SOD1H1-SOD1H8 Surface Mount Rectifiers REVERSE VOLTAGE: 50 - 1000 V CURRENT: 1.0 A SOD - 123FL Features 1.9± 0.1 ◇ ◇ ◇ 0.10-0.30 2.8±0.1 0.6±0.25 Mechanical Data ◇ 1.0±0.2 Cathode Band Top View Glass passivated device Ideal for surface mounted applications Low leakage current Metallurgically bonded construction High temperature soldering: 250℃/10 seconds at terminals 1.4± 0.15 ◇ ◇ ◇ ◇ ◇ Case:JEDEC SOD-123FL,molded plastic over passivated chip 3.7±0.2 Polarity: Color band denotes cathode end Weight: 0.0008 ounces, 0.022 gram Mounting position: Any Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified. Single phase,half wave,60Hz,resistive or inductive load.For capactive load,derate current by 20%. ABSOLUTE RATINGS Device marking code SOD 1H1 H1 SOD 1H2 H2 SOD SOD SOD SOD SOD SOD 1H3 1H4 1H5 1H6 1H7 1H8 UNITS H3 H4 H5 H6 H7 H8 Maximum recurrent peak reverse voltage VRRM 50 100 200 300 400 600 800 1000 V Maximum RMS voltage VRMS 35 70 140 210 280 420 560 700 V Maximum DC blocking voltage VDC 50 100 200 300 400 600 800 1000 V Maximum average forward rectified current T A=65℃ I(AV) 1.0 A IFSM 25 A Peak forward surge current 8.3ms single half-sine-wave superimposed on rated load T L=25℃ Maximum instantaneous (NOTE 1) VF forward voltage at 1.0A Maximum DC reverse current @TA=25℃ 1.0 1.3 10 IR at rated DC blocking voltage @T A=125℃ 1.7 V µA 200 Maximum reverse recovery time (NOTE 2) trr Operating temperature range Tj - 55 --- + 150 ℃ TSTG - 55 --- + 150 ℃ Storage temperature range NOTES:1.Pulse test:300ms pulse width,1% duty cycle. 2.Measured with IF=0.5A, IR=1A, Irr=0.25A. 50 75 ns SOD1H1-SOD1H8 Surface Mount Rectifiers Ratings AND Charactieristic Curves .8 .6 .4 Single Phase Half Wave 60Hz Resistive or Inductive Load .2 0 0 25 50 75 100 125 150 175 FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) 1.0 25 20 15 10 5 8.3ms Single Half Sine-Wave (JEDED Method) 0 1 2 4 6 8 10 20 40 60 80 100 NUMBER OF CYCLES AT 60Hz FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 1 SO SO D1 H4 D1 -SO H6 -SO D1 H5 D1 H8 100 0.1 o 0.01 .4 Tj=25 C Pulse Width=300 s 1% Duty Cycle .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) INSTANTANEOUS REVERSE CURRENT, (uA) AMBIENT TEMPERATURE, ( ) SO D1 H1 -SO D1 H3 INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 100 TJ = 100 10 4 1 .4 TJ = 25 .1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%)