ER07A-ER07J Surface Mount Rectifiers REVERSE VOLTAGE: 50 - 600 V CURRENT: 1.0 A SOD - 123FL Features 1.0±0.2 1.9± 0.1 Glass passivated device Ideal for surface mounted applications Low leakage current Metallurgically bonded construction High temperature soldering: 250℃/10 seconds at terminals 0.10-0.30 2.8±0.1 1.4± 0.15 ◇ ◇ ◇ ◇ ◇ Cathode Band Top View 0.6±0.25 Mechanical Data ◇ ◇ ◇ ◇ Case:JEDEC SOD-123FL,molded plastic over passivated chip Polarity: Color band denotes cathode end Weight: 0.003 ounces, 0.01 gram Mounting position: Any 3.7±0.2 Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified. Single phase,half wave,60Hz,resistive or inductive load.For capactive load,derate current by 20%. ABSOLUTE RATINGS Device marking ER 07A ER 07B ER 07C ER 07D ER 07E ER 07G ER 07H E1 E2 E3 E4 E5 E6 E7 E8 ER UNITS 07J Maximum recurrent peak reverse voltage VRRM 50 100 150 200 300 400 500 600 V Maximum RMS voltage VRMS 35 70 105 140 210 280 350 420 V Maximum DC blocking voltage VDC 50 100 150 200 300 400 500 600 V Maximum average forward rectified current T A=65℃ I(AV) 1.0 A IFSM 20 A Peak forward surge current 8.3ms single half-sine-wave superimposed on rated load T L=25℃ Maximum instantaneous (NOTE 1) VF forward voltage at 1.0A Maximum DC reverse current @TA=25℃ IR at rated DC blocking voltage @T A=125℃ 0.95 1.25 5.0 150 1.7 V µA Maximum reverse recovery time (NOTE 2) trr 35 ns Operating temperature range Tj - 55 --- + 150 ℃ TSTG - 55 --- + 150 ℃ Storage temperature range NOTES:1.Pulse test:300ms pulse width,1% duty cycle. 2.Measured with IF=0.5A, IR=1A, Irr=0.25A. ER07A-ER07J Surface Mount Rectifiers Ratings AND Charactieristic Curves .8 .7 .6 .4 Single Phase Half Wave 60Hz Resistive or Inductive Load .2 0 0 25 50 75 100 125 150 175 FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) 1.0 20 10 8.3ms Single Half Sine-Wave (JEDED Method) 0 1 2 4 6 8 10 20 40 60 80 100 NUMBER OF CYCLES AT 60Hz FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 10 ER 07 ER E-E 07 HR0 ER 7G 07 J 1 0.1 o 0.01 Tj=25 C Pulse Width=300 s 1% Duty Cycle 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 INSTANTANEOUS FORWARD VOLTAGE, (V) INSTANTANEOUS REVERSE CURRENT, (uA) AMBIENT TEMPERATURE, ( ) ER 07A -ER 07D INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 100 TJ = 100 10 4 1 .4 TJ = 25 .1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%)