PLD-60 60W Single Output LED Power Supply series ■ Features : Built-in active PFC function Constant current design Protections: Short circuit / Over temperature Cooling by free air convection Fully isolated plastic case IP42 design Class Ⅱ power unit, no FG Suitable for indoor LED lighting applications 100% full load burn-in test Low cost High reliability 3 years warranty M M F 110 SPECIFICATION MODEL RATED CURRENT PLD-60-700B PLD-60-1050B PLD-60-1400B PLD-60-1750B PLD-60-2000B PLD-60-2400B 500mA 700mA 1050mA 1400mA 1750mA 2000mA 2400mA 50 ~ 86V 34 ~ 57V 25 ~ 43V 20 ~ 34V 18 ~ 30V 15 ~ 25V 60W CURRENT ACCURACY ±5.0% RATED POWER 54W 60.2W 59.85W 60.2W 59.5W 60W RIPPLE & NOISE (max.) Note.1 10.2Vp-p 5.6Vp-p 3.8Vp-p 3.4Vp-p 3.3Vp-p 2.4Vp-p 2.4Vp-p NO LOAD OUTPUT VOLTAGE (max.) 118V 100V 63V 50V 50V 35V 35V SETUP TIME INPUT 180~295VAC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.9/230VAC, PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve) TOTAL HARMONIC DISTORTION THD< 20% when output loading≧60%(PLD-60-500B loading≧65%)at 230VAC input and output loading≧75% at 277VAC input 88% 87% 87% 86% 86% 86% 85% EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT(Typ.) 0.6A/230VAC 0.5A/277VAC COLD START 25A (twidth=60μs measured at 50% Ipeak) at 230VAC MAX. No. of PSUs on 16A CIRCUIT BREAKER 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT EMC -30 ~ +45℃ (Refer to "Derating Curve") 20 ~ 95% RH non-condensing -40 ~ +80℃, 10 ~ 95% RH ±0.03%/℃ (0 ~ 50℃) 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS ENEC EN61347-1, EN61347-2-13 independent, EN62384, IP42 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25℃/ 70% RH Compliance to EN55015, EN61000-3-2 Class C ; EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level(Surge 2KV), criteria B EMC EMISSION DIMENSION PACKING NOTE <0.5mA / 240VAC Hiccup mode, recovers automatically after fault condition is removed. Shut down o/p voltage, auto-recovery VIBRATION EMC IMMUNITY MTBF OTHERS 500ms / 230VAC at full load VOLTAGE RANGE SHORT CIRCUIT PROTECTION OVER TEMPERATURE SAFETY & IP42 PLD-60-500B OPERATING VOLTAGE RANGE 70 ~ 108V OUTPUT SELV 458.852Khrs min. MIL-HDBK-217F (25℃) 128*60*31.5mm (L*W*H) 0.34Kg;30pcs/11.2Kg/0.58CUFT 1. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 2. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. 3. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. File Name:PLD-60-SPEC 2015-08-21 PLD-60 60W Single Output LED Power Supply Mechanical Specification Case No. 3 series Unit:mm 128 150±10 15.3 UL1430 18AWG 60 7.3 75±5 7.3 T case H03VVH2-F 0.75mm2 X2C AC/L(BROWN) 3.6 2 -ψ -ψ8 .9 2 15.3 10 20 AC/N(BLUE) V+(RED) V-(BLACK) 3 1.9 31.5 ※ T case: Max. Case Temperature. Block Diagram fosc :60KHz(230VAC) EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING +V -V DETECTION CIRCUIT O.L.P. PWM & PFC CONTROL Derating Curve O.C.P. Static Characteristics 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 50 40 20 -30 60 50 40 -25 -5 0 15 30 40 45 50 AMBIENT TEMPERATURE (℃) 60 (HORIZONTAL) 295 180 INPUT VOLTAGE (V) File Name:PLD-60-SPEC 2015-08-21 PLD-60 60W Single Output LED Power Supply series Power Factor Characteristic Constant Current Mode 0.96 0.94 PF 0.92 0.9 230V 0.88 277V 0.86 0.84 0.82 50% 60% 70% 80% 90% 100% (60W) LOAD EFFICIENCY vs LOAD (PLD-60-500B) PLD-60 series possess superior working efficiency that up to 88% can be reached in field applications. 100 90 EFFICIENCY (%) 80 70 60 230V 50 40 277V 30 20 10 0 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD File Name:PLD-60-SPEC 2015-08-21