Datasheet 10 Gbps DWDM Multirate XFP Transceivers 9.95 Gbps - 11.1 Gbps Features Models for all C-band wavelengths on the 100GHz DWDM ITU grid Cold start up wavelength compliance (stable transmit frequency) 120 km with EDC, 80 km, and 40 km reach models XFI high-speed electrical interface 9.95 Gbps, 10.31 Gbps, 10.52 Gbps, 10.7 Gbps, and 11.1 Gbps support Digital Diagnostics Cooled EML with isolator APD receiver (120 km and 80 km) and PIN receiver (40 km) Power consumption under 3.5 watts -5° to 70° C operating temperature range XFP MSA Rev 4.5 compliance RoHS and China RoHS compliance Class 1 Laser, 21CFR 1040.10/1040.11 compliance EN 60825-1/A1:2002 compliance USA and Canada UL listing External reference clock synchronization Absolute Maximum Rating Parameter Symbol Min. Typical Max. Unit Maximum Supply Voltage (3.3V) Vcc3 -0.3 - 3.6 V Maximum Supply Voltage (5.0V) Vcc5 -0.3 - 5.5 V Maximum Supply Voltage (1.8V) Vcc2 -0.3 - 2 V Operating Temperature (case) BR 9.95 - 11.1 Gb/s Storage Temperature Tst -40 - 85 °C General Operations Parameter Symbol Min Typical Max Unit Supply Voltage (1.8V) Vcc2 1.71 1.8 1.89 V Supply Voltage (3.3V) Vcc3 3.14 3.3 3.47 V Supply Voltage (5V) Vcc5 4.75 5 5.25 V Icc - - 500 mA Inrush Current (1.8V) Iinrush2 - - 1 A Inrush Current (3.3V) Iinrush3 - - 0.75 A Inrush Current (5V) Iinrush5 - - 0.5 A Total Current on Any Pin Module Current Ramp Rate - - - 100 mA/μS Power on 1.8V Rail P2rail - - 1.8 W Power on 3.3V Rail P3rail - - 2.5 W Power on 5V Rail P5rail - - 2.5 W Pt - - 3.5 W Module Total Power Consumption Power Consumption-P_Down Mode Pp_d Power Supply Noise Rejection PSNR Compliant to Section 2.7.2 of XFP MSA - 1 Datasheet Transmitter Specifications (Electical) Parameter Symbol Min Typical Max Unit Input Differential Impedence Rin - 100 - Ω Differential Data Input Swing Vin,p-p 120 - 820 mV TxDisable_Disable Vd 2 - Vcc3 V TxDisable_Enable Ven GND - GND+0.8 V Symbol Min Typical Max Unit -2 0 2 dBm Transmitter Specifications (Optical) Parameter Output Power: XFP-DWLR12P-xx PO XFP-DWLR08P-xx PO 0 2 4 dBm XFP-DWIR04P-xx PO -1 0.5 2 dBm dBm Average Launch Power Tx_Off Poff - - -30 Extinction Ratio: XFP-DWLR12P-xx ER 8.2 - - dB XFP-DWLR08P-xx ER 9 - - dB XFP-DWIR04P-xx ER 8.2 - - dB ITU-T G.691, Telecordia GR-253-CORE, IEEE802.3 10GBASE-ZR Compliant Eye Mask Side Mode Suppression Ratio SMSR 30 - Center Wavelength λ Channel Spacing Δf - 100 - ITU Grid dB nm - GHz Δλ20 - - 1 nm Jitter Generation (peak-to-peak) Jgen(pk-pk) - - 0.1 UI Jitter Generation (RMS) Spectral Width Jgen(RMS) - - 0.01 UI Dispersion Penalty at 2200 ps/nma DP - - 2 dB Relative Intensity Noise RIN - - -130 dB/Hz Reflectance Tolerance ref T - - -27 dB Symbol Min Typical Max Unit Zd - 100 - Ω Vout,p-p 340 - 850 mV tr 24 - - ps ps Receiver Specifications (Electrical) Parameter Reference Differential Output Impedence Differential Data Output Swing Output Rise Time, 20-80% Output Fall Time, 20-80% LOS Fault LOS Normal tf 24 - - VLOS_fault host_Vcc3 - 0.5 - host_Vcc3 V VLOS_normal GND - GND + 0.4 V 2 Datasheet Receiver Specifications (Optical) Parameter Sensitivity (9.95 Gb/s): Sensitivity (10.7 Gb/s): Saturation: Symbol Min Typical Max Unit XFP-DWLR12P-xxa Rxsens995 - - -24 dBm XFP-DWLR08P-xxb Rxsens995 - - -24 dBm XFP-DWIR04P-xxb Rxsens995 - - -16 dBm XFP-DWLR12P-xxa Rxsens1070 - - -23 dBm XFP-DWLR08P-xxb Rxsens1070 - - -23 dBm XFP-DWIR04P-xxb Rxsens1070 - - -15 dBm XFP-DWLR12P-xxa Rx OL -7 - - dBm XFP-DWLR08P-xxb Rx OL -7 - - dBm XFP-DWIR04P-xxb Rx OL 0 - - dBm λ 1528 - 1564 nm ORL - - -27 dB XFP-DWLR12P-xx - -34 - - dBm XFP-DWLR08P-xx - -34 - - dBm XFP-DWIR04P-xx - -24 - - dBm Wavelengthc Optical Return Loss LOS Assert: LOS De-assert: XFP-DWLR12P-xx - - - -24 dBm XFP-DWLR08P-xx - - - -24 dBm XFP-DWIR04P-xx - - - -16 dBm - 0.5 - - dB Symbol Min Typical Max Unit Zd 80 100 120 Ω Differential Input Clock Amplitude (p-p) - 640 - 1600 mV Reference Clock Duty Cycle - 40 - 60 % Tr/Tf 200 - 1250 ps f0 - Baud/64 - MHz LOS Hysteresis a) At 8.2dB ER, 1e-12 BER, 231-1 PRBS, back to back b) At 9dB ER, 1e-12 BER, 231-1 PRBS, back to back c) Operational over 1200 - 1625 nm range Reference Clock Parameter Clock Differential Input Impedance Reference Clock Rise/Fall Time (20%-80%) Reference Clock Frequency 3 Datasheet Data Rate Wavelength (nm) Dispersion Penalty (dB) Dispersion Spec. (ps/nm) Bail Latch Color Distance (km) XFP-DWLR12P-xx* 10 Gbps DWDM Multirate XFP Tranceiver with Digital Diagnostics 9.95 - 11.1 Gbps ITU Grid 2 2200 White 120** XFP-DWLR08P-xx* 10 Gbps DWDM Multirate XFP Tranceiver with Digital Diagnostics 9.95 - 11.1 Gbps ITU Grid 2 1600 White 80 XFP-DWIR04P-xx* 10 Gbps DWDM Multirate XFP Tranceiver with Digital Diagnostics 9.95 - 11.1 Gbps ITU Grid 2 800 White 40 Model Description Ordering Information * See Wavelength Guide below for “xx” values ** EDFA is required for full distance reach λc Wavelength Guide ITU Channel (xx) Frequency (THz) Wavelength (nm) ITU Channel (xx) Frequency (THz) Wavelength (nm) 17 191.7 1563.863 40 194.0 1545.322 18 191.8 1563.047 41 194.1 1544.526 19 191.9 1562.233 42 194.2 1543.730 20 192.0 1561.419 43 194.3 1542.936 21 192.1 1560.606 44 194.4 1542.142 22 192.2 1559.794 45 194.5 1541.349 23 192.3 1558.983 46 194.6 1540.557 24 192.4 1558.173 47 194.7 1539.766 25 192.5 1557.363 48 194.8 1538.976 26 192.6 1556.555 49 194.9 1538.186 27 192.7 1555.747 50 195.0 1537.397 28 192.8 1554.940 51 195.1 1536.609 29 192.9 1554.134 52 195.2 1535.822 30 193.0 1553.329 53 195.3 1535.036 31 193.1 1552.524 54 195.4 1534.250 32 193.2 1551.721 55 195.5 1533.465 33 193.3 1550.918 56 195.6 1532.681 34 193.4 1550.116 57 195.7 1531.898 35 193.5 1549.315 58 195.8 1531.116 36 193.6 1548.515 59 195.9 1530.334 37 193.7 1547.715 60 196.0 1529.553 38 193.8 1546.917 61 196.1 1528.773 39 193.9 1546.119 4 Datasheet Pin Out Definition Pin Logic 1 Symbol Name/Description Note GND Module Ground 1 VEE5 Optional -5.2V power supply (not used) 3 LVTTL-I Mod_DeSel Module De-Select; when held low allows module to respond to 2-wire interface interface 4 LVTTL-O Interrupt Interrupt; indicates presence of an important condition which can be read over the 2-wire serial interface 5 LVTTL-I 2 TX_DIS Transmitter Disable; turns off transmitter laser output 6 Vcc5 +5 V Power Supply 7 GND Module Ground 8 Vcc3 +3.3 V Power Supply 9 Vcc3 +3.3 V Power Supply 2 1 10 LVTTL-I/O SCL 2-Wire Serial Interface Clock 2 11 LVTTL-I/O SDA 2-Wire Serial Interface Data Line 2 12 LVTTL-O Mod_Abs Indicates module is not present. Grounded in the module 2 13 LVTTL-O Mod_NR Module Not Ready; indicating module operational fault 2 14 LVTTL-O RX_LOS Receiver Loss of Signal Indicator 2 15 GND Module Ground 1 16 GND Module Ground 1 17 CML-O RD- Receiver Inverted Data Output 18 CML-O RD+ Receiver Non-Inverted Data Output 19 GND Module Ground 20 Vcc2 21 LVTTL-I P_Down/RST +1.8 V Power Supply Power Down; When high, requires the module to limit power consumption to 1.5 W or below. 2-wire serial interface must be functional in the low power mode. Reset; the falling edge initiates a complete rest of the module including the 2-wire serial interface, equivalent to a power cycle. Vcc2 22 1 +1.8 V Power Supply GND Module Ground 24 PECL-I RefCLK+ Reference Clock Non-Inverted Input, AC coupled on the host board 25 PECL-I RefCLK- Reference Clock Inverted Input, AC coupled on the host board GND Module Ground 1 1 23 26 27 GND Module Ground 28 CML-I TD- Transmitter Inverted Data Input 29 CML-I TD+ Transmitter Non-Inverted Data Input GND Module Ground 30 Note: 1. Module ground pins GND are isolated from the module case and chassis ground within the module. 2. Shall be pulled up with 4.7k-10kohms to a voltage between 3.15 V and 3.45 V on the host board. 5 1 1 Datasheet Mechanical Drawing [6.91] .272 [16.15] .636 [69.09] 2.720 [8.95] [8.44] .352 .332 [11.47] .451 [3.80] .150 [6.02] .237 [18.29] .720 [6.25] .246 [12.19] .480 [77.98] 3.070 - ISO VIEW 1. MRV'S XFP TRANSCEIVERS ARE COMPLIANT WITH THE DIMENSIONS DEFINED BY XFP MULTISOURCING AGREEMENT (MSA). NOTES: UNLESS OTHERWISE SPECIFIED Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: High power spectral laser emission is deemed dangerous to human eyes. Always avoid direct and indirect eye exposuers. MRV has more than 50 offices throughout the world. Addresses, phone numbers and fax numbers are listed at www.mrv.com. Please e-mail us at [email protected] or call us for assistance. MRV Los Angeles 20415 Nordhoff St. Chatsworth, CA 91311 800-338-5316 818-773-0900 MRV Boston 295 Foster St. Littleton, MA 01460 800-338-5316 978-952-4700 MRV International Business Park Moerfelden Waldeckerstrasse 13 64546 Moerfelden-Walldorf Germany Tel. (49) 6105/2070 Fax (49) 6105/207-100 All statements, technical information and recommendations related to the products herein are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. Please contact MRV Communications for more information. MRV Communications and the MRV Communications logo are trademarks of MRV Communications, Inc. Other trademarks are the property of their respective holders. MRV-OP-XFPDWMR-041008 3020005-001 Rev. A2 Copyright ©2008 MRV Communications, Inc. All Rights Reserved.