CLOCK OSCILLATORS “H53” series 5x3.2 mm Logic: HCMOS Wave Form: Square wave MERCURY Since 1973 H53 (5x3.2x1.2 mm) is Mercury smallest footprint and lowest profile SMD clock oscillators. Its applications include PDAs, ATM, PCMCOA, networking, laptops, digital camera, wireless LAN and disk and tape drives. Output is TTL/CMOS compatible and Tri-state enable/disable is standard on pad 1. General Specifications TA=+25°C, VDD at specified voltage, CL=15 pF Input Voltage (VDD) Mercury Model Frequency Range Output Logic Output Voltage HIGH “1” Output Voltage LOW “0” Rise Time / Fall Time (0.1VDD ↔ 0.9 VDD) Output Load VDD = +3.3 V D.C. ±10% VDD =+5.0 V D.C.±10% 3H53 5H53 2.5 MHz ~66.0 MHz HCMOS 2.97 V min. 4.5 V min. 0.33 V max. 0.5 V max. 5 n sec. max. 7 n sec. max. 15 pF 2.5 ~19.9 MHz: 8 mA max. 2.5 ~19.9 MHz: 15 mA max. 20.0 ~40.0 MHz: 15 mA max. 20.0 ~40.0 MHz: 25 mA max. Current Consumption 40.1 ~59.9 MHz: 22 mA max. 40.1 ~59.9 MHz: 40 mA max. 60.0 ~66.0 MHz: 25 mA max. 60.0 ~66.0 MHz: 45 mA max. Commercial Stability code “A”:±25 ppm over 0°C to +70°C (0°C to +70°C) Stability code “B”:±50 ppm over 0°C to +70°C Temperature code Stability code “C”: ±100 ppm over 0°C to +70°C”) Frequency is ‘C” If non-standard please enter the desired stability after the “C”. Stability(1) For example “C20” represents ±20 ppm over 0 to +70°C Stability code “D”:±25 ppm over -40°C to +85°C Industrial Stability code “E”:±50 ppm over -40°C to +85°C (-40°C to +85°C) Stability code “F”:±100 ppm over -40°C to +85°C Temperature code If non-standard please enter the desired stability after the “I”. is ‘I” For example “I20” represents ±20 ppm over -40 to +85°C Standard: 50%±10%. Duty Cycle (symmetry) Option: 50±5% 2.5 ~ 32 MHz: 5 m sec. max. Start-up Time (Ts) 32+MHz: 10 m sec. max. Phase Jitter RMS 10 p sec. typical If no connection or voltage of 2.2V or greater is applied to pad No. 1.: The output is active If voltage of 0.8V or lower is applied to pad 1: The output is high impedance Pin 1 Internal 10K ohms pull-up resistor Disable time is 100 n sec. max.; Enable time is 100 m sec. max. Storage Temperature -50°C to +100°C Aging ±5 ppm per year max. (1) Inclusive of 25°C tolerance, operating temperature range, ±10% input voltage variation, load change, aging, shock and vibration. MERCURY www.mercury-crystal.com Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: [email protected] U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: [email protected] MERCURY Page 1 of 3 Date: July. 25, 2007 Rev. 2 CLOCK OSCILLATORS “H53” series 5x3.2 mm Logic: HCMOS Wave Form: Square wave MERCURY Since 1973 Environment Performance Specifications Green Requirement Storage temp. range Humidity Hermetic seal Solderability Reflow Vibration Shock MIL-0-55310 Packaging RoHS compliant; Pb-free product -55 to +125°C 85% RH, 85°C, 48 hours Lead rate 2x10-8 ATM-cm3/sec max. MIL-STD-202F method 208E 260°C for 10 sec. MIL-STD-202F method 204, 35G, 50 to 2000 Hz MIL-STD-202F method 213B, test condi. E, 1000GG ½ sine wave Exceeds environmental and electrical spec. of equivalent MIL-0-55310 12 mm tape and reel; 1000 pcs /reel Part Number Format and Example: Example: 3H53-AT-13.000-S Explanation: H53 clock oscillator with pad 1 Tri-state, +3.3 V supply voltage, ±25 ppm frequency stability over 0 to +70°C, 13.000 MHz, duty cycle is 45% / 55%. " " " " " — A — 13.000 S H53 T n o p q s r n: Voltage codes: “3” for +3.3 V; “5” for +5.0 V o: Product series p: Frequency stability code: “A” ~ “F” or custom. See table above. q: “T”: Tri-state option on pad 1 (Tri-state option is standard if not specified), leave blank if tri-state is not required r Frequency in MHz s: “S” as prefix for 45% / 55% duty cycle option. Leave blank if duty cycle is 40% / 60% (standard). 3 H53 Test Circuit: H53 OUTPUT WAVEFORM: Tr Tf VOH 90% Vcc i VOL 10% Vcc max. TH T Duty Cycle = (TH / T)x100% MERCURY Page 2 of 3 Date: July. 25, 2007 Rev. 2 CLOCK OSCILLATORS “H53” series 5x3.2 mm Logic: HCMOS Wave Form: Square wave _ H53 _ 3 MEC 1 2 2 1.2[0.047] 2.2[0.087] 1.4[0.055] Since 1973 unit mm[inches] 1.20±0.10[0.047±0.004] 4 Pad 1 Pad 2 Pad 3 Pad 4 Tri-State Ground Output Supply voltage 1 2.54[0.100]typ. bottom view 0.75[0.030] [0.197±0.006] 5.00±0.15 4 3 [0.047±0.004] 1.20±0.1 [0.126±0.006] 3.2±0.15 H53 Package Dimensions and Recommended Pad Layout: MERCURY 1.2±0.1 [0.047±0.004] 2.54[0.100] Chamfered pad is pad No. 1. Count counter-clockwise when looking at top view. Count clockwise when looking at bottom view. H53 Tape and Reel Dimensions unit: mm Reflow Soldering Condition 1000 pcs per reel MERCURY Page 1 of 3 Date: July. 25, 2007 Rev. 2