XFP-10GD-IR2 Datasheet

Optical Communications Systems™
Datasheet
10 Gbps 40 km XFP Transceivers
XFP-10GD-IR2
Highlights
XFP transceiver
Data Rates: 9.952 - 11.09 Gbps
Protocols:
- 10 Gigabit Ethernet
- 10 Gigabit Fibre Channel
- SONET OC-192/STM-64
- SONET OC-192/STM-64 over FEC
Single-mode fiber
1550 nm
12 to 40 km range
Duplex LC connector
Digital Diagnostics (SFF-8472)
XFI Loopback
Hot-swap
Overview
MRV Communications’ XFP transceivers provide the high speeds and compact dimensions that today’s demanding
networks require while delivering the deployment flexibility and inventory control that network administrators demand.
Designed to Multi-Source Agreement (MSA) standards for broadest compatibility, they perfectly match MRV’s wide range
of optical transport solutions.
Visit the MRV website at www.mrv.com or contact your nearest authorized MRV Communications dealer for more
information.
Specifications Overview
Data Rate
9.952 - 11.09 Gbps
Tx Wavelength
1550 nm
Tx Power (Minimum)
-1 dBm
Tx Dispersion Penalty
2 dB
Tx Disable
Yes
Rx Wavelength Range
1530 - 1565 nm
Rx Sensitivity
-16 dBm
Rx Saturation
-1 dBm
Operating Temperature Range
0 to 70 ºC
Power Consumption
2.65 Watts
1
Optical Communications Systems™
Datasheet
Optical Specifications
Parameter
Symbol
Minimum
Maximum
Unit
Notes
DR
9.953
11.1
Gbps
-
C
1530
1565
nm
-
POUT
-1
2
dBm
1
Operating Data Rate
Center Wavelength
Transmitter
Average Output Power
Spectral Width
Δλ
-
1
nm
-
SMSR
30
-
dB
-
Extinction Ratio
ER
8.2
-
dB
2
Dispersion Penalty
DP
-
2
dB
2
Side Mode Suppression Ratio
Optical Eye Mask
Compliant with ITU-T G.691 and GR-253-CORE
-
Receiver
Sensitivity
PIN
-
-16
dBm
3
Saturation
PIN
-1
-
dBm
3
LOS Assert
LOSA
-25
-
dBm
-
LOS De-Assert
LOSD
-
-15
dBm
-
LOS Hysteresis
-
1
4
dB
-
Reflectance
-
-
-27
dB
-
Notes:
The optical power is launched into SMF.
Measured with a PRBS 231-1 test pattern @9.953 Gbps.
Measured with a PRBS 231-1 test pattern @9.953 Gbps, BER ≤ 10-12
1.
2.
3.
Monitoring Specifications
Data Address
Parameter
Range
Accuracy
Notes
96-97
Temperature
-10 to 80 °C
± 3 °C
-
100-101
Bias Current
0 to 100 mA
± 10 %
-
102-103
TX Power
-2 to 3 dBm
± 2 dB
-
104-105
RX Power
-18 to 0 dBm
± 2 dB
-
106-107
VCC5 Voltage
+4.5 V to +5.5 V
±3%
-
108-109
VCC3 Voltage
+3.0 V to +3.7 V
±3%
-
Absolute Maximum Rating
Parameter
Symbol
Min.
Max.
Unit
Notes
Supply Voltage (3.3V)
VCC3
-0.5
4.0
V
-
Supply Voltage (5.0V)
VCC5
-0.5
6.0
V
-
Operating Relative Humidity
RH
-
85
%
-
Storage Temperature
Ts
-40
85
°C
-
Symbol
Min
Max
Unit
Notes
Recommended Operation Conditions
Parameter
TC
0
70
°C
-
Power Supply Voltage (3.3V)
VCC3
3.13
3.47
V
-
Power Supply Voltage (5V)
VCC5
4.75
5.25
V
-
Power Supply Current (3.3V)
ICC3
-
750
mA
-
Power Supply Current (5V)
ICC5
-
200
mA
-
Operating Temperature (Case)
Power Dissipation
PD
-
3.5
W
-
Data Rate
DR
9.953
11.1
Gbps
-
2
Optical Communications Systems™
Datasheet
Electrical Specifications
Parameter
Symbol
Minimum
Maximum
Unit
Notes
High-Speed Signal (CML) Interface Specification
Input Data Rate
-
9.953
11.1
Gbps
-
Differential Data Input Amplitude 1
-
120
1000
mVpp
1
Input Differential Impedance
-
80
120
Ω
-
Output Data Rate
-
9.953
11.1
Gbps
-
Differential Data Output Amplitude 1
-
500
800
mVpp
1
Output Differential Impedance
-
80
120
Ω
-
-
2.0
Vdd1=3.3
V
-
Input Low Voltage
-
GND
0.8
V
-
Output High Voltage
-
2.4
Vdd1=3.3
V
-
Output Low Voltage
-
GND
0.4
V
-
fSCL
-
400
kHz
-
Low-Speed Signal (LVTTL) Interface Specification
Input High Voltage
2-Wire Serial Interface(LVTTL) Specification
Clock Frequency
Reference Clock Interface Specification
No Reference Clock Needed
Notes:
1.
Internally AC coupled.
Host Board Connector Pinout
3
Optical Communications Systems™
Datasheet
Host Board Connector Legend
Pin
Logic
1
2
Symbol
Name/Description
Note
GND
Module Ground
1
VEE5
Optional -5.2V power supply (Not Implemented)
3
LVTTL-I
Mod_DeSel
Module De-Select; when held low allows module to respond to 2-wire serial interface
4
LVTTL-O
Interrupt
Interrupt; indicates presence of an important condition which can be read over the 2-wire
serial interface
5
LVTTL-I
TX_DIS
Transmitter Disable; turns off transmitter laser output
6
VCC5
+5 V Power Supply
7
GND
Module Ground
8
VCC3
+3.3 V Power Supply
9
VCC3
+3.3 V Power Supply
2
1
10
LVTTL-I/O
SCL
2-Wire Serial Interface Clock
2
11
LVTTL-I/O
SDA
2-Wire Serial Interface Data Line
2
12
LVTTL-O
Mod_Abs
Indicates module is not present. Grounded in the module
2
13
LVTTL-O
Mod_NR
Module Not Ready; indicating module operational fault
2
14
LVTTL-O
RX_LOS
Receiver Loss of Signal Indicator
2
15
GND
Module Ground
1
16
GND
Module Ground
1
17
CML-O
RD-
Receiver Inverted Data Output
18
CML-O
RD+
Receiver Non-Inverted Data Output
19
GND
Module Ground
1
20
VCC2
+1.8 V Power Supply (Not Implemented)
3
21
LVTTL-I
22
P_Down/RST
VCC2
23
Power Down; When high, requires the module to limit power consumption to 1.5 W or
below. 2-wire serial interface must be functional in the low power mode.
Reset; the falling edge initiates a complete reset of the module including the 2-wire serial
interface, equivalent to a power cycle.
+1.8 V Power Supply (Not Implemented)
3
GND
Module Ground
1
24
PECL-I
RefCLK+
Not used, internally terminated to 50 ohm (100 ohm diff ).
4
25
PECL-I
RefCLK-
Not used, internally terminated to 50 ohm (100 ohm diff ).
4
GND
Module Ground
1
1
26
27
GND
Module Ground
28
CML-I
TD-
Transmitter Inverted Data Input
29
CML-I
TD+
Transmitter Non-Inverted Data Input
GND
Module Ground
30
Notes:
1.
2.
3.
4.
Module ground pins GND are isolated from the module case and chassis ground within the module.
Shall be pulled up with 4.7 K-10 Kohms to a voltage between 3.15 V and 3.45 V on the host board.
The pins are open within module.
Reference Clock is not required.
4
1
Optical Communications Systems™
Datasheet
Mechanical Drawing
LABEL
Data Rate
Wavelength
(nm)
Dispersion
Penalty
(dB)
Bail Latch
Color
Distance
(km)
OC192/STM-64, OC192/STM-64 over FEC, 10GE or 10G FC,
single-mode XFP transceiver with Digital Diagnostics.
9.953 - 11.1 Gbps
1550
2.0
Magenta
12 -40
Model
Description
Ordering Information
XFP-10GD-IR2
Regulatory and Industry Compliances
Class 1 Laser Product, complies with EN 60825-1 and 21 CFR 1040.10 except for deviations pursuant to Laser Notice No. 50. dated June 24, 2007
MSA INF-8077i; Digital Diagnostic SFF-8472
Certified by one or more of the following agencies: TÜV, UL, CSA;
RoHS Directive; China RoHS; California RoHS Law, REACH Directive SVHC; WEEE Directive
The Quality Management System is certified to ISO 9001 by QMI-SAI Global
The Environmental Management System is in compliance with ISO 14001
Warnings
Handling Precautions: This device is susceptible to damage as a result of electrostatic descharge (ESD). A static free environment is highly
recommended. Follow guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
MRV has more than 50 offices throughout the world. Addresses, phone numbers and fax numbers are listed at www.mrv.com.
Please e-mail us at [email protected] or call us for assistance.
MRV Los Angeles
20415 Nordhoff Street
Chatsworth, CA 91311
800-338-5316
818-773-0900
MRV Boston
300 Apollo Drive
Chelmsford, MA 01824
800-338-5316
978-674-6800
MRV International
Business Park Moerfelden
Waldeckerstrasse 13
64546 Moerfelden-Walldorf
Germany
Tel. (49) 6105/2070
Fax (49) 6105/207-100
All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the
accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. Please contact MRV Communications for more information.
MRV Communications and the MRV Communications logo are trademarks of MRV Communications, Inc. Other trademarks are the property of their respective holders.
MRV-OP-XFP10GDIR2-080610
3020070-001 Rev. A2
Copyright ©2010 MRV Communications, Inc. All Rights Reserved.