D100ER Series Low Cost, 1W SIP Tightly Regulated DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: Parameter Conditions Min. Typ. Max. 5 VDC Input 4.75 5.0 5.25 12 VDC Input 11.4 12.0 12.6 24 VDC Input 22.8 24.0 25.2 • 1W Output Power • Tightly Regulated • Single & Dual Outputs Input Voltage Range Input Filter VDC Internal Capacitor • Miniature SIP Case Reverse Polarity Input Current • 1,000 VDC Isolation Output • >3.5 MHour MTBF Parameter • 18 Standard Models Output Voltage Accuracy • Industry Standard Pin-Out Output Voltage Balance • LOWEST COST!! Units Conditions Min. Load Regulation (Note 1) A Max. Units ±3.0 % ±1.0 % For Vin Min to Max ±0.25 % For Iout = 10% to 100% ±1.0 % 20 mV P - P ±0.03 %/ºC Max. Units Dual Output , Balanced Loads Line Regulation Typ. 0.3 ±0.1 Ripple & Noise (20 MHz) (Note 3) 10 Output Power Protection 120 % Temperature Coefficient Output Short Circuit Momentary (1.0 Sec.) General Parameter Conditions Isolation Voltage Isolation Resistance Isolation Capacitance Min. 60 Seconds 1,000 500 VDC 1,000 100 kHz, 1V Switching Frequency Typ. VDC M 60 pF 100 kHz Environmental Parameter Min. Typ. Max. Operating Temperature Range Conditions Ambient -40 +25 +85 ºC Operating Temperature Range Case -40 +90 ºC -55 +125 ºC 95 % Storage Temperature Range Cooling Units Free Air Convection Humidity RH, Non-condensing Physical Case Size (Single Output) 0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm) Case Size (Dual Output) 1.08 x 0.37 x 0.47 Inches (27.5 x 9.5 x 12.0 mm) MicroPower Direct Case Material 292 Page Street Suite D Stoughton, MA 02072 USA Weight Non-Conductive Black Plastic (UL94-V0) T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Absolute Maximum Ratings 0.07 Oz (2.1g) Reliability Specifications Parameter Conditions MTBF Min. MIL HDBK 217F, 25ºC, Gnd Benign Parameter Conditions Min. 5 VDC Input Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Typ. Max. 3.5 Units MHours Typ. Max. -0.7 9.0 12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 Units VDC 1.5 mm From Case For 10 Sec 300 ºC All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com www.micropowerdirect.com Model Selection Guide Input Model Number Voltage (VDC) Output Current (mA) Efficiency Voltage Current Current (VDC) (mA, Max) (mA, Min) (%, Typ) Fuse Rating Slow-Blow (mA) Nominal Range Full-Load No-Load D101ER 5 4.75 - 5.25 294 30 5.0 200.0 20.0 68 500 D102ER 5 4.75 - 5.25 286 30 9.0 111.0 12.0 70 500 D103ER 5 4.75 - 5.25 282 30 12.0 83.0 9.0 71 500 D104ER 5 4.75 - 5.25 278 30 15.0 67.0 7.0 72 500 D105ER 5 4.75 - 5.25 290 30 ±5.0 ±100.0 ±10.0 69 500 D107ER 5 4.75 - 5.25 278 30 ±12.0 ±42.0 ±5.0 72 500 D108ER 5 4.75 - 5.25 278 30 ±15.0 ±33.0 ±4.0 72 500 D111ER 12 11.4 - 12.6 121 15 5.0 150.0 15.0 69 200 D112ER 12 11.4 - 12.6 117 15 9.0 111.0 12.0 71 200 D113ER 12 11.4 - 12.6 116 15 12.0 83.0 9.0 72 200 D114ER 12 11.4 - 12.6 116 15 15.0 67.0 7.0 72 200 D115ER 12 11.4 - 12.6 119 15 ±5.0 ±100.0 ±10.0 70 200 D117ER 12 11.4 - 12.6 114 15 ±12.0 ±42.0 ±5.0 73 200 D121ER 24 22.8 - 25.2 59 8 5.0 150.0 15.0 70 100 D122ER 24 22.8 - 25.2 58 8 9.0 111.0 12.0 72 100 D123ER 24 22.8 - 25.2 57 8 12.0 83.0 9.0 73 100 D124ER 24 22.8 - 25.2 57 8 15.0 67.0 7.0 73 100 D125ER 24 22.8 - 25.2 58 8 ±5.0 ±100.0 ±10.0 72 100 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhace stability over temperature and input line variations. Recommended capacitor Output Capacitor Input values are given in the table Vin Vout Capacitor at right. For applications Single Dual requiring very low output 5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF noise levels, a simple LC 12 VDC 2.2 µF 9 VDC 4.7 µF 2.2 µF filter should be effective. 4. It is recommended that a 24 VDC 1.0 µF 12 VDC 2.2 µF 1.0 µF fuse be used on the input of 15 VDC 1.0 µF 0.47 µF a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve Mechanical Dimensions (Single Output) Mechanical Dimensions (Dual Output) Pin Connections Pin Single 1 2 4 6 7 9 10 +Vin +Vin -Vin -Vin -Vout No Pin +Vout No Pin No Pin +Vout No Pin -Vout No Pin Common Dual MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit FAX: (781) 344-8481 • E-Mail: [email protected]