SMAJ SERIES

SMAJ SERIES
400Watts Surface Mount Transient Voltage Suppressor
SMA/DO-214AC
Features
For surface mounted application
Low profile package
Built-in strain relief
Glass passivated junction
Excellent clamping capability
Fast response time: Typically less than 1.0ps
from 0 volt to BV min.
Typical IR less than 1µA above 10V
High temperature soldering guaranteed:
260oC / 10 seconds at terminals
Plastic material used carries Underwriters
Laboratory Flammability Classification 94V-0
400 watts peak pulse power capability with a 10
x 1000 us waveform by 0.01% duty cycle
(300W above 78V).
Dimensions in inches and (millimeters)
Mechanical Data
Case: Molded plastic
Terminals: Pure tin plated lead free,
Polarity: Indicated by cathode band
Standard packaging: 12mm tape
Weight: 0.064 gram
Maximum Ratings and Electrical Characteristics
Rating at 25 OC ambient temperature unless otherwise specified.
Type Number
o
Peak Power Dissipation at TA=25 C, Tp=1ms(Note 1)
Steady State Power Dissipation
Peak Forward Surge Current, 8.3 ms Single Half
Sine-wave Superimposed on Rated Load
(JEDEC method) (Note 2, 3)
Maximum Instantaneous Forward Voltage at 25.0A for
Unidirectional Only
Symbol
PPK
Pd
Value
Minimum 400
1
Units
Watts
Watts
IFSM
40.0
Amps
VF
3.5
Volts
Operating and Storage Temperature Range
TJ, TSTG
-55 to + 150
1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25oC Per Fig. 2.
Notes:
2. Mounted on 5.0mm2 (.013 mm Thick) Copper Pads to Each Terminal.
3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per
Minute Maximum.
Devices for Bipolar Applications
1. For Bidrectional Use C or CA Suffix for Types SMAJ5.0 through Types SMAJ188.
2. Electrical Characteristics Apply in Both Directions.
o
C
SMAJ SERIES
400Watts Surface Mount Transient Voltage Suppressor
RATINGS AND CHARACTERISTIC CURVES (SMAJ SERIES)
FIG.1- PEAK PULSE POWER RATING CURVE
FIG.2- PULSE DERATING CURVE
Pppm, PEAK PULSE POWER, KW
NON-REPETITIVE
PULSE WAVEFORM
SHOWN in FIG. 3
TA=250C
10
1
0.2" sq 5.0mm2 COPPER PAD AREAS
0.1
10 s
0.1 s
1.0 s
100 s
1.0ms
10ms
PEAK PULSE POWER (Pppm) or CURRENT (lpp)
DERATING IN PERCENTAGE, %
100
100
75
50
25
0
0
75
100
125
150
175
200
FIG.4- MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
150
50
PEAK FORWARD SURGE CURRENT. (A)
lppm, PEAK PULSE CURRENT %
50
TA, AMBIENT TEMPERATURE. C
FIG.3- CLAMPING POWER PULSE WAVEFORM
PULSE WIDTH (td) is DEFINED
tr=10 sec. AS THE POINT WHERE THE PEAK
CURRENT DECAYS to 50% of lppm
PEAK VALUE
lppm
100
HALF VALUE- lpp
2
10/1000 sec. WAVEFORM
AS DEFINED BY R.E.A.
50
td
0
0
2.0
3.0
FIG.5- TYPICAL JUNCTION CAPACITANCE
Tj=25 0C
f=1.0MHz
Vsig=50mVp-p
1000
MEASURED AT
ZERO BIAS
100
MEASURED AT
STAND-OFF
VOLTAGE,VWM
1
30
20
10
4.0
1
10
NUMBER OF CYCLES AT 60Hz
10000
10
8.3ms Single Half Sine Wave
JEDEC Method
TJ=TJ max.
40
0
1.0
t, TIME, ms
Cj, JUNCTION CAPACITANCE, pF
25
O
td. PULSE WIDTH, sec.
10
V(BR), BREAKDOWN VOLTAGE. (V)
100
200
100
SMAJ SERIES
400Watts Surface Mount Transient Voltage Suppressor
ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted)
Device
SMAJ5.0
SMAJ5.0A
SMAJ6.0
SMAJ6.0A
SMAJ6.5
SMAJ6.5A
SMAJ7.0
SMAJ7.0A
SMAJ7.5
SMAJ7.5A
SMAJ8.0
SMAJ8.0A
SMAJ8.5
SMAJ8.5A
SMAJ9.0
SMAJ9.0A
SMAJ10
SMAJ10A
SMAJ11
SMAJ11A
SMAJ12
SMAJ12A
SMAJ13
SMAJ13A
SMAJ14
SMAJ14A
SMAJ15
SMAJ15A
SMAJ16
SMAJ16A
SMAJ17
SMAJ17A
SMAJ18
SMAJ18A
SMAJ20
SMAJ20A
SMAJ22
SMAJ22A
SMAJ24
SMAJ24A
SMAJ26
SMAJ26A
SMAJ28
SMAJ28A
SMAJ30
SMAJ30A
SMAJ33
SMAJ33A
SMAJ36
SMAJ36A
SMAJ40
SMAJ40A
SMAJ43
SMAJ43A
Device
Marking
Code
AD
AE
AF
AG
AH
AK
AL
AM
AN
AP
AQ
AR
AS
AT
AU
AV
AW
AX
AY
AZ
BD
BE
BF
BG
BH
BK
BL
BM
BN
BP
BQ
BR
BS
BT
BU
BV
BW
BX
BY
BZ
CD
CE
CF
CG
CH
CK
CL
CM
CN
CP
CQ
CR
CS
CT
Working Peak
Reverse
Voltage
VWM(Volts)
5.0
5.0
6.0
6.0
6.5
6.5
7.0
7.0
7.5
7.5
8.0
8.0
8.5
8.5
9.0
9.0
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
20
20
22
22
24
24
26
26
28
28
30
30
33
33
36
36
40
40
43
43
Breakdown Voltage
V(BR) (Volts)
at IT
Min.
Max.
6.40
7.30
6.40
7.00
6.67
8.15
6.67
7.37
7.22
8.82
7.22
7.98
7.78
9.51
7.78
8.60
8.33
10.3
8.33
9.21
8.89
10.9
8.89
9.83
9.44
11.5
9.44
10.4
10.0
12.2
10.0
11.1
11.1
13.6
11.1
12.3
12.2
14.9
12.2
13.5
13.3
16.3
13.3
14.7
14.4
17.6
14.4
15.9
15.6
19.1
15.6
17.2
16.7
20.4
16.7
18.5
17.8
21.8
17.8
19.7
18.9
23.1
18.9
20.9
20.0
24.4
20.0
22.1
22.2
27.1
22.2
24.5
24.4
29.8
24.4
26.9
26.7
32.6
26.7
29.5
28.9
35.3
28.9
31.9
31.1
38.0
31.1
34.4
33.3
40.7
33.3
36.8
36.7
44.9
36.7
40.6
40.0
48.9
40.0
44.2
44.4
54.3
44.4
49.1
47.8
58.4
47.8
52.8
Test
Current
IT
(mA)
10
10
10
10
10
10
10
10
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
Maximum
Clamping
Voltage at IPPM
VC(Volts)
(Note 5)
9.6
9.2
11.4
10.3
12.3
11.2
13.3
12.0
14.3
12.9
15.0
13.6
15.9
14.4
16.9
15.4
18.8
17.0
20.1
18.2
22.0
19.9
23.8
21.5
25.8
23.2
26.9
24.4
28.8
26.0
30.5
27.6
32.2
29.2
35.8
32.4
39.4
35.5
43.0
38.9
46.6
42.1
50.0
45.4
53.5
48.4
59.0
53.3
64.3
58.1
71.4
64.5
76.7
69.4
Maximum
Peak Pulse
Surge Current
IPPM
(Note 5)(Amps)
41.7
43.5
35.1
38.8
32.5
35.7
30.1
33.3
28.0
31.0
26.7
29.4
25.2
27.8
23.7
26.0
21.3
23.5
19.9
22.0
18.2
20.1
16.8
18.6
15.5
17.2
14.9
16.4
13.9
15.4
13.1
14.5
12.4
13.7
11.2
12.3
10.2
11.3
9.3
10.3
8.6
9.5
8.0
8.8
7.5
8.3
6.8
7.5
6.2
6.9
5.6
6.2
5.2
5.8
Maximum
Reverse
Leakage
at VWM
ID (uA)
800
800
800
800
500
500
200
200
100
100
50.0
50.0
10.0
10.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
SMAJ SERIES
400Watts Surface Mount Transient Voltage Suppressor
ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted)
Device
Device
Marking
Code
Working Peak
Reverse
Voltage
VWM(Volts)
45
45
48
48
51
51
54
54
58
58
60
60
64
64
70
70
75
75
78
78
85
85
90
90
100
100
110
110
120
120
130
130
150
150
160
160
170
170
188
188
Breakdown Voltage
V(BR) (Volts)
at IT
Min.
Max.
50.0
61.1
50.0
55.3
53.3
65.1
53.3
58.9
56.7
69.3
56.7
62.7
60.0
73.3
60.0
66.3
64.4
78.7
64.4
71.2
66.7
81.5
66.7
73.7
71.1
86.9
71.1
78.6
77.8
95.1
77.8
86.0
83.3
102
83.3
92.1
86.7
106
86.7
95.8
94.4
115
94.4
104
100
122
100
111
111
136
111
123
122
149
122
135
133
163
133
147
144
176
144
159
167
204
167
185
178
218
178
197
189
231
189
209
209
255
209
231
Test
Current
IT
(mA)
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
CU
SMAJ45
CV
SMAJ45A
CW
SMAJ48
CX
SMAJ48A
CY
SMAJ51
CZ
SMAJ51A
RD
SMAJ54
RE
SMAJ54A
RF
SMAJ58
RG
SMAJ58A
RH
SMAJ60
RK
SMAJ60A
RL
SMAJ64
RM
SMAJ64A
RN
SMAJ70
RP
SMAJ70A
RQ
SMAJ75
RR
SMAJ75A
RS
SMAJ78
RT
SMAJ78A
RU
SMAJ85
RV
SMAJ85A
RW
SMAJ90
RX
SMAJ90A
RY
SMAJ100
RZ
SMAJ100A
SD
SMAJ110
SE
SMAJ110A
SF
SMAJ120
SG
SMAJ120A
SH
SMAJ130
SK
SMAJ130A
SL
SMAJ150
SM
SMAJ150A
SN
SMAJ160
SP
SMAJ160A
SQ
SMAJ170
SR
SMAJ170A
ST
SMAJ188
SS
SMAJ188A
Notes:
O
1. Non-repetitive current pulse, per Fig. 3 and derated above TA=25 C per Fig. 2
2
2. Mounted on 5.0mm copper pads to each terminal
O
3. Lead temperature at TL=75 C
4. Measured on 8.3ms single half sine-wave duty cycle=4 pulses per minutes maximum
5. Peak pulse power waveform is 10/1000 us
6. For Bi-Directional devices having VR of 10 volts and under, the IR limit is double.
Maximum
Clamping
Voltage at IPPM
VC(Volts)
(Note 5)
80.3
72.7
85.5
77.4
91.1
82.4
96.3
87.1
103
93.6
107
96.8
114
103
125
113
134
121
139
126
151
137
160
146
179
162
196
177
214
193
231
209
266
243
287
259
304
275
344
328
Maximum
Peak Pulse
Surge Current
IPPM
(Note 5)(Amps)
5.0
5.5
4.7
5.2
4.4
4.9
4.2
4.6
3.9
4.3
3.7
4.1
3.5
3.9
3.2
3.5
3.0
3.3
2.9
3.2
2.0
2.2
1.9
2.1
1.7
1.9
1.6
1.7
1.4
1.6
1.3
1.5
1.1
1.3
1.0
1.2
1.0
1.1
0.9
0.91
Maximum
Reverse
Leakage
at VWM
ID (uA)
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
5.0
SMAJ SERIES
400Watts Surface Mount Transient Voltage Suppressor
This device is designed specifically for
APPLICATION NOTES:
Recommended Pad Layout
transiient voltage suppression from threats
generated by ESD for board levelload
switching components.
The pad dimensions should be 0.010" longer than the
contact size in the lead axis. This allows a solder fillet
to form, see figure below. Contact factory for soldering
methods.
The wide leads assure a large surface contact
for good heat disipation, and a low resistance
path for surge current flow to ground.
This series is designed to optimize board
space and for use with surface mount technology
automated assembly equipment.
They can be easily mounted on printed circuit
boards and ceramic substrates to protect
sensitive components from transient voltage
damage.
Dimensions in inches and (millimeters)