D100EHI Series Low Cost, Miniature SIP 1W, Very High Isolation DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power • 6,000 VDC Isolation • 7 Pin SIP Case • 5V and 12V Inputs • Single & Dual Outputs • 16 Standard Models • Short Circuit Protected (12V Units) • 3.5 MH MTBF • LOWEST COST!! Input Parameter Conditions Input Voltage Range Min. Typ. Max. 5 VDC Input 4.5 5.0 5.5 12 VDC Input 10.8 12.0 13.2 Typ. Max. Input Filter Units VDC Internal Capacitor Output Parameter Conditions Min. Output Voltage Accuracy ±2.0 Output Voltage Balance Dual Output , Balanced Loads Line Regulation Load Regulation, See Note 1 Ripple & Noise (20 MHz) % ±1.2 5V Output ±12.8 ±15 9V Output ±8.3 ±15 12V Output ±6.8 ±15 24V Output ±6.3 ±15 See Note 2 150 Temperature Coefficient Output Short Circuit % ±2.0 For Vin Change of 1% Units %/% % 200 mV P - P ±0.03 %/ºC 5 VDC Input Momentary (1.0 Seconds) 12 VDC Input Continuous (Autorecovery) General Parameter Conditions Isolation Voltage Isolation Resistance Isolation Capacitance Min. Typ. Units 6,000 VDC 500 VDC 1,000 M 100 kHz, 1V Switching Frequency Max. 60 Seconds 10 5 VDC Input 250 12 VDC Input 50 pF kHz Environmental Parameter Conditions Operating Temperature Range Min. Ambient Storage Temperature Range Cooling Max. Units -40 Typ. +85 ºC -55 +125 ºC 95 % Free Air Convection Humidity RH, Non-condensing Physical Case Size MicroPower Direct Case Material 292 Page Street Suite D Stoughton, MA 02072 USA Weight 0.77 x 0.38 x 0.50 Inches (19.5 x 9.8 x 12.5 mm) Non-Conductive Black Plastic (UL94-V0) 0.42 Oz (12g) Reliability Specifications Parameter Conditions MTBF T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Min. MIL HDBK 217F, 25ºC, Gnd Benign Typ. Max. 3.5 Units MHours Absolute Maximum Ratings Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature Min. Typ. -0.7 7.5 12 VDC Input -0.7 15.0 1.5 mm From Case For 10 Sec. Internal Power Dissipation Max. 5 VDC Input All Models VDC 300 ºC 1,500 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com Units www.micropowerdirect.com Model Selection Guide Input Model Number D101EHI D102EHI D103EHI D104EHI D105EHI D106EHI D107EHI D108EHI D111EHI D112EHI D113EHI D114EHI D115EHI D116EHI D117EHI D118EHI Voltage (VDC) Output Current (mA) Voltage Current Current (mA, Max) (mA, Min) Nominal Range Full-Load No-Load (VDC) 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 10.8 - 13.2 286 278 274 270 286 278 274 266 119 117 116 113 119 117 116 111 60 60 60 60 60 60 60 60 40 40 40 40 40 40 40 40 5.0 9.0 12.0 15.0 ±5.0 ±9.0 ±12.0 ±15.0 5.0 9.0 12.0 15.0 ±5.0 ±9.0 ±12.0 ±15.0 Input Capacitor 5 VDC 4.7 µF 12 VDC 2.2 µF Single Output Vout Capacitor 5 VDC 10.0 µF 9 VDC 4.7 µF 12 VDC 2.2 µF 15 VDC 1.0 µF 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 (mA) 70 72 73 74 70 72 73 75 70 71 72 74 70 71 72 74 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 250 250 250 250 250 250 250 250 Derating Curve Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhance stability over temperature and input line variations. Recommended capacitor values are given in the table below. Vin 200 111 84 67 ±100 ±56 ±42 ±33 200 111 84 67 ±100 ±56 ±42 ±33 Rating Efficiency Fuse Slow-Blow (%, Typ) Dual Output Vout Capacitor ±5 VDC 4.7 µF ±9 VDC 2.2 µF ±12 VDC 1.0 µF ±15 VDC 1.0 µF For applications requiring very low output noise levels, a simple Pi filter should be effective. Component values would depend upon the application, but capacitor values of 4.7 µF and inductor values of 10 µH are often sufficient. 3. These units should not be operated with a load under 10% of full load. Operation at no-load will not cause damage to the unit, but it is not recommended. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Mechanical Dimensions Pin Connections Pin Single Dual 1 2 5 6 7 +Vin -Vin -Vout No Pin +Vout +Vin -Vin -Vout Common +Vout Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]