CLOCK OSCILLATORS Logic: HCMOS “H32” series 3.2x2.5x1.1 mm; Wave Form: Square wave MERCURY Since 1973 ● Suitable for light weight and compact consumer electronic devices ● Ideal for high density boards ● Mercury’s smallest footprint clock oscillators. ● RoHS compliant and lead-free product General Specifications TA=+25°C, VDD at specified voltage, CL=15 pF VDD = +3.3 V D.C. ±5% VDD = +5.0 V D.C. ±5% 25H32 3H32 5H32 16.0 MHz ~44.0 MHz HCMOS 90% VDD min. 10% VDD max. Input Voltage (VDD) Mercury Model Frequency Range Output Logic Output Voltage HIGH “1” Output Voltage LOW “0” Rise Time / Fall Time (0.1VDD ↔ 0.9 VDD) Output Load 10 n sec. max.. Current Consumption Frequency Stability(1) Commercial (0°C to +70°C) Temperature code is ‘C” Wider Commercial Range: (-20°C to +70°C) T 15 pF 5 mA max. at 20 MHz 9 mA max. at 16 MHz 12 mA max. at 16 MHz 9 mA max. at 40 MHz 12 mA max. at 40 MHz. 20 mA max. at 40 MHz Stability code “A”:±25 ppm over 0°C to +70°C Stability code “B”:±50 ppm over 0°C to +70°C Stability code “C”: ±100 ppm over 0°C to +70°C”) If non-standard please enter the desired stability after the “C”. For example “C20” represents ±20 ppm over 0 to +70°C Stability code “G”:±25 ppm over -20°C to +70°C Stability code “H”:±50 ppm over -20°C to +70°C Stability code “J”:±100 ppm over -20°C to +70°C Duty Cycle (symmetry) Standard: 50%±10%. Option: 50%±5%. At 50% VDD 10 m sec. max. Start-up Time (Ts) 10 p sec. typical Phase Jitter RMS If no connection or voltage of 2.2 V or greater is applied to pad No. 1.: The output is active If voltage of 0.8 V or lower is applied to pad 1: The output is high impedance. Pin 1 Enable Disable Delay Time is 100 n sec. max.. Aging ±5 ppm first year max. At +25°C 178 mm reel; 8 mm tape; 1000 pcs per reel. Packaging (1) Inclusive of 25°C tolerance, operating temperature range, ±10% input voltage variation, load change, aging, shock and vibration. MERCURY www.mercury-crystal.com Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: [email protected] U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected] MERCURY Page 1 of 3 Date: Nov. 23, 2005 Rev. 0 CLOCK OSCILLATORS Logic: HCMOS “H32” series 3.2x2.5x1.1 mm; Wave Form: Square wave MERCURY Since 1973 Environment Performance Specifications Green Requirement Storage temp. range Humidity Hermetic seal Solderability Reflow Vibration Shock MIL-0-55310 RoHS compliant; Pb-free product -50 to +125°C 85% RH, 85°C, 48 hours Lead rate 2x10-8 ATM-cm3/sec max. MIL-STD-202F method 208E 260°C for 10 sec. MIL-STD-202F method 204, 35G, 50 to 2000 Hz MIL-STD-202F method 213B, test condi. E, 1000GG ½ sine wave Exceeds environmental and electrical spec. of equivalent MIL-0-55310 Part Number Format and Example: Example: 3H32-AT-16.000-S Explanation: H32 clock oscillator with pad 1 Tri-state, +3.3 V supply voltage, ±25 ppm frequency stability over 0 to +70°C, 16.000 MHz, duty cycle is 45% / 55%. " 3 H32 — " " A T — " " 16.000 r S n o p q s n: Voltage codes: “25” for +2.5 V; “3” for +3.3 V ; “5” for +5 V o: Product series p: Frequency stability code: “A” ~ “J” or custom. See table above. q: “T”: Tri-state option on pad 1 (Tri-state option is standard if not specified), leave blank if tri-state is not required r Frequency in MHz s: “S” for 45% / 55% duty cycle option. Leave blank if duty cycle is 40% / 60% (standard). H32 OUTPUT WAVEFORM: Tr H32 Test Circuit: Tf VOH 90% Vcc i VOL 10% Vcc max. TH T Duty Cycle = (TH / T)x100% MERCURY Page 2 of 3 Date: Nov. 23, 2005 Rev. 0 CLOCK OSCILLATORS Logic: HCMOS “H32” series 3.2x2.5x1.1 mm; Wave Form: Square wave H32 Package Dimensions and Recommended Pad Layout: H32 Tape and Reel Dimensions unit: mm MERCURY Since 1973 unit mm[inches] Reflow Soldering Condition 1000 pcs per reel MERCURY Page 1 of 3 Date: Nov. 23, 2005 Rev. 0