EXTERNAL CAGES

EXTERNAL CAGES
for Eclipse Level Transmitters
DESCRIPTION
The Eclipse 705 is ideally suited to operate in any type of
external cage ≥ 2" (DN 50). This bulletin provides guidelines to easily retrofit any displacer transmitter in an existing external cage or to specify a suitable cage for your
Eclipse transmitter.
For ordering information about the Eclipse amplifier and
GWR probe, ask for Eclipse 705 bulletin BE 57-101.
The tradition to build cages ...
F E AT U R E S
• 2" (DN50) or 3" (DN 80) Carbon or Stainless steel cages
(other materials upon request)
• Flanged or sealed external cage
• Up to 5,7 m (224") measuring range
• Up to 345 bar (5000 psi) pressure rating
• Standard and NACE construction
• Eclipse is not affected by changing media variables such
as e.g. density, pressure, dielectrics, pH, viscosity, ...
• Easy and cost effective retrofit with a minimal of modifications to existing installations
C O N F I G U R AT I O N S
3 possible process connection styles may exist:
7EK probe
see bulletin 57-101
Side/side
cage
Side/side
Side/bottom
Top/bottom
For Top/bottom connection, see ordering information in bulletin 57-101. The 7EK probe/cage assembly is a self-contained assembly with a single model code.
D E S I G N S TA N D A R D S
OPTIONAL
•
•
•
•
•
Customized installation dimensions
Code compliance construction
Special tank connections
Extreme temperature modifications
Special exterior surface preparation and finish
PED - 97/23/EC (Pressure Equipment Directives)
NACE MR -01-75 ➀
ASME - ANSI B31.3 ➀
IBR (Indian Boiler Regulations) ➀
➀ Consult factory for proper partnumbers
Worldwide level and flow solutions
SELECTION GUIDELINES
In order to match the proper Eclipse transmitter with the proper external cage, consider the following:
- Type of application – use the applicable Eclipse GWR probe. See Eclipse 705 bulletin BE 57-101.
- Overfill proof: Overfilling occurs when the level rises above the max level – radar based equipment may provide erroneous
output in this zone unless an adapted design is used. Overfill proof GWR probes are always safe to use – only in cases
where the application demands for a different probe type, other selections should be considered and the recommended
precautions followed.
- Cage size depends on GWR probe type – see Eclipse 705 bulletin BE 57-101.
- Select the correct GWR probe length for your cage – see below drawing and guidelines.
Amplifier Type
GWR Probe type
Min cage size
Overfill considerations
7MR/7MD/7MS
2" / DN 50
None
7MT
2" / DN 50
None
7MB
3" / DN 80
Max. level should be 150 mm (6") below the body connection of
the cage
7MF/7M1
Consult factory
705
Body connection
E
20 mA / 100 %
P
Measuring range:
min 300 mm (11.81")
max 5700 mm (224")
Probe Insertion Length
4 mA / 0 %
F
min 25 mm (1")
Dimension E and P : for cages selected from this bulletin: refer to the dimensional specification tables on pages 5 and 7.
Dimension E and F : for re-use of existing cages: should be verified in the field. F is distance from 4 mA level up to bottom of cage interior minus 25 mm (1")
FOR EXISTING CAGES
Select type of GWR probe:
- Dimension E ≤ 150 mm (6") and/or cage risks overfilling: use only overfill proof GWR probes (7MR – 7MS –7MD – 7MT)
- Dimension E ≥ 150 mm (6"): all selectable probes can be used.
Define the probe length:
Probe length = Dimension E + measuring range + Dimension F
Dimensions E and F need to be verified with the existing cage.
FOR CAGES SELECTED FROM THIS BULLETIN
Select type of GWR probe:
- When cage risks overfilling: use only overfill proof GWR probes (7MR – 7MS –7MD – 7MT)
- When no overfilling can exist: all selectable probes can be used
Define the probe length:
Probe lengths are defined as per dimension
P
– see tables pages 5 and 7
Note:
If dimension F is ≤ 150 mm (6"), a transition zone with reduced accuracy may exist. The transition zone is depending the
probe type and the dielectrics of the liquid.
2
S E L E C T I O N D ATA F O R E X T E R N A L C A G E – E C L I P S E T R A N S M I T T E R S
A complete measuring system consists of:
1. Order code for Eclipse cage
Order code for modified cages: put an "X" in front of the closest matching order code and specify the
modifications/adders separately: e.g. XF2A-DA2D-100
X = material certification EN 10204 / DIN 50049-3.1.B
2. Order code for Eclipse transmitter: see bulletin BE 57-101.
1. Order code for the Eclipse cage
BASIC MODEL NUMBER
Flanged cages – select Eclipse GWR probes with pressure matching ANSI flanges
F 2 A
F 3 A
Flanged external 2" cage – fits for all except 7MB GWR probes
Flanged external 3" cage – fits for all
Sealed cages – select Eclipse GWR probes with 3/4" NPT process connection (code 11)
S 2 A
S 3 A
Sealed external 2" cage – fits for all except 7MB GWR probes
Sealed external 3" cage – fits for all except 7MB GWR probes
MATERIAL OF CONSTRUCTION
A
D
Carbon steel
316/316L (1.4401/1.4404) stainless steel
CAGE AND FLANGE RATING
A
B
C
D
E
F
150
300
600
900
1500
2500
lbs
lbs
lbs
lbs
lbs
lbs (max 345 bar (5000 psi))
1
2
3
4
5
6
7
PN
PN
PN
PN
PN
PN
PN
PROCESS CONNECTION – SIZE
2
3
4
1"
1 1/2" (no NPT/SW conn. for 2" cages)
2" (only for 3" cages)
16
25/40
63
100
160
250
320
EN 1092-1 Type B1
EN 1092-1 Type B1
EN 1092-1 Type B2
EN 1092-1 Type B2
DIN 2638 Form E
DIN 2628 Form E
DIN 2629 Form E
DIN sizes (only for flanged process connection)
B
C
D
DN 25
DN 40
DN 50 (only for 3" cages)
THREADED OR SOCKET WELD PROCESS CONNECTION
Socket weld connection
NPT connection
A
G
B
H
Side/Side
Side/bottom
Side/Side
Side/bottom
FLANGED PROCESS CONNECTION – up to 600 lbs cage rating / up to PN 100
EN/DIN Weld Neck flanges
ANSI Slip on RF flanges
D
K
1
2
Side/Side
Side/bottom
Side/Side
Side/bottom
FLANGED PROCESS CONNECTION – for 600 lbs - 2500 lbs / PN 100 - PN 320
EN/DIN Weld Neck flanges
ANSI Weld Neck RJ flanges
F
M
1
2
Side/Side
Side/bottom
Side/Side
Side/bottom
MEASURING RANGE
Inch ranges (Dimensions as per specified inch dimension)
0 0 F
0 A
14" / 356 mm
0 0 G
0 B
32" / 813 mm
0 0 H
0 C
48" / 1219 mm
0 0 I
0 D
60" / 1524 mm
0 E
72" / 1829 mm
0
0
0
0
0
84"
96"
108"
120"
/
/
/
/
2134
2438
2743
3048
mm
mm
mm
mm
Metric ranges (specify per cm increments)
0 3 0
5 7 0
A
300 mm – minimum length
5700 mm – maximum length
complete order code for ECLIPSE cage
3
2" FLANGED AND SEALED CAGES – DIMENSIONS IN MM (INCHES)
Flanged cages
ANSI body cage flanges
Select Eclipse GWR probes with pressure matching ANSI flanges
E
E
P
P
Measuring
range
(Probe
insertion
length)
Measuring
range
(Probe
insertion
length)
E
P
Measuring
range
(Probe
insertion
length)
D
D
D
B
B
B
Drain: 1" NPT
Drain: 1" NPT
Side/Side connection
NPT/Socket weld
Side/Bottom connection
ANSI RF Flange
Side/Side connection
ANSI RF Flange
Sealed cages
3/4" NPT body cage connection
Select Eclipse GWR probes with 3/4" NPT process connection
Measuring
range
P
Measuring
range
P
Measuring
range
P
(Probe
insertion
length)
(Probe
insertion
length)
(Probe
insertion
length)
E
E
E
D
D
D
B
B
Drain: 1" NPT
Side/Side connection
NPT/Socket weld
4
B
Side/Bottom connection
ANSI RF Flange
Drain: 1" NPT
Side/Side connection
ANSI RF Flange
SEALED AND FLANGED 2" EXTERNAL CAGES
D I M E N S I O N A L S P E C I F I C AT I O N S I N M M ( I N C H E S )
Sealed 2" external cage
Size
Flanged 2" external cage
Connection
B
E
D
P (Range +)
B
E
D
P (Range +)
1"
NPT - 150/300/600 lbs
55 (2.17)
178 (7.00)
200 (7.87)
314 (12.36)
55 (2.17)
150 (5.91)
200 (7.87)
300 (11.81)
1 1/2"
NPT - 150/300/600 lbs
67 (2.64)
178 (7.00)
200 (7.87)
314 (12.36)
67 (2.64)
150 (5.91)
200 (7.87)
300 (11.81)
1"
SW - 150/300/600 lbs
55 (2.17)
178 (7.00)
200 (7.87)
314 (12.36)
55 (2.17)
150 (5.91)
200 (7.87)
300 (11.81)
1 1/2"
SW - 150/300/600 lbs
67 (2.64)
178 (7.00)
200 (7.87)
314 (12.36)
67 (2.64)
150 (5.91)
200 (7.87)
300 (11.81)
1"
RF Slip on flange - 150/300/600 lbs
150 (5.91)
178 (7.00)
200 (7.87)
314 (12.36)
150 (5.91)
150 (5.91)
200 (7.87)
300 (11.81)
1 1/2"
RF Slip on flange - 150/300/600 lbs
160 (6.30)
178 (7.00)
200 (7.87)
314 (12.36)
160 (6.30)
150 (5.91)
200 (7.87)
300 (11.81)
1"
RF Slip on flange - 150/300/600 lbs
150 (5.91)
178 (7.00)
325 (12.80)
314 (12.36)
150 (5.91)
150 (5.91)
325 (12.80)
300 (11.81)
1 1/2"
RF Slip on flange - 150/300/600 lbs
160 (6.30)
178 (7.00)
335 (13.19)
314 (12.36)
160 (6.30)
150 (5.91)
335 (13.19)
300 (11.81)
1"
RJ Weld Neck flange - 600 lbs
150 (5.91)
178 (7.00)
200 (7.87)
314 (12.36)
150 (5.91)
150 (5.91)
200 (7.87)
300 (11.81)
1 1/2"
RJ Weld Neck flange - 600 lbs
160 (6.30)
178 (7.00)
200 (7.87)
314 (12.36)
160 (6.30)
150 (5.91)
200 (7.87)
300 (11.81)
1"
RJ Weld Neck flange - 900 lbs
161 (6.34)
178 (7.00)
200 (7.87)
314 (12.36)
161 (6.34)
190 (7.48)
200 (7.87)
345 (13.58)
1 1/2"
RJ Weld Neck flange - 900 lbs
173 (6.81)
178 (7.00)
200 (7.87)
314 (12.36)
173 (6.81)
190 (7.48)
200 (7.87)
345 (13.58)
1"
RJ Weld Neck flange - 1500 lbs
161 (6.34)
178 (7.00)
200 (7.87)
314 (12.36)
161 (6.34)
190 (7.48)
200 (7.87)
345 (13.58)
1 1/2"
RJ Weld Neck flange - 1500 lbs
173 (6.81)
178 (7.00)
200 (7.87)
314 (12.36)
173 (6.81)
190 (7.48)
200 (7.87)
345 (13.58)
1"
RJ Weld Neck flange - 2500 lbs
177 (6.96)
178 (7.00)
200 (7.87)
314 (12.36)
177 (6.96)
215 (8,46)
200 (7.87)
375 (14.76)
1 1/2"
RJ Weld Neck flange - 2500 lbs
203 (7.99)
178 (7.00)
200 (7.87)
314 (12.36)
203 (7.99)
215 (8,46)
200 (7.87)
375 (14.76)
1"
RJ Weld Neck flange - 600 lbs
150 (5.91)
178 (7.00)
325 (12.80)
314 (12.36)
150 (5.91)
150 (5.91)
325 (12.80)
300 (11.81)
1 1/2"
RJ Weld Neck flange - 600 lbs
160 (6.30)
178 (7.00)
335 (13.19)
314 (12.36)
160 (6.30)
150 (5.91)
335 (13.19)
300 (11.81)
1"
RJ Weld Neck flange - 900 lbs
161 (6.34)
178 (7.00)
335 (13.19)
314 (12.36)
161 (6.34)
190 (7.48)
335 (13.19)
345 (13.58)
1 1/2"
RJ Weld Neck flange - 900 lbs
173 (6.81)
178 (7.00)
350 (13.78)
314 (12.36)
173 (6.81)
190 (7.48)
350 (13.78)
345 (13.58)
1"
RJ Weld Neck flange - 1500 lbs
161 (6.34)
178 (7.00)
335 (13.19)
314 (12.36)
161 (6.34)
190 (7.48)
335 (13.19)
345 (13.58)
1 1/2"
RJ Weld Neck flange - 1500 lbs
173 (6.81)
178 (7.00)
350 (13.78)
314 (12.36)
173 (6.81)
190 (7.48)
350 (13.78)
345 (13.58)
1"
RJ Weld Neck flange - 2500 lbs
177 (6.96)
178 (7.00)
355 (13.98)
314 (12.36)
177 (6.96)
215 (8.46)
355 (13.98)
375 (14.76)
1 1/2"
RJ Weld Neck flange - 2500 lbs
203 (7.99)
178 (7.00)
380 (14.96)
314 (12.36)
203 (7.99)
215 (8.46)
380 (14.96)
375 (14.76)
DN 25
PN 16/25/40 flange EN 1092-1/ B1
150 (5.91)
178 (7.00)
200 (7.87)
314 (12.36)
150 (5.91)
150 (5.91)
200 (7.87)
300 (11.81)
DN 40
PN 16/25/40 flange EN 1092-1/ B1
160 (6.30)
178 (7.00)
200 (7.87)
314 (12.36)
160 (6.30)
150 (5.91)
200 (7.87)
300 (11.81)
DN 25
PN 63 flange EN 1092-1/ B2
170 (6.69)
178 (7.00)
200 (7.87)
314 (12.36)
170 (6.69)
150 (5.91)
200 (7.87)
300 (11.81)
DN 40
PN 63 flange EN 1092-1/ B2
180 (7.09)
178 (7.00)
200 (7.87)
314 (12.36)
180 (7.09)
150 (5.91)
200 (7.87)
300 (11.81)
DN 25
PN 100 flange EN 1092-1/ B2
170 (6.69)
178 (7.00)
200 (7.87)
314 (12.36)
170 (6.69)
150 (5.91)
200 (7.87)
300 (11.81)
DN 40
PN 100 flange EN 1092-1/ B2
180 (7.09)
178 (7.00)
200 (7.87)
314 (12.36)
180 (7.09)
150 (5.91)
200 (7.87)
300 (11.81)
DN 25
PN 160 DIN 2638 Form E
170 (6.69)
178 (7.00)
200 (7.87)
314 (12.36)
170 (6.69)
190 (7.48)
200 (7.87)
345 (13.58)
DN 40
PN 160 DIN 2638 Form E
180 (7.09)
178 (7.00)
200 (7.87)
314 (12.36)
180 (7.09)
190 (7.48)
200 (7.87)
345 (13.58)
DN 25
PN 250 DIN 2628 Form E
177 (6.96)
178 (7.00)
200 (7.87)
314 (12.36)
177 (6.96)
190 (7.48)
200 (7.87)
345 (13.58)
DN 40
PN 250 DIN 2628 Form E
196 (7.72)
178 (7.00)
200 (7.87)
314 (12.36)
196 (7.72)
190 (7.48)
200 (7.87)
345 (13.58)
DN 25
PN 320 DIN 2629 Form E
190 (7.48)
178 (7.00)
200 (7.87)
314 (12.36)
190 (7.48)
215 (8.46)
200 (7.87)
375 (14.76)
DN 40
PN 320 DIN 2629 Form E
204 (8.03)
178 (7.00)
200 (7.87)
314 (12.36)
204 (8.03)
215 (8.46)
200 (7.87)
375 (14.76)
DN 25
PN 16/25/40 flange EN 1092-1/ B1
150 (5.91)
178 (7.00)
325 (12.80)
314 (12.36)
150 (5.91)
150 (5.91)
325 (12.80)
300 (11.81)
DN 40
PN 16/25/40 flange EN 1092-1/ B1
160 (6.30)
178 (7.00)
335 (13.19)
314 (12.36)
160 (6.30)
150 (5.91)
335 (13.19)
300 (11.81)
DN 25
PN 63 flange EN 1092-1/ B2
170 (6.69)
178 (7.00)
345 (13.58)
314 (12.36)
170 (6.69)
150 (5.91)
345 (13.58)
300 (11.81)
DN 40
PN 63 flange EN 1092-1/ B2
180 (7.09)
178 (7.00)
355 (13.98)
314 (12.36)
180 (7.09)
150 (5.91)
355 (13.98)
300 (11.81)
DN 25
PN 100 flange EN 1092-1/ B2
170 (6.69)
178 (7.00)
345 (13.58)
314 (12.36)
170 (6.69)
150 (5.91)
345 (13.58)
300 (11.81)
DN 40
PN 100 flange EN 1092-1/ B2
180 (7.09)
178 (7.00)
355 (13.98)
314 (12.36)
180 (7.09)
150 (5.91)
355 (13.98)
300 (11.81)
DN 25
PN 160 DIN 2638 Form E
170 (6.69)
178 (7.00)
345 (13.58)
314 (12.36)
170 (6.69)
190 (7.48)
345 (13.58)
345 (13.58)
DN 40
PN 160 DIN 2638 Form E
180 (7.09)
178 (7.00)
355 (13.98)
314 (12.36)
180 (7.09)
190 (7.48)
355 (13.98)
345 (13.58)
DN 25
PN 250 DIN 2628 Form E
177 (6.96)
178 (7.00)
355 (13.98)
314 (12.36)
177 (6.96)
190 (7.48)
355 (13.98)
345 (13.58)
DN 40
PN 250 DIN 2628 Form E
196 (7.72)
178 (7.00)
370 (14.57)
314 (12.36)
196 (7.72)
190 (7.48)
370 (14.57)
345 (13.58)
DN 25
PN 320 DIN 2629 Form E
190 (7.48)
178 (7.00)
365 (14.37)
314 (12.36)
190 (7.48)
215 (8.46)
365 (14.37)
375 (14.76)
DN 40
PN 320 DIN 2629 Form E
204 (8.03)
178 (7.00)
380 (14.96)
314 (12.36)
204 (8.03)
215 (8.46)
380 (14.96)
375 (14.76)
Side-side
Side-bottom
Side-side
Side-bottom
Side-Side
Side-Bottom
Side-Side
Side-Bottom
Probe length Eclipse = (dimension “P” + measuring range) arounded to the nearest cm value, e.g. 1523 mm 152 cm or 1526 mm = 153 cm
5
3" FLANGED AND SEALED CAGES – DIMENSIONS IN MM (INCHES)
Flanged cages
ANSI body cage flanges
Select Eclipse GWR probes with pressure matching ANSI flanges
E
E
P
P
Measuring
range
(Probe
insertion
length)
Measuring
range
(Probe
insertion
length)
E
P
Measuring
range
(Probe
insertion
length)
D
D
D
B
B
B
Drain: 1" NPT
Drain: 1" NPT
Side/Side connection
NPT/Socket weld
Side/Bottom connection
ANSI RF Flange
Side/Side connection
ANSI RF Flange
Sealed cages
3/4" NPT body cage connection
Select Eclipse GWR probes with 3/4" NPT process connection
Measuring
range
P
Measuring
range
P
Measuring
range
P
(Probe
insertion
length)
(Probe
insertion
length)
(Probe
insertion
length)
E
E
E
D
D
D
B
B
Drain: 1" NPT
Side/Side connection
NPT/Socket weld
6
B
Side/Bottom connection
ANSI RF Flange
Drain: 1" NPT
Side/Side connection
ANSI RF Flange
SEALED AND FLANGED 3" EXTERNAL CAGES
D I M E N S I O N A L S P E C I F I C AT I O N S I N M M ( I N C H E S )
Size
Side-side
Side-bottom
Side-side
Side-bottom
Side-Side
Side-Bottom
Side-Side
Side-Bottom
Connection
Sealed 3" external cage
Flanged 3" external cage
B
E
D
P (Range +)
B
E
D
P (Range +)
1"
NPT - 150/300/600 lbs
69 (2.72)
178 (7.00)
200 (7.87)
314 (12.36)
69 (2.72)
150 (5.91)
200 (7.87)
300 (11.81)
1 1/2"
NPT - 150/300/600 lbs
81 (3.19)
178 (7.00)
200 (7.87)
314 (12.36)
81 (3.19)
150 (5.91)
200 (7.87)
300 (11.81)
2"
NPT - 150/300/600 lbs
84 (3.31)
178 (7.00)
200 (7.87)
314 (12.36)
84 (3.31)
150 (5.91)
200 (7.87)
300 (11.81)
1"
SW - 150/300/600 lbs
69 (2.72)
178 (7.00)
200 (7.87)
314 (12.36)
69 (2.72)
150 (5.91)
200 (7.87)
300 (11.81)
1 1/2"
SW - 150/300/600 lbs
81 (3.19)
178 (7.00)
200 (7.87)
314 (12.36)
81 (3.19)
150 (5.91)
200 (7.87)
300 (11.81)
2"
SW - 150/300/600 lbs
84 (3.31)
178 (7.00)
200 (7.87)
314 (12.36)
84 (3.31)
150 (5.91)
200 (7.87)
300 (11.81)
1"
RF Slip on flange - 150/300/600 lbs
170 (6.69)
178 (7.00)
200 (7.87)
314 (12.36)
170 (6.69)
150 (5.91)
200 (7.87)
300 (11.81)
1 1/2"
RF Slip on flange - 150/300/600 lbs
180 (7.09)
178 (7.00)
200 (7.87)
314 (12.36)
180 (7.09)
150 (5.91)
200 (7.87)
300 (11.81)
2"
RF Slip on flange - 150/300/600 lbs
185 (7.28)
178 (7.00)
200 (7.87)
314 (12.36)
185 (7.28)
150 (5.91)
200 (7.87)
300 (11.81)
1"
RF Slip on flange - 150/300/600 lbs
170 (6.69)
178 (7.00)
325 (12.80)
314 (12.36)
170 (6.69)
150 (5.91)
325 (12.80)
300 (11.81)
1 1/2"
RF Slip on flange - 150/300/600 lbs
180 (7.09)
178 (7.00)
335 (13.19)
314 (12.36)
180 (7.09)
150 (5.91)
335 (13.19)
300 (11.81)
2"
RF Slip on flange - 150/300/600 lbs
185 (7.28)
178 (7.00)
340 (13.39)
314 (12.36)
185 (7.28)
150 (5.91)
340 (13.39)
300 (11.81)
1"
RJ Weld Neck flange - 600 lbs
170 (6.69)
178 (7.00)
200 (7.87)
314 (12.36)
170 (6.69)
150 (5.91)
200 (7.87)
300 (11.81)
1 1/2"
RJ Weld Neck flange - 600 lbs
180 (7.09)
178 (7.00)
200 (7.87)
314 (12.36)
180 (7.09)
150 (5.91)
200 (7.87)
300 (11.81)
2"
RJ Weld Neck flange - 600 lbs
185 (7.28)
178 (7.00)
200 (7.87)
314 (12.36)
185 (7.28)
150 (5.91)
200 (7.87)
300 (11.81)
1"
RJ Weld Neck flange - 900 lbs
181 (7.13)
178 (7.00)
200 (7.87)
314 (12.36)
181 (7.13)
190 (7.48)
200 (7.87)
345 (13.58)
1 1/2"
RJ Weld Neck flange - 900 lbs
193 (7.60)
178 (7.00)
200 (7.87)
314 (12.36)
193 (7.60)
190 (7.48)
200 (7.87)
345 (13.58)
2"
RJ Weld Neck flange - 900 lbs
214 (8.43)
178 (7.00)
200 (7.87)
314 (12.36)
214 (8.43)
190 (7.48)
200 (7.87)
345 (13.58)
1"
RJ Weld Neck flange - 1500 lbs
181 (7.13)
178 (7.00)
200 (7.87)
314 (12.36)
181 (7.13)
205 (8.07)
200 (7.87)
360 (14.17)
1 1/2"
RJ Weld Neck flange - 1500 lbs
193 (7.60)
178 (7.00)
200 (7.87)
314 (12.36)
193 (7.60)
205 (8.07)
200 (7.87)
360 (14.17)
2"
RJ Weld Neck flange - 1500 lbs
214 (8.43)
178 (7.00)
200 (7.87)
314 (12.36)
214 (8.43)
205 (8.07)
200 (7.87)
360 (14.17)
1"
RJ Weld Neck flange - 2500 lbs
197 (7.76)
178 (7.00)
200 (7.87)
314 (12.36)
197 (7.76)
257 (10.12)
200 (7.87)
417 (16.42)
1 1/2"
RJ Weld Neck flange - 2500 lbs
223 (8.78)
178 (7.00)
200 (7.87)
314 (12.36)
223 (8.78)
257 (10.12)
200 (7.87)
417 (16.42)
2"
RJ Weld Neck flange - 2500 lbs
239 (9.41)
178 (7.00)
200 (7.87)
314 (12.36)
239 (9.41)
257 (10.12)
200 (7.87)
417 (16.42)
1"
RJ Weld Neck flange - 600 lbs
170 (6.69)
178 (7.00)
325 (12.80)
314 (12.36)
170 (6.69)
150 (5.91)
325 (12.80)
300 (11.81)
1 1/2"
RJ Weld Neck flange - 600 lbs
180 (7.09)
178 (7.00)
335 (13.19)
314 (12.36)
180 (7.09)
150 (5.91)
335 (13.19)
300 (11.81)
2"
RJ Weld Neck flange - 600 lbs
185 (7.28)
178 (7.00)
340 (13.39)
314 (12.36)
185 (7.28)
150 (5.91)
340 (13.39)
300 (11.81)
1"
RJ Weld Neck flange - 900 lbs
181 (7.13)
178 (7.00)
335 (13.19)
314 (12.36)
181 (7.13)
190 (7.48)
335 (13.19)
345 (13.58)
1 1/2"
RJ Weld Neck flange - 900 lbs
193 (7.60)
178 (7.00)
350 (13.78)
314 (12.36)
193 (7.60)
190 (7.48)
350 (13.78)
345 (13.58)
2"
RJ Weld Neck flange - 900 lbs
214 (8.43)
178 (7.00)
370 (14.57)
314 (12.36)
214 (8.43)
190 (7.48)
370 (14.57)
345 (13.58)
1"
RJ Weld Neck flange - 1500 lbs
181 (7.13)
178 (7.00)
335 (13.19)
314 (12.36)
181 (7.13)
205 (8.07)
335 (13.19)
360 (14.17)
1 1/2"
RJ Weld Neck flange - 1500 lbs
193 (7.60)
178 (7.00)
350 (13.78)
314 (12.36)
193 (7.60)
205 (8.07)
350 (13.78)
360 (14.17)
2"
RJ Weld Neck flange - 1500 lbs
214 (8.43)
178 (7.00)
370 (14.57)
314 (12.36)
214 (8.43)
205 (8.07)
370 (14.57)
360 (14.17)
1"
RJ Weld Neck flange - 2500 lbs
197 (7.76)
178 (7.00)
355 (13.98)
314 (12.36)
197 (7.76)
257 (10.12)
355 (13.98)
417 (16.42)
1 1/2"
RJ Weld Neck flange - 2500 lbs
223 (8.78)
178 (7.00)
380 (14.96)
314 (12.36)
223 (8.78)
257 (10.12)
380 (14.96)
417 (16.42)
2"
RJ Weld Neck flange - 2500 lbs
239 (9.41)
178 (7.00)
395 (15.55)
314 (12.36)
239 (9.41)
257 (10.12)
395 (15.55)
417 (16.42)
DN 25
PN 16/25/40 flange EN 1092-1/ B1
170 (6.69)
178 (7.00)
200 (7.87)
314 (12.36)
170 (6.69)
150 (5.91)
200 (7.87)
300 (11.81)
DN 40
PN 16/25/40 flange EN 1092-1/ B1
180 (7.09)
178 (7.00)
200 (7.87)
314 (12.36)
180 (7.09)
150 (5.91)
200 (7.87)
300 (11.81)
DN 50
PN 16 flange EN 1092-1/ B1
185 (7.28)
178 (7.00)
200 (7.87)
314 (12.36)
185 (7.28)
150 (5.91)
200 (7.87)
300 (11.81)
DN 50
DN 25
DN 40
PN 25/40 flange EN 1092-1/ B1
PN 63 flange EN 1092-1/ B2
PN 63 flange EN 1092-1/ B2
188 (7.40)
190 (7.48)
200 (7.87)
178 (7.00)
178 (7.00)
178 (7.00)
200 (7.87)
200 (7.87)
200 (7.87)
314 (12.36)
314 (12.36)
314 (12.36)
188 (7.40)
190 (7.48)
200 (7.87)
150 (5.91)
150 (5.91)
150 (5.91)
200 (7.87)
200 (7.87)
200 (7.87)
300 (11.81)
300 (11.81)
300 (11.81)
DN 50
PN 63 flange EN 1092-1/ B2
202 (7.95)
178 (7.00)
200 (7.87)
314 (12.36)
202 (7.95)
150 (5.91)
200 (7.87)
300 (11.81)
DN 25
PN 100 flange EN 1092-1/ B2
190 (7.48)
178 (7.00)
200 (7.87)
314 (12.36)
190 (7.48)
150 (5.91)
200 (7.87)
300 (11.81)
DN 40
PN 100 flange EN 1092-1/ B2
200 (7.87)
178 (7.00)
200 (7.87)
314 (12.36)
200 (7.87)
150 (5.91)
200 (7.87)
300 (11.81)
DN 50
PN 100 flange EN 1092-1/ B2
208 (8.19)
178 (7.00)
200 (7.87)
314 (12.36)
208 (8.19)
150 (5.91)
200 (7.87)
300 (11.81)
DN 25
PN 160 DIN 2638 Form E
190 (7.48)
178 (7.00)
200 (7.87)
314 (12.36)
190 (7.48)
205 (8.07)
200 (7.87)
355 (13.98)
DN 40
PN 160 DIN 2638 Form E
200 (7.87)
178 (7.00)
200 (7.87)
314 (12.36)
200 (7.87)
205 (8.07)
200 (7.87)
355 (13.98)
DN 50
PN 160 DIN 2638 Form E
215 (8.46)
178 (7.00)
200 (7.87)
314 (12.36)
215 (8.46)
205 (8.07)
200 (7.87)
355 (13.98)
DN 25
PN 250 DIN 2628 Form E
197 (7.76)
178 (7.00)
200 (7.87)
314 (12.36)
197 (7.76)
205 (8.07)
200 (7.87)
355 (13.98)
DN 40
PN 250 DIN 2628 Form E
216 (8.50)
178 (7.00)
200 (7.87)
314 (12.36)
216 (8.50)
205 (8.07)
200 (7.87)
355 (13.98)
DN 50
PN 250 DIN 2628 Form E
225 (8.86)
178 (7.00)
200 (7.87)
314 (12.36)
225 (8.86)
205 (8.07)
200 (7.87)
355 (13.98)
DN 25
PN 320 DIN 2629 Form E
210 (8.27)
178 (7.00)
200 (7.87)
314 (12.36)
210 (8.27)
257 (10.12)
200 (7.87)
412 (16.22)
DN 40
PN 320 DIN 2629 Form E
224 (8.82)
178 (7.00)
200 (7.87)
314 (12.36)
224 (8.82)
257 (10.12)
200 (7.87)
412 (16.22)
DN 50
PN 320 DIN 2629 Form E
240 (9.45)
178 (7.00)
200 (7.87)
314 (12.36)
240 (9.45)
257 (10.12)
200 (7.87)
412 (16.22)
DN 25
PN 16/25/40 flange EN 1092-1/ B1
170 (6.69)
178 (7.00)
325 (12.80)
314 (12.36)
170 (6.69)
150 (5.91)
325 (12.80)
300 (11.81)
DN 40
PN 16/25/40 flange EN 1092-1/ B1
180 (7.09)
178 (7.00)
335 (13.19)
314 (12.36)
180 (7.09)
150 (5.91)
335 (13.19)
300 (11.81)
DN 50
PN 16 flange EN 1092-1/ B1
185 (7.28)
178 (7.00)
340 (13.39)
314 (12.36)
185 (7.28)
150 (5.91)
340 (13.39)
300 (11.81)
DN 50
PN 25/40 flange EN 1092-1/ B1
188 (7.40)
178 (7.00)
345 (13.58)
314 (12.36)
188 (7.40)
150 (5.91)
345 (13.58)
300 (11.81)
DN 25
PN 63 flange EN 1092-1/ B2
190 (7.48)
178 (7.00)
345 (13.58)
314 (12.36)
190 (7.48)
150 (5.91)
345 (13.98)
300 (11.81)
DN 40
PN 63 flange EN 1092-1/ B2
200 (7.87)
178 (7.00)
355 (13.98)
314 (12.36)
200 (7.87)
150 (5.91)
355 (13.19)
300 (11.81)
DN 50
PN 63 flange EN 1092-1/ B2
202 (7.95)
178 (7.00)
360 (14.17)
314 (12.36)
202 (7.95)
150 (5.91)
360 (14.17)
300 (11.81)
DN 25
PN 100 flange EN 1092-1/ B2
190 (7.48)
178 (7.00)
345 (13.58)
314 (12.36)
190 (7.48)
150 (5.91)
345 (13.58)
300 (11.81)
DN 40
PN 100 flange EN 1092-1/ B2
200 (7.87)
178 (7.00)
355 (13.98)
314 (12.36)
200 (7.87)
150 (5.91)
355 (13.98)
300 (11.81)
DN 50
PN 100 flange EN 1092-1/ B2
208 (8.19)
178 (7.00)
365 (14.37)
314 (12.36)
208 (8.19)
150 (5.91)
365 (14.37)
300 (11.81)
DN 25
PN 160 DIN 2638 Form E
190 (7.48)
178 (7.00)
345 (13.58)
314 (12.36)
190 (7.48)
205 (8.07)
345 (13.58)
355 (13.98)
DN 40
PN 160 DIN 2638 Form E
200 (7.87)
178 (7.00)
355 (13.98)
314 (12.36)
200 (7.87)
205 (8.07)
355 (13.98)
355 (13.98)
DN 50
PN 160 DIN 2638 Form E
215 (8.46)
178 (7.00)
370 (14.57)
314 (12.36)
215 (8.46)
205 (8.07)
370 (14.57)
355 (13.98)
DN 25
PN 250 DIN 2628 Form E
197 (7.76)
178 (7.00)
355 (13.98)
314 (12.36)
197 (7.76)
205 (8.07)
355 (13.98)
355 (13.98)
DN 40
PN 250 DIN 2628 Form E
216 (8.50)
178 (7.00)
370 (14.57)
314 (12.36)
216 (8.50)
205 (8.07)
370 (14.57)
355 (13.98)
DN 50
PN 250 DIN 2628 Form E
225 (8.86)
178 (7.00)
380 (14.96)
314 (12.36)
225 (8.86)
205 (8.07)
380 (14.96)
355 (13.98)
DN 25
PN 320 DIN 2629 Form E
210 (8.27)
178 (7.00)
365 (14.37)
314 (12.36)
210 (8.27)
257 (10.12)
365 (14.37)
412 (16.22)
DN 40
PN 320 DIN 2629 Form E
224 (8.82)
178 (7.00)
380 (14.95)
314 (12.36)
224 (8.82)
257 (10.12)
380 (14.95)
412 (16.22)
DN 50
PN 320 DIN 2629 Form E
240 (9.45)
178 (7.00)
395 (15.55)
314 (12.36)
240 (9.45)
257 (10.12)
395 (15.55)
412 (16.22)
Probe length Eclipse = (dimension “P” + measuring range) arounded to the nearest cm value, e.g. 1523 mm 152 cm or 1526 mm = 153 cm
7
P H Y S I C A L S P E C I F I C AT I O N S
Description
Specification
Measuring range
From 300 mm (11.81") to 5700 mm (224")
Carbon steel or
316/316L SST (1.4401/1.4404) with carbon steel zinc plated studs and nuts or
others at request
All cages are designed to meet the European PED (Pressure Equipment Directives)
97/23 EC guidelines
Standard commercial design
NACE construction
Others at request: eg. IBR, ASME - ANSI B31.3
Material of construction
Design
Constructions
Optional Welding tests
“X”-ray (for full penetration butt welds), Magnetic particle (for Carbon steel cages),
Dye penetrant (for all cages)
Process pressure
Max. 345 bar (5000 psi) – depending selected GWR probe
process temperature
Up to +400 °C (+750 °F) – depending selected GWR probe
QUALITY ASSURANCE - ISO 9001:2000
THE QUALITY ASSURANCE SYSTEM IN PLACE AT MAGNETROL GUARANTEES THE HIGHEST LEVEL OF QUALITY DURING THE DESIGN,
THE CONSTRUCTION AND THE SERVICE OF CONTROLS.
OUR QUALITY ASSURANCE SYSTEM IS APPROVED AND CERTIFIED TO ISO 9001:2000 AND OUR TOTAL COMPANY IS COMMITTED TO
PROVIDING FULL CUSTOMER SATISFACTION BOTH IN QUALITY PRODUCTS AND QUALITY SERVICE.
PRODUCT WARRANTY
:2000
ALL MAGNETROL ELECTRONIC AND ULTRASONIC LEVEL CONTROLS ARE WARRANTED FREE OF DEFECTS IN MATERIALS AND WORKMANSHIP FOR ONE FULL YEAR FROM THE DATE OF ORIGINAL FACTORY SHIPMENT. IF RETURNED WITHIN THE WARRANTY PERIOD; AND, UPON FACTORY INSPECTION OF THE CONTROL, THE CAUSE OF THE CLAIM IS DETERMINED TO BE COVERED UNDER THE WARRANTY; THEN, MAGNETROL INTERNATIONAL WILL REPAIR OR
REPLACE THE CONTROL AT NO COST TO THE PURCHASER (OR OWNER) OTHER THAN TRANSPORTATION.
MAGNETROL SHALL NOT BE LIABLE FOR MISAPPLICATION, LABOR CLAIMS, DIRECT OR CONSEQUENTIAL DAMAGE OR EXPENSE ARISING FROM THE INSTALLATION
OR USE OF THE EQUIPMENT. THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED, EXCEPT, SPECIAL WRITTEN WARRANTIES COVERING SOME MAGNETROL
PRODUCTS.
BULLETIN N°:
EFFECTIVE:
SUPERSEDES:
UNDER RESERVE OF MODIFICATIONS
Heikensstraat 6, 9240 Zele, België
Tel. +32 (0)52.45.11.11 • Fax. +32 (0)52.45.09.93 • E-Mail: [email protected]
DEUTSCHLAND
Alte Ziegelei 2-4, D-51491 Overath
Tel. 02204 / 9536-0 • Fax. 02204 / 9536-53 • E-Mail: [email protected]
FRANCE
40 - 42, rue Gabriel Péri, 95130 Le Plessis Bouchard
Tél. 01.34.44.26.10 • Fax. 01.34.44.26.06 • E-Mail: [email protected]
ITALIA
Via Arese 12, I-20159 Milano
Tel. (02) 607.22.98 (R.A.) • Fax. (02) 668.66.52 • E-Mail: [email protected]
UNITED
KINGDOM
Unit 1 Regent Business Centre, Jubilee Road Burgess Hill West Sussex RH 15 9TL
Tel. (01444) 871313 • Fax (01444) 871317 • E-Mail: [email protected]
INDIA
E-22, Anand Niketan, New Delhi - 110 021
Tel. 91 (11) 51661840 • Fax 91 (11) 51661843 • E-Mail: [email protected]
www.magnetrol.com
BENELUX
OUR NEAREST REPRESENTATIVE
BE 57-140.2
SEPTEMBER 2005
January 2005