
R/ W
1
0
0
1
1
1
0
0x4E
8 ports 15–22
R/ W
1
0
0
1
1
1
1
0x4F
12
______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
COMMAND ADDRESS
D15
D14
D13
D12
D11
D10
D9
D8
HEX
CODE
8 ports 16–23
R/ W
1
0
1
0
0
0
0
0x50
8 ports 17–24
R/ W
1
0
1
0
0
0
1
0x51
8 ports 18–25
R/ W
1
0
1
0
0
1
0
0x52
8 ports 19–26
R/ W
1
0
1
0
0
1
1
0x53
8 ports 20–27
R/ W
1
0
1
0
1
0
0
0x54
8 ports 21–28
R/ W
1
0
1
0
1
0
1
0x55
8 ports 22–29
R/ W
1
0
1
0
1
1
0
0x56
8 ports 23–30
R/ W
1
0
1
0
1
1
1
0x57
8 ports 24–31
R/ W
1
0
1
1
0
0
0
0x58
7 ports 25–31
R/ W
1
0
1
1
0
0
1
0x59
6 ports 26–31
R/ W
1
0
1
1
0
1
0
0x5A
5 ports 27–31
R/ W
1
0
1
1
0
1
1
0x5B
4 ports 28–31
R/ W
1
0
1
1
1
0
0
0x5C
3 ports 29, 30, 31
R/ W
1
0
1
1
1
0
1
0x5D
2 ports 30, 31
R/ W
1
0
1
1
1
1
0
0x5E
1 port 31 only
R/ W
1
0
1
1
1
1
1
0x5F
REGISTER
Note: Unused bits read as 0.
These registers select the LED’s constant-current drive
from 16 equal fractions of the maximum segment current. The current difference between successive current steps, I STEP , is therefore determined by the
formula:
ISTEP = ISEG / 16
If ISEG = 24mA, then ISTEP = 24mA / 16 = 1.5mA.
Applications Information
Driving Bicolor and Tricolor LEDs
Bicolor digits group a red and a green die together for
each display element, so that the element can be lit
red, green (or orange), depending on which die (or
both) is lit. The MAX6957 allows each segment's current to be set individually from 1/16th (minimum current
and LED intensity) to 16/16th (maximum current and
LED intensity), as well as off (zero current). Thus, a
bicolor (red-green) segment pair can be set to 289
color/intensity combinations. A discrete or CA tricolor
(red-green-yellow or red-green-blue) segment triad can
be set to 4913 color/intensity combinations.
Power Dissipation Issues
Each MAX6957 port can sink a current of 24mA into an
LED with a 2.4V forward-voltage drop when operated
from a supply voltage of at least 3.0V. The minimum
voltage drop across the internal LED drivers is therefore (3.0V - 2.4V) = 0.6V. The MAX6957 can sink 28 x
24mA = 672mA when all outputs are operating as LED
segment drivers at full current. On a 3.3V supply, a
MAX6957 dissipates (3.3V - 2.4V) ✕ 672mA = 0.6W
when driving 28 of these 2.4V forward-voltage drop
LEDs at full current. This dissipation is within the ratings
of the 36-pin SSOP package with an ambient temperature up to +98°C. If a higher supply voltage is used or
the LEDs used have a lower forward-voltage drop than
2.4V, the MAX6957 absorbs a higher voltage, and the
MAX6957's power dissipation increases.
If the application requires high drive current and high
supply voltage, consider adding a series resistor to
each LED to drop excessive drive voltage off-chip. For
example, consider the requirement that the MAX6957
must drive LEDs with a 2.0V to 2.4V specified forwardvoltage drop, from an input supply range is 5V ±5%
with a maximum LED current of 20mA. Minimum input
supply voltage is 4.75V. Maximum LED series resistor
______________________________________________________________________________________
13
MAX6957
Table 3. Register Address Map (continued)
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
GPIO INPUT
CONDITIONING
GPIO IN
GPIO/PORT
OUTPUT LATCH
GPIO/PORT OUT
IRQ STATUS STORED AS MSB OF MASK REGISTER
P31
IRQ
OUTPUT LATCH
CLOCK PULSE AFTER EACH READ ACCESS TO MASK REGISTER
R
S
CONTROL REGISTER M BIT = 1
GPIO INPUT
CONDITIONING
P30
GPIO IN
D
Q
GPIO/PORT OUT
MASK REGISTER BIT 6
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P29
GPIO IN
D
Q
GPIO/PORT OUT
MASK REGISTER BIT 5
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P28
GPIO IN
D
Q
GPIO/PORT OUT
MASK REGISTER BIT 4
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P27
GPIO IN
D
Q
OR
MASK REGISTER BIT 3
GPIO/PORT OUT
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P26
GPIO IN
D
Q
GPIO/PORT OUT
MASK REGISTER BIT 2
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P25
GPIO IN
D
Q
GPIO/PORT OUT
MASK REGISTER BIT 1
GPIO/PORT OUTPUT LATCH
GPIO INPUT
CONDITIONING
P24
GPIO IN
D
GPIO/PORT OUT
GPIO/PORT OUTPUT LATCH
Q
MASK REGISTER LSB
CLOCK PULSE WHEN WRITING CONFIGURATION REGISTER WITH M BIT SET
Figure 6. Maskable GPIO Ports P24 Through P31
14
______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
POWER-UP CONDITION
ADDRESS
CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
LED Off; GPIO Output Low
0x24 to
0x3F
X
X
X
X
X
X
X
0
1/16 (minimum on)
0x02
X
X
X
X
0
0
0
0
Shutdown Enabled
Current Control = Global
Transition Detection Disabled
0x04
0
0
X
X
X
X
X
0
Input Mask
Register
All Clear (Masked Off)
0x06
X
0
0
0
0
0
0
0
Display Test
Normal Operation
0x07
X
X
X
X
X
X
X
0
Port
Configuration
P7, P6, P5, P4: GPIO Inputs Without Pullup
0x09
1
0
1
0
1
0
1
0
Port
Configuration
P11, P10, P9, P8: GPIO Inputs Without Pullup
0x0A
1
0
1
0
1
0
1
0
Port
Configuration
P15, P14, P13, P12: GPIO Inputs Without Pullup
0x0B
1
0
1
0
1
0
1
0
Port
Configuration
P19, P18, P17, P16: GPIO Inputs Without Pullup
0x0C
1
0
1
0
1
0
1
0
Port
Configuration
P23, P22, P21, P20: GPIO Inputs Without Pullup
0x0D
1
0
1
0
1
0
1
0
Port
Configuration
P27, P26, P25, P24: GPIO Inputs Without Pullup
0x0E
1
0
1
0
1
0
1
0
Port
Configuration
P31, P30, P29, P28: GPIO Inputs Without Pullup
0x0F
1
0
1
0
1
0
1
0
Current054
1/16 (minimum on)
0x12
0
0
0
0
0
0
0
0
Current076
1/16 (minimum on)
0x13
0
0
0
0
0
0
0
0
Current098
1/16 (minimum on)
0x14
0
0
0
0
0
0
0
0
Current0BA
1/16 (minimum on)
0x15
0
0
0
0
0
0
0
0
Current0DC
1/16 (minimum on)
0x16
0
0
0
0
0
0
0
0
Current0FE
1/16 (minimum on)
0x17
0
0
0
0
0
0
0
0
Current110
1/16 (minimum on)
0x18
0
0
0
0
0
0
0
0
Current132
1/16 (minimum on)
0x19
0
0
0
0
0
0
0
0
Current154
1/16 (minimum on)
0x1A
0
0
0
0
0
0
0
0
Current176
1/16 (minimum on)
0x1B
0
0
0
0
0
0
0
0
REGISTER
FUNCTION
Port Register
Bits 4 to 31
Global
Current
Configuration
Register
REGISTER DATA
Current198
1/16 (minimum on)
0x1C
0
0
0
0
0
0
0
0
Current1BA
1/16 (minimum on)
0x1D
0
0
0
0
0
0
0
0
Current1DC
1/16 (minimum on)
0x1E
0
0
0
0
0
0
0
0
Current1FE
1/16 (minimum on)
0x1F
0
0
0
0
0
0
0
0
X = unused bits; if read, zero results.
______________________________________________________________________________________
15
MAX6957
Table 4. Power-Up Configuration
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 5. Configuration Register Format
REGISTER DATA
FUNCTION
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Configuration Register
0x04
M
I
X
X
X
X
X
S
X = Don’t care bit.
Table 6. Shutdown Control (S Data Bit D0) Format
REGISTER DATA
FUNCTION
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Shutdown
0x04
M
I
X
X
X
X
X
0
Normal Operation
0x04
M
I
X
X
X
X
X
1
X = Don’t care bit.
Table 7. Global Current Control (I Data Bit D6) Format
REGISTER DATA
FUNCTION
ADDRESS
CODE (HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Global
Constant-current limits for all digits are
controlled by one setting in the Global Current
register, 0x02
0x04
M
0
X
X
X
X
X
S
Individual Segment
Constant-current limit for each digit is
individually controlled by the settings in the
Current054 through Current1FE registers
0x04
M
1
X
X
X
X
X
S
X = Don’t care bit.
Table 8. Transition Detection Control (M-Data Bit D7) Format
REGISTER DATA
FUNCTION
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Disabled
0x04
0
I
X
X
X
X
X
S
Enabled
X = Don’t care bit.
0x04
1
I
X
X
X
X
X
S
Table 9. Global Segment Current Register Format
LED DRIVE
FRACTION
TYPICAL SEGMENT
CURRENT (mA)
ADDRESS
CODE (HEX)
D7
D6
D5
D4
D3
D2
D1
D0
HEX CODE
1/16
1.5
0x02
X
X
X
X
0
0
0
0
0xX0
2/16
3
0x02
X
X
X
X
0
0
0
1
0xX1
3/16
4.5
0x02
X
X
X
X
0
0
1
0
0xX2
4/16
6
0x02
X
X
X
X
0
0
1
1
0xX3
5/16
7.5
0x02
X
X
X
X
0
1
0
0
0xX4
X = Don’t care bit.
16
______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
LED DRIVE
FRACTION
TYPICAL SEGMENT
CURRENT (mA)
ADDRESS
CODE (HEX)
D7
D6
D5
D4
D3
D2
D1
D0
HEX CODE
6/16
9
0x02
X
X
X
X
0
1
0
1
0xX5
7/16
10.5
0x02
X
X
X
X
0
1
1
0
0xX6
8/16
12
0x02
X
X
X
X
0
1
1
1
0xX7
9/16
13.5
0x02
X
X
X
X
1
0
0
0
0xX8
10/16
15
0x02
X
X
X
X
1
0
0
1
0xX9
11/16
16.5
0x02
X
X
X
X
1
0
1
0
0xXA
12/16
18
0x02
X
X
X
X
1
0
1
1
0xXB
13/16
19.5
0x02
X
X
X
X
1
1
0
0
0xXC
14/16
21
0x02
X
X
X
X
1
1
0
1
0xXD
15/16
22.5
0x02
X
X
X
X
1
1
1
0
0xXE
16/16
24
0x02
X
X
X
X
1
1
1
1
0xXF
X = Don’t care bit.
Table 10. Individual Segment Current Registers
REGISTER
FUNCTION
ADDRESS
CODE (HEX)
Current054 register
0x12
Segment 5
Segment 4
Current076 register
0x13
Segment 7
Segment 6
Current098 register
0x14
Segment 9
Segment 8
Segment 10
D7
D6
D5
D4
D3
D2
D1
Current0BA register
0x15
Segment 11
Current0DC register
0x16
Segment 13
Segment 12
Current0FE register
0x17
Segment 15
Segment 14
Current110 register
0x18
Segment 17
Segment 16
Current132 register
0x19
Segment 19
Segment 18
Current154 register
0x1A
Segment 21
Segment 20
Current176 register
0x1B
Segment 23
Segment 22
Segment 24
Current198 register
0x1C
Segment 25
Current1BA register
0x1D
Segment 27
Segment 26
Current1DC register
0x1E
Segment 29
Segment 28
Current1FE register
0x1F
Segment 31
Segment 30
D0
______________________________________________________________________________________
17
MAX6957
Table 9. Global Segment Current Register Format (continued)
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
Table 11. Even Individual Segment Current Format
LED DRIVE
FRACTION
SEGMENT
CONSTANT
CURRENT WITH
RISET = 39kΩ (mA)
ADDRESS
CODE (HEX)
1/16
1.5
2/16
3
3/16
4/16
5/16
D7
D6
D5
D3
D2
D1
D0
HEX CODE
0x12 to 0x1F
0
0
0
0
0xX0
0x12 to 0x1F
0
0
0
1
0xX1
4.5
0x12 to 0x1F
0
0
1
0
0xX2
6
0x12 to 0x1F
0
0
1
1
0xX3
7.5
0x12 to 0x1F
0
1
0
0
0xX4
6/16
9
0x12 to 0x1F
0
1
0
1
0xX5
7/16
10.5
0x12 to 0x1F
0
1
1
0
0xX6
8/16
12
0x12 to 0x1F
0
1
1
1
0xX7
0xX8
See Table 12.
D4
9/16
13.5
0x12 to 0x1F
1
0
0
0
10/16
15
0x12 to 0x1F
1
0
0
1
0xX9
11/16
16.5
0x12 to 0x1F
1
0
1
0
0xXA
12/16
18
0x12 to 0x1F
1
0
1
1
0xXB
13/16
19.5
0x12 to 0x1F
1
1
0
0
0xXC
14/16
21
0x12 to 0x1F
1
1
0
1
0xXD
15/16
22.5
0x12 to 0x1F
1
1
1
0
0xXE
16/16
24
0x12 to 0x1F
1
1
1
1
0xXF
value is (4.75V - 2.4V - 0.6V)/0.020A = 87.5Ω. We
choose 82Ω ±2%. Worst-case resistor dissipation is at
maximum toleranced resistance, i.e., (0.020A)2 ✕ (82Ω
✕ 1.02) = 34mW. The maximum MAX6957 dissipation
per LED is at maximum input supply voltage, minimum
toleranced resistance, minimum toleranced LED forward-voltage drop, i.e., 0.020 x (5.25V - 2.0V - (0.020A
✕ 82Ω x 0.98)) = 32.86mW. Worst-case MAX6957 dissipation is 920mW, driving all 28 LEDs at 20mA full current at once, which meets the 941mW dissipation
ratings of the 36-pin SSOP package.
Power-Supply Considerations
The MAX6957 operates with power-supply voltages of
2.5V to 5.5V. Bypass the power supply to GND with a
0.047µF capacitor as close to the device as possible.
Add a 1µF capacitor if the MAX6957 is far away from
the board's input bulk decoupling capacitor.
Low-Voltage Operation
The MAX6957 operates down to 2V supply voltage
(although the sourcing and sinking currents are not
guaranteed), providing that the MAX6957 is powered
up initially to at least 2.5V to trigger the device's internal
reset, and also that the serial interface is constrained to
10Mbps.
18
______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
LED
DRIVE
FRACTION
SEGMENT
CONSTANT
CURRENT WITH
RISET = 39kΩ (mA)
ADDRESS
CODE (HEX)
D7
D6
D5
D4
1/16
1.5
0x12 to 0x1F
0
0
0
0
0x0X
D3
D2
D1
D0
HEX CODE
2/16
3
0x12 to 0x1F
0
0
0
1
0x1X
3/16
4.5
0x12 to 0x1F
0
0
1
0
0x2X
4/16
6
0x12 to 0x1F
0
0
1
1
0x3X
5/16
7.5
0x12 to 0x1F
0
1
0
0
0x4X
6/16
9
0x12 to 0x1F
0
1
0
1
0x5X
7/16
10.5
0x12 to 0x1F
0
1
1
0
0x6X
8/16
12
0x12 to 0x1F
0
1
1
1
9/16
13.5
0x12 to 0x1F
1
0
0
0
0x8X
10/16
15
0x12 to 0x1F
1
0
0
1
0x9X
11/16
16.5
0x12 to 0x1F
1
0
1
0
0xAX
12/16
18
0x12 to 0x1F
1
0
1
1
0xBX
13/16
19.5
0x12 to 0x1F
1
1
0
0
0xCX
14/16
21
0x12 to 0x1F
1
1
0
1
0xDX
15/16
22.5
0x12 to 0x1F
1
1
1
0
0xEX
16/16
24
0x12 to 0x1F
1
1
1
1
0xFX
See Table 11.
0x7X
X = Don’t care bit.
Table 13. Transition Detection Mask Register
FUNCTION
Read Mask
Register
REGISTER
ADDRESS
(HEX)
REGISTER DATA
READ/
WRITE
D7
D6
D5
D4
D3
D2
D1
D0
Read
IRQ Status*
Write
Unchanged
Port
30
mask
Port
29
mask
Port
28
mask
Port
27
mask
Port
26
mask
Port
25
mask
Port
24
mask
0x06
*IRQ is automatically cleared after it is read.
Table 14. Display Test Register
REGISTER DATA
MODE
ADDRESS CODE
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
Normal Operation
0x07
X
X
X
X
X
X
X
0
Display Test Mode
0x07
X
X
X
X
X
X
X
1
X = Don’t care bit.
______________________________________________________________________________________
19
MAX6957
Table 12. Odd Individual Segment Current Format
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
MAX6957
Pin Configurations (continued)
Chip Information
TRANSISTOR COUNT: 30,316
PROCESS: CMOS
TOP VIEW
ISET
1
36 V+
GND
2
35 CS
GND
3
34 DIN
33 SCLK
DOUT 4
P8
32 P4
5
31 P31
P12 6
P9
30 P5
7
P13 8
P10 9
29 P30
MAX6957
28 P6
P14 10
27 P29
P11 11
26 P7
P15 12
25 P28
P16 13
24 P27
P17 14
23 P26
P18 15
22 P25
P19 16
21 P24
P20 17
20 P23
P21 18
19 P22
SSOP
20
______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
3V
3V
36 V+
47nF
3 GND
2 GND
1 ISET
39kΩ
34 DIN
33 SCLK
35 CS
4-WIRE DATA IN
4-WIRE CLOCK IN
CHIP SELECT
4 DOUT
U1
MAX6957AAX
P4 32
P5 30
P6 28
P7 26
a1
a2
P8 5
P9 7
P10 9
P11 11
d1
d2
e
P12 6
P13 8
P14 10
P15 12
31 P31
29 P30
27 P29
25 P28
24 P27
P16 13
P17 14
P18 15
P19 16
P20 17
23 P26
22 P25
21 P24
P21 18
P22 19
P23 20
LED1
b
c
f
g1
g2
h
i
j
k
l
m
dp
ca
a1
a2
LED2
b
c
d1
d2
e
f
g1
g2
h
i
3V
36 V+
47nF
3 GND
2 GND
1 ISET
39kΩ
34 DIN
33 SCLK
35 CS
4 DOUT
4-WIRE DATA OUT
IRQ OUT
1
SW1
SW2
2
SW3
U2
MAX6957AAX
32
P4
30
P5
28
P6
26
P7
5
P8
7
P9
P10 9
P11 11
P12 6
P13 8
P14 10
P15 12
31 P31
29 P30
27 P29
25 P28
24 P27
P16 13
P17 14
P18 15
P19 16
P20 17
23 P26
22 P25
21
P24
P21 18
P22 19
P23 20
j
k
l
m
dp
ca
a1
a2
LED3
b
c
d1
d2
e
f
g1
g2
h
i
j
k
l
m
dp
ca
______________________________________________________________________________________
21
MAX6957
Typical Operating Circuit
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
SSOP.EPS
MAX6957
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
22
______________________________________________________________________________________
4-Wire-Interfaced, 2.5V to 5.5V, 20-Port and
28-Port LED Display Driver and I/O Expander
SSOP.EPS
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 23
© 2002 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
MAX6957
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)