HSP-300 300W Single Output with PFC Function series ■ Features : •Universal AC input / Full range •Withstand 300VAC surge input for 5 seconds •Built-in active PFC function •Low leakage current<1mA •Protections: Short circuit / Overload / Over voltage / Over temperature •Cooling by free air convection •Low profile:31mm •Conformal coated •LED indicator for power on •Suitable for high efficiency moving sign applications •3 years warranty SPECIFICATION HSP-300-2.8 HSP-300-4.2 HSP-300-5 DC VOLTAGE 2.8V 4.2V 5V RATED CURRENT CURRENT RANGE Note.5 60A 0 ~ 60A 60A 0 ~ 60A 60A 0 ~ 60A 252W 150mVp-p 3.6~4.4V 300W 150mVp-p 4.5~5.5V ±2.0% ±2.0% ±0.5% ±0.5% MODEL OUTPUT RATED POWER(convection) 168W RIPPLE & NOISE (max.) Note.2 110mVp-p VOLTAGE ADJ. RANGE 2.5~3V VOLTAGE TOLERANCE Note.3 ±2.0% LINE REGULATION ±0.5% LOAD REGULATION ±1.0% 2000ms, 100ms/230VAC SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE 8ms/230VAC Note.4 180 ~ 264VAC FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT 47 ~ 63Hz PF≥0.93/230VAC ±1.0% 3000ms, 100ms/115VAC at full load 8ms/115VAC at full load 254 ~ 370VDC or 90~135VAC ±1.0% 127~190VDC PF ≥0.98/115VAC at full load 87% 85% 80% 2.8A/115VAC 1.4A/230VAC Cold start 30A/115VAC 60A/230VAC 3.9A/115VAC 1.95A/230VAC 4.7A/115VAC 2.35A/230VAC <1mA / 240VAC 105~150% rated output power OVERLOAD PROTECTION SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. Protection type : Hiccup mode, recovers automatically after fault condition is removed Protection type : Hiccup mode, recovers automatically after fault condition is removed 4.6 ~ 5.4V 3.22 ~ 3.78V 5.7 ~ 7.0V Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after fault condition is removed -30 ~ +70℃(Refer to "Derating Curve") 20 ~ 90% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH ±0.03%/℃ (0 ~ 60℃) TEMP. COEFFICIENT 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes VIBRATION SAFETY & EMC (Note 5) SAFETY STANDARDS WITHSTAND VOLTAGE UL60950-1,EN60950-1,CCC GB4943 approved ISOLATION RESISTANCE EMC EMISSION I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC/25℃/ 70%RH Compliance to EN55022 (CISPR22),GB9254,Class B, EN61000-3-2,-3,GB17625.1 Compliance to EN61000-4-2,3,4,5,6,8,11;EN55024, light industry level (surge 4KV), criteria A EMC IMMUNITY OTHERS NOTE I/P-O/P:3.0KVAC I/P-FG:2.0KVAC O/P-FG:0.5KVAC MIL-HDBK-217F (25℃) MTBF 263.2K hrs min. DIMENSION PACKING 210*81*31mm (L*W*H) 0.8kg; 15pcs/ 12.1kg/ 0.7CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltages. Please check the static characteristics for more details. 5. Please refer to Static Characteristics". 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:HSP-300-SPEC 2015-03-30 HSP-300 300W Single Output with PFC Function Mechanical Specification CASE NO.: 233B series Unit:mm 210 204 3 9 ADJ 1 63 81 TB1 3 2 2 3 1 4 31 4*ψ4.2 AC Input Terminal(TB1) pin NO. Assignment Pin No. 1 2 3 Assignment AC/L AC/N DC Output Terminal pin NO. Assignment Terminal Pin No. 1,2 3,4 DG28C-B-03P-13-00AH Assignment +V -V Terminal NEL-400-02P Block Diagram EMI FILTER I/P BRIDGE RECTIFIERS APFC CONTROLLER POWER SWITCHING SYNCHRONOUS RECTIFIERS & FILTER +V -V O.T.P. FG O.L.P. DETECTION CIRCUIT PWM CONVERTER O.V.P. Derating Curve Static Characteristics 180~264VAC 60 60 90~135VAC 50 50 30 Io(A) Io(A) 40 40 35 30 25 20 10 10 -30 20 0 10 20 30 40 45 50 AMBIENT TEMPERATURE (℃) 60 70 (HORIZONTAL) 90 100 120 135 160 170 180 220 240 264 INPUT VOLTAGE (V) 60Hz File Name:HSP-300-SPEC 2015-03-30 HSP-300 300W Single Output Switching Power Supply series Installation 1.Operate with additional aluminum plate In order to meet the“Derating Curve”and the “Static Characteristics” ,HSP-300 series must be installed onto an aluminum plate(or the cabinet of the same size) on the bottom.The size of the suggested aluminum plate is shown as below. And for optimizing thermal performance, the aluminum plate must have an even and smooth surface (or coated with thermal grease), and HSP-300 series must be firmly mounted at the center of the aluminum plate. Unit:mm M3*4 3 450 450 5cm 5cm 5cm 2.For heat dissipation, at least 5cm installation distance around the PSU should be kept, shown as below: 5cm 5cm File Name:HSP-300-SPEC 2015-03-30