1.5SMC SERIES 1500 Watts Surface Mount Transient Voltage Suppressor SMC/DO-214AB Features For surface mounted application in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Excellent clamping capability Fast response time: Typically less than 1.0ps from 0 volt to BV min. Typical IR less than 1μA above 10V High temperature soldering guaranteed: 260oC / 10 seconds at terminals Plastic material used carries Underwriters Laboratory Flammability Classification 94V-0 1500 watts peak pulse power capability with a 10 x 1000 us waveform by 0.01% duty cycle Dimensions in inches and (millimeters) Mechanical Data Case: Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Weight: 0.21gram Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Type Number Symbol PPK PM(AV) Value Minimum 1500 6.5 Units Watts W Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 2, 3) - Unidirectional Only IFSM 200 Amps Thermal Resistance Junction to Ambient Air (Note 4) RθJA Thermal Resistance Junction to Leads RθJL 50 15 -55 to + 150 o Peak Power Dissipation at TA=25 C, Tp=1ms ( Note 1) o Power Dissipation on Intinite Heatsink, TA=50 C o o C/W C/W o C Operating and Storage Temperature Range TJ, TSTG o 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25 C Per Fig. 2. Notes: 2 2. Mounted on 8.0mm (.013mm Thick) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minute Maximum. 4. Mounted on 5.0mm2(.013mm thick) land areas. Devices for Bipolar Applications 1. For Bidrectional Use C or CA Suffix for Types 1.5SMC6.8 through Types 1.5SMC200A. 2. Electrical Characteristics Apply in Both Directions. http://www.luguang.cn - 542 - mail:[email protected] 1.5SMC SERIES 1500 Watts Surface Mount Transient Voltage Suppressor RATINGS AND CHARACTERISTIC CURVES (1.5SMC SERIES) FIG.2- PULSE DERATING CURVE FIG.1- PEAK PULSE POWER RATING CURVE 10 1 0.1 0.1 s 1 s 10 s 100 s 1.0ms 10ms DERATING IN PERCENTAGE. % 200 NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG.3 O TA = 25 C PEAK PULSE POWER (PPP) or CURRENT (IPPM) PPPM, PEAK PULSE POWER, KW 100 150 100 50 0 0 tp, PULSE WIDTH, sec. 50 75 100 125 150 175 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY 150 Peak Value IPPM 100 PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS to 50% of IPPM Half Value - IPPM 2 10/1000 sec. WAVEFORM as DEFINED by R.E.A. 50 td 0 IFSM, PEAK FORWARD SURGE CURRENT, AMPERES 200 tr = 10 sec 8.3ms Single Half Sine Wave JEDEC Method Tj=Tj max. 100 10 0 1.0 2.0 3.0 4.0 t, TIME, ms 1 10 100 NUMBER OF CYCLES AT 60Hz FIG.5- TYPICAL JUNCTION CAPACITANCE UNIDIRECTIONAL 10000 UNIDIRECTIONAL BIDIRECTIONA CJ, JUNCTION CAPACITANCE. (pF) 200 O TA, AMBIENT TEMPERATURE. ( C) FIG.3- CLAMPING POWER PULSE WAVEFORM PEAK PULSE CURRENT - % 25 VR=0 1000 O Tj = 25 C f=1.0MHz Vsig=50mVp-p 100 VR-RATED STAND-OFF VOLTAGE 10 1 10 100 200 V(BR), BREAKDOWN VOLTAGE. VOLTS http://www.luguang.cn mail:[email protected] Version: B07 1.5SMC SERIES 1500 Watts Surface Mount Transient Voltage Suppressor ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) GENERAL PART NUMBER 1.5SMC6.8 1.5SMC6.8A 1.5SMC7.5 1.5SMC7.5A 1.5SMC8.2 1.5SMC8.2A 1.5SMC9.1 1.5SMC9.1A 1.5SMC10 1.5SMC10A 1.5SMC11 1.5SMC11A 1.5SMC12 1.5SMC12A 1.5SMC13 1.5SMC13A 1.5SMC15 1.5SMC15A 1.5SMC16 1.5SMC16A 1.5SMC18 1.5SMC18A 1.5SMC20 1.5SMC20A 1.5SMC22 1.5SMC22A 1.5SMC24 1.5SMC24A 1.5SMC27 1.5SMC27A 1.5SMC30 1.5SMC30A 1.5SMC33 1.5SMC33A 1.5SMC36 1.5SMC36A 1.5SMC39 1.5SMC39A 1.5SMC43 1.5SMC43A 1.5SMC47 1.5SMC47A 1.5SMC51 1.5SMC51A 1.5SMC56 1.5SMC56A 1.5SMC62 1.5SMC62A 1.5SMC68 1.5SMC68A 1.5SMC75 1.5SMC75A 1.5SMC82 1.5SMC82A 1.5SMC91 1.5SMC91A Device Marking Code 1.5SMC6.8 1.5SMC6.8A 1.5SMC7.5 1.5SMC7.5A 1.5SMC8.2 1.5SMC8.2A 1.5SMC9.1 1.5SMC9.1A 1.5SMC10 1.5SMC10A 1.5SMC11 1.5SMC11A 1.5SMC12 1.5SMC12A 1.5SMC13 1.5SMC13A 1.5SMC15 1.5SMC15A 1.5SMC16 1.5SMC16A 1.5SMC18 1.5SMC18A 1.5SMC20 1.5SMC20A 1.5SMC22 1.5SMC22A 1.5SMC24 1.5SMC24A 1.5SMC27 1.5SMC27A 1.5SMC30 1.5SMC30A 1.5SMC33 1.5SMC33A 1.5SMC36 1.5SMC36A 1.5SMC39 1.5SMC39A 1.5SMC43 1.5SMC43A 1.5SMC47 1.5SMC47A 1.5SMC51 1.5SMC51A 1.5SMC56 1.5SMC56A 1.5SMC62 1.5SMC62A 1.5SMC68 1.5SMC68A 1.5SMC75 1.5SMC75A 1.5SMC82 1.5SMC82A 1.5SMC91 1.5SMC91A Stand-Off Maximum Maximum Maximum Maximum Breakdown Voltage Test Current Voltage Reverse Leakage Peak Surge Clamping Temperature VBR @IT(mA) VWM at Vwm Current IPPM Voltage at IPPM Coefficient (Volts) (Note 1) O Min Max (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C) 6.12 6.45 6.75 7.13 7.38 7.79 8.19 8.65 9.00 9.50 9.90 10.5 10.8 11.4 11.7 12.4 13.5 14.3 14.4 15.2 16.2 17.1 18.0 19.0 19.8 20.9 21.6 22.8 24.3 25.7 27.0 28.5 29.7 31.4 32.4 34.2 35.1 37.1 38.7 40.9 42.3 44.7 45.9 48.5 50.4 53.2 55.8 58.9 61.2 64.6 67.5 71.3 73.8 77.9 81.9 86.5 7.48 7.14 8.25 7.88 9.02 8.61 10.0 9.55 11.0 10.5 12.1 11.6 13.2 12.6 14.3 13.7 16.5 15.8 17.6 16.8 19.8 18.9 22.0 21.0 24.2 23.1 26.4 25.2 29.7 28.4 33.0 31.5 36.3 34.7 39.6 37.8 42.9 41.0 47.3 45.2 51.7 49.4 56.1 53.6 61.8 58.8 68.2 65.1 74.8 71.4 82.5 78.8 90.2 86.1 100.0 95.50 http://www.luguang.cn 10 10 10 10 10 10 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 5.50 5.80 6.05 6.40 6.63 7.02 7.37 7.78 8.10 8.55 8.92 9.40 9.72 10.2 10.5 11.1 12.1 12.8 12.9 13.6 14.5 15.3 16.2 17.1 17.8 18.8 19.4 20.5 21.8 23.1 24.3 25.6 26.8 28.2 29.1 30.8 31.6 33.3 34.8 36.8 38.1 40.2 41.3 43.6 45.4 47.8 50.2 53.0 55.1 58.1 60.7 64.1 66.4 70.1 73.7 77.8 1000 1000 500 500 200 200 50 50 10 10 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 145 150 134 139 126 130 114 117 105 108 97 100 91 94 82 86 71 74 67 70 59 60 54 56 49 51 45 47 40 42 36 38 33 34 30 31 27 29 25 26 23 24 21 22 19 20 17 18 16 17 14 15 13 13.9 12 12.6 10.8 10.5 11.7 11.3 12.5 12.1 13.8 13.4 15.0 14.5 16.2 15.6 17.3 16.7 19.0 18.2 22.0 21.2 23.5 22.5 26.5 25.2 29.1 27.7 31.9 30.6 34.7 33.2 39.1 37.5 43.5 41.4 47.7 45.7 52.0 49.9 56.4 53.9 61.9 59.3 67.8 64.8 73.5 70.1 80.5 77.0 89.0 85.0 98.0 92.0 108.0 103.0 118.0 113.0 131.0 125.0 mail:[email protected] 0.057 0.057 0.061 0.061 0.065 0.065 0.068 0.068 0.073 0.073 0.075 0.075 0.078 0.078 0.081 0.081 0.084 0.084 0.086 0.086 0.088 0.088 0.090 0.090 0.092 0.092 0.094 0.094 0.096 0.096 0.097 0.097 0.098 0.098 0.099 0.099 0.100 0.100 0.101 0.101 0.101 0.101 0.102 0.102 0.103 0.103 0.104 0.104 0.104 0.104 0.105 0.105 0.105 0.105 0.106 0.106 1.5SMC SERIES 1500 Watts Surface Mount Transient Voltage Suppressor ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Voltage Stand-Off Maximum Maximum Maximum Maximum NUMBER Device VBR Test Current Voltage Reverse Leakage Peak Surge Clamping Temperature GENERAL (Volts) (Note 1) @IT(mA) VWM at Vwm Current IPPM Voltage at IPPM Coefficient PART Marking O Min Max (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C) Code 1.5SMC100 90.0 110.0 1.0 81.0 5.0 10.9 144.0 0.106 1.5SMC100 1.5SMC100A 1.5SMC100A 95.0 105.0 1.0 85.5 5.0 11.4 137.0 0.106 1.5SMC110 99.0 121.0 1.0 89.2 5.0 9.9 158.0 0.107 1.5SMC110 1.5SMC110A 1.5SMC110A 105.0 116.0 1.0 94.0 5.0 10.3 152.0 0.107 1.5SMC120 108.0 132.0 1.0 97.2 5.0 9.1 173.0 0.107 1.5SMC120 1.5SMC120A 1.5SMC120A 114.0 126.0 1.0 102.0 5.0 9.5 165.0 0.107 1.5SMC130 117.0 143.0 1.0 106.0 5.0 8.4 187.0 0.107 1.5SMC130 1.5SMC130A 1.5SMC130A 124.0 137.0 1.0 111.0 5.0 8.7 179.0 0.107 1.5SMC150 135.0 165.0 1.0 121.0 5.0 7.3 215.0 0.108 1.5SMC150 1.5SMC150A 1.5SMC150A 143.0 158.0 1.0 128.0 5.0 7.6 207.0 0.108 1.5SMC160 144.0 176.0 1.0 130.0 5.0 6.8 230.0 0.108 1.5SMC160 1.5SMC160A 1.5SMC160A 152.0 168.0 1.0 136.0 5.0 7.1 219.0 0.108 Notes: 1.5SMC170 153.0 187.0 1.0 138.0 5.0 6.4 244.0 0.108 1.5SMC170 1.5SMC170A 1.5SMC170A 162.0 179.0 1.0 145.0 5.0 6.7 234.0 0.108 1.5SMC180 162.0 198.0 1.0 146.0 5.0 6.1 258.0 0.108 1.5SMC180 1.5SMC180A 1.5SMC180A 171.0 189.0 1.0 154.0 5.0 6.4 246.0 0.108 4. For bidirectional use C or CA suffix for types 1.5SMC 6.8 through 1.5SMC200A. 1.5SMC200 180.0 220.0 1.0 162.0 5.0 5.4 287.0 0.108 1.5SMC200 5. All terms and symbols are consistent with ANSI/IEEE C62.35. 1.5SMC200A 1.5SMC200A 190.0 210.0 1.0 171.0 5.0 5.7 274.0 0.108 1. VBR measured after IT applied for 300us, IT =square wave pulse or equivalent. 2. Surge current waveform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. http://www.luguang.cn - 545 - mail:[email protected]