SMCG SERIES 1500 Watts Surface Mount Transient Voltage Suppressor DO-215AB Cathode Band Features 0.280 (7.11) 0.260 (6.60) 0.016 (0.41) 0.006 (0.15) 0.058 (1.47) 0.038 (0.97) 0.020 (0.51) Max. 0.040 (1.02) 0.024 (0.61) 0.400 (10.16) 0.380 (9.64) Mechanical Data 0.245 (6.22) 0.220 (5.59) 0.125 (3.17) 0.115 (2.92) For surface mounted application in order to optimize board space Low profile package Built-in strain relief Glass passivated junction Excellent clamping capability Fast response time: Typically less than 1.0ps from 0 volt to BV min. Typical IR less than 1μA above 10V High temperature soldering guaranteed: 260oC / 10 seconds at terminals Plastic material used carries Underwriters Laboratory Flammability Classification 94V-0 1500 watts peak pulse power capability with a 10 x 1000 us waveform by 0.01% duty cycle Dimensions in inches and (millimeters) Case: DO-215AB Molded plastic Terminals: Solder plated Polarity: Indicated by cathode band Weight: 0.21gram Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Type Number Symbol PPK PM(AV) Value Minimum 1500 6.5 Units Watts W Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 2, 3) - Unidirectional Only IFSM 200 Amps Thermal Resistance Junction to Ambient Air (Note 4) RθJA Thermal Resistance Junction to Leads RθJL 50 15 -55 to + 150 o Peak Power Dissipation at TA=25 C, Tp=1ms ( Note 1) o Power Dissipation on Intinite Heatsink, TA=50 C o o C/W C/W o C Operating and Storage Temperature Range TJ, TSTG o 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25 C Per Fig. 2. Notes: 2 2. Mounted on 8.0mm (.013mm Thick) Copper Pads to Each Terminal. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minute Maximum. 4. Mounted on 5.0mm2(.013mm thick) land areas. Devices for Bipolar Applications 1. For Bidrectional Use C or CA Suffix for Types SMCG6.8 through Types SMCG200A. 2. Electrical Characteristics Apply in Both Directions. http://www.luguang.cn - 542 - mail:[email protected] SMCG SERIES 1500 Watts Surface Mount Transient Voltage Suppressor RATINGS AND CHARACTERISTIC CURVES (SMCG SERIES) FIG.2- PULSE DERATING CURVE FIG.1- PEAK PULSE POWER RATING CURVE 10 1 0.1 0.1 s 1 s 10 s 100 s 1.0ms 10ms DERATING IN PERCENTAGE. % 200 NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG.3 O TA = 25 C PEAK PULSE POWER (PPP) or CURRENT (IPPM) PPPM, PEAK PULSE POWER, KW 100 150 100 50 0 0 tp, PULSE WIDTH, sec. 50 75 100 125 150 175 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY 150 Peak Value IPPM 100 PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS to 50% of IPPM Half Value - IPPM 2 10/1000 sec. WAVEFORM as DEFINED by R.E.A. 50 td 0 IFSM, PEAK FORWARD SURGE CURRENT, AMPERES 200 tr = 10 sec 8.3ms Single Half Sine Wave JEDEC Method Tj=Tj max. 100 10 0 1.0 2.0 3.0 4.0 t, TIME, ms 1 10 100 NUMBER OF CYCLES AT 60Hz FIG.5- TYPICAL JUNCTION CAPACITANCE UNIDIRECTIONAL 10000 UNIDIRECTIONAL BIDIRECTIONA CJ, JUNCTION CAPACITANCE. (pF) 200 O TA, AMBIENT TEMPERATURE. ( C) FIG.3- CLAMPING POWER PULSE WAVEFORM PEAK PULSE CURRENT - % 25 VR=0 1000 O Tj = 25 C f=1.0MHz Vsig=50mVp-p 100 VR-RATED STAND-OFF VOLTAGE 10 1 10 100 200 V(BR), BREAKDOWN VOLTAGE. VOLTS http://www.luguang.cn mail:[email protected] Version: B07 SMCG SERIES 1500 Watts Surface Mount Transient Voltage Suppressor ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) GENERAL PART NUMBER SMCG6.8 SMCG6.8A SMCG7.5 SMCG7.5A SMCG8.2 SMCG8.2A SMCG9.1 SMCG9.1A SMCG10 SMCG10A SMCG11 SMCG11A SMCG12 SMCG12A SMCG13 SMCG13A SMCG15 SMCG15A SMCG16 SMCG16A SMCG18 SMCG18A SMCG20 SMCG20A SMCG22 SMCG22A SMCG24 SMCG24A SMCG27 SMCG27A SMCG30 SMCG30A SMCG33 SMCG33A SMCG36 SMCG36A SMCG39 SMCG39A SMCG43 SMCG43A SMCG47 SMCG47A SMCG51 SMCG51A SMCG56 SMCG56A SMCG62 SMCG62A SMCG68 SMCG68A SMCG75 SMCG75A SMCG82 SMCG82A SMCG91 SMCG91A Stand-Off Maximum Maximum Maximum Maximum Breakdown Voltage Test Current Voltage Reverse Leakage Peak Surge Clamping Temperature VBR @IT(mA) VWM at Vwm Current IPPM Voltage at IPPM Coefficient (Volts) (Note 1) O Min Max (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C) 6.12 6.45 6.75 7.13 7.38 7.79 8.19 8.65 9.00 9.50 9.90 10.5 10.8 11.4 11.7 12.4 13.5 14.3 14.4 15.2 16.2 17.1 18.0 19.0 19.8 20.9 21.6 22.8 24.3 25.7 27.0 28.5 29.7 31.4 32.4 34.2 35.1 37.1 38.7 40.9 42.3 44.7 45.9 48.5 50.4 53.2 55.8 58.9 61.2 64.6 67.5 71.3 73.8 77.9 81.9 86.5 7.48 7.14 8.25 7.88 9.02 8.61 10.0 9.55 11.0 10.5 12.1 11.6 13.2 12.6 14.3 13.7 16.5 15.8 17.6 16.8 19.8 18.9 22.0 21.0 24.2 23.1 26.4 25.2 29.7 28.4 33.0 31.5 36.3 34.7 39.6 37.8 42.9 41.0 47.3 45.2 51.7 49.4 56.1 53.6 61.8 58.8 68.2 65.1 74.8 71.4 82.5 78.8 90.2 86.1 100.0 95.50 http://www.luguang.cn 10 10 10 10 10 10 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 5.50 5.80 6.05 6.40 6.63 7.02 7.37 7.78 8.10 8.55 8.92 9.40 9.72 10.2 10.5 11.1 12.1 12.8 12.9 13.6 14.5 15.3 16.2 17.1 17.8 18.8 19.4 20.5 21.8 23.1 24.3 25.6 26.8 28.2 29.1 30.8 31.6 33.3 34.8 36.8 38.1 40.2 41.3 43.6 45.4 47.8 50.2 53.0 55.1 58.1 60.7 64.1 66.4 70.1 73.7 77.8 1000 1000 500 500 200 200 50 50 10 10 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 145 150 134 139 126 130 114 117 105 108 97 100 91 94 82 86 71 74 67 70 59 60 54 56 49 51 45 47 40 42 36 38 33 34 30 31 27 29 25 26 23 24 21 22 19 20 17 18 16 17 14 15 13 13.9 12 12.6 10.8 10.5 11.7 11.3 12.5 12.1 13.8 13.4 15.0 14.5 16.2 15.6 17.3 16.7 19.0 18.2 22.0 21.2 23.5 22.5 26.5 25.2 29.1 27.7 31.9 30.6 34.7 33.2 39.1 37.5 43.5 41.4 47.7 45.7 52.0 49.9 56.4 53.9 61.9 59.3 67.8 64.8 73.5 70.1 80.5 77.0 89.0 85.0 98.0 92.0 108.0 103.0 118.0 113.0 131.0 125.0 mail:[email protected] 0.057 0.057 0.061 0.061 0.065 0.065 0.068 0.068 0.073 0.073 0.075 0.075 0.078 0.078 0.081 0.081 0.084 0.084 0.086 0.086 0.088 0.088 0.090 0.090 0.092 0.092 0.094 0.094 0.096 0.096 0.097 0.097 0.098 0.098 0.099 0.099 0.100 0.100 0.101 0.101 0.101 0.101 0.102 0.102 0.103 0.103 0.104 0.104 0.104 0.104 0.105 0.105 0.105 0.105 0.106 0.106 SMCG SERIES 1500 Watts Surface Mount Transient Voltage Suppressor ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) NUMBER GENERAL PART Breakdown Voltage Stand-Off Maximum Maximum Maximum Maximum VBR Test Current Voltage Reverse Leakage Peak Surge Clamping Temperature (Volts) (Note 1) @IT(mA) VWM at Vwm Current IPPM Voltage at IPPM Coefficient O Min Max (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / C) SMCG100 90.0 110.0 1.0 81.0 5.0 SMCG100A 95.0 105.0 1.0 85.5 5.0 SMCG110 99.0 121.0 1.0 89.2 5.0 SMCG110A 105.0 116.0 1.0 94.0 5.0 SMCG120 108.0 132.0 1.0 97.2 5.0 SMCG120A 114.0 126.0 1.0 102.0 5.0 SMCG130 117.0 143.0 1.0 106.0 5.0 SMCG130A 124.0 137.0 1.0 111.0 5.0 SMCG150 135.0 165.0 1.0 121.0 5.0 SMCG150A 143.0 158.0 1.0 128.0 5.0 SMCG160 144.0 176.0 1.0 130.0 5.0 SMCG160A 152.0 168.0 1.0 136.0 5.0 Notes: SMCG170 153.0 187.0 1.0 138.0 5.0 SMCG170A 162.0 179.0 1.0 145.0 5.0 SMCG180 162.0 198.0 1.0 146.0 5.0 SMCG180A 171.0 189.0 1.0 154.0 5.0 4. SMCG200 For bidirectional use C or CA suffix for types 1.5SMC 6.8 through 1.5SMC200A. 180.0 220.0 1.0 162.0 5.0 5. SMCG200A All terms and symbols are consistent with ANSI/IEEE C62.35. 190.0 210.0 1.0 171.0 5.0 10.9 11.4 9.9 10.3 9.1 9.5 8.4 8.7 7.3 7.6 6.8 7.1 6.4 6.7 6.1 6.4 5.4 5.7 144.0 137.0 158.0 152.0 173.0 165.0 187.0 179.0 215.0 207.0 230.0 219.0 244.0 234.0 258.0 246.0 287.0 274.0 1. VBR measured after IT applied for 300us, IT =square wave pulse or equivalent. 2. Surge current waveform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. http://www.luguang.cn - 545 - mail:[email protected] 0.106 0.106 0.107 0.107 0.107 0.107 0.107 0.107 0.108 0.108 0.108 0.108 0.108 0.108 0.108 0.108 0.108 0.108