D100E Series Low Cost, 1W SIP Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: Parameter Conditions • 1W Output Power • Miniature SIP Case • UL Approved (File E245422) Input Voltage Range • Single & Dual Outputs Input Filter Reverse Polarity Input Current • 1,000 VDC Isolation Output • >3.5 MHour MTBF Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation, See Note 1 Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit • 24 Standard Models • LOWEST COST!! Min. Typ. 5 VDC Input 4.5 5.0 12 VDC Input 10.8 12.0 24 VDC Input 21.6 24.0 Internal Capacitor Conditions Min. Typ. ±1.0 Dual Output , Balanced Loads ±0.1 For Vin Change of 1% ±1.2 See Model Selection Guide See Note 2 50 120 ±0.02 Momentary (1.0 Sec.) Max. 5.5 13.2 26.4 Units 0.3 A Max. ±3.0 ±1.0 Units % % % 75 mV P - P % %/ºC ±0.03 VDC General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 Typ. Max. Units VDC M pF kHz Max. +85 +125 Units ºC ºC 95 % 60 100 Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient 0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Reliability Specifications MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Parameter MTBF Safety Standards Safety Approvals Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. Typ. Max. Units 3.5 MHours UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Absolute Maximum Ratings T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 300 450 Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com Units VDC ºC mW www.micropowerdirect.com Model Selection Guide Model Number D101E D102E D103E D104E D105E D106E D107E D108E D111E D112E D113E D114E D115E D116E D117E D118E D121E D122E D123E D124E D125E D126E D127E D128E Input Voltage (VDC) Current (mA) Voltage Nominal Range Full-Load No-Load (VDC) 5 4.5 - 5.5 278 30 5.0 5 4.5 - 5.5 270 30 9.0 5 4.5 - 5.5 260 30 12.0 5 4.5 - 5.5 253 30 15.0 5 4.5 - 5.5 278 30 ±5.0 5 4.5 - 5.5 267 30 ±9.0 5 4.5 - 5.5 256 30 ±12.0 5 4.5 - 5.5 253 30 ±15.0 12 10.8 - 13.2 114 15 5.0 12 10.8 - 13.2 111 15 9.0 12 10.8 - 13.2 105 15 12.0 12 10.8 - 13.2 104 15 15.0 12 10.8 - 13.2 113 15 ±5.0 12 10.8 - 13.2 110 15 ±9.0 12 10.8 - 13.2 105 15 ±12.0 12 10.8 - 13.2 104 15 ±15.0 24 21.6 - 26.4 56 8 5.0 24 21.6 - 26.4 55 8 9.0 24 21.6 - 26.4 52 8 12.0 24 21.6 - 26.4 51 8 15.0 24 21.6 - 26.4 56 8 ±5.0 24 21.6 - 26.4 55 8 ±9.0 24 21.6 - 26.4 52 8 ±12.0 24 21.6 - 26.4 51 8 ±15.0 Output Current Current Load Regulation (mA, Max) (mA, Min) (%, Max) 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 Rating Efficiency Fuse Slow-Blow (%, Typ) (mA) 72 74 77 79 72 75 78 79 73 75 79 80 74 76 79 80 74 76 80 81 74 76 80 81 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 100 100 100 100 100 100 100 100 Derating Curve Other input/output combinations are available (i.e. 3.3 VDC). Contact the factory for details at: [email protected] Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at noload may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input Output Capacitor Input capacitor will enhance Vin Vout Capacitor stability over temperature Single Dual and input line variations. 5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF Recommended capacitor 9 VDC 4.7 µF 2.2 µF values are given in the 12 VDC 2.2 µF table above. For applica- 24 VDC 1.0 µF 12 VDC 2.2 µF 1.0 µF tions requiring very low 15 VDC 1.0 µF 0.47 µF output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Mechanical Dimensions Pin Connections Pin Single Dual Pin Single Dual 1 2 4 +Vin -Vin -Vout +Vin -Vin -Vout 5 6 No Pin +Vout Common +Vout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]