® AURORA TM Guided Wave Radar Level Transmitter and Magnetic Level Indicator DESCRIPTION FULL REDUNDANCY Aurora combines the operation of a conventional float operated Magnetic level indicator with the leading edge technology of Guided Wave Radar. The result is a true level measurement redundancy in a single 3" or 4" chamber design. The Eclipse Guided Wave Radar is a 2-wire loop powered 24 V DC liquid level transmitter utilizing Time Domain Reflectometry technology (TDR) to perform level measurement independent from media characteristics and process conditions. The AuroraTM is a completely self-contained unit for side mounting to a tank or vessel with threaded or flanged pipe connections. Flag-type indication F E AT U R E S Shuttle-type indication • Complete redundant system whereby the measuring results of the Eclipse can be continuously checked against the level indication of the Magnetic Level Indicator. • Pro-active maintenance can be planned ahead of time based upon the comparison of the measuring results of the two systems. • No calibration required on either measuring system. • 2-wire, intrinsically safe loop powered level transmitter. • HART®, AMS®, Foundation Fieldbus and PACTware communication protocol. • Up to 5,7 m (224") measuring range. • Up to 103 bar (1500 psi) – optional up to 310 bar (4500 psi). • Up to +400 °C (+750 °F) process temperature - non condensing applications. • Up to 155 bar @ +345 °C (2250 psi @ +650 °F) for saturated steam applications. • Suited for SIL 1 and SIL 2 loops (full FMEDA report available for Eclipse transmitter) – optional SIL 2/3. FE T Y I NT SA EGRITY A G E N C Y A P P R O VA L S Approvals ATEX II 3 G EEx nA II T6, non sparking ATEX II 1 G EEx ia IIC T4, intrinsically safe ➀ ATEX II 1/2 G D EEx d[ia] IIC T6, explosion proof Stoomwezen Secondary level safety device for steamdrums TÜV WHG § 19, overfill prevention AIB VLAREM II – 5.17.7 FM/CSA➁ Non Incendive / Intrinsically safe / Explosion proof LRS Lloyds Register of Shipping (marine applications) Russian Authorisation Standards GOST/ GOSGORTECHNADZOR➁ V EL LE Agency ATEX A P P L I C AT I O N S MEDIA: Clean liquids; hydrocarbons to water-based media (dielectric 1.4-100). INTERFACE: Consult factory. VESSELS: Most process or storage vessels up to rated probe temperature and pressure. CONDITIONS: All level measurement and control applications including process conditions exhibiting visible vapors, foam, surface agitation, bubbling or boiling, high fill/empty rates, low level and varying dielectric media. ➀ Fisco ATEX, intrinsically safe for units with Fieldbus Foundation ➁ Consult factory for proper partnumbers Worldwide level and flow solutions P R I N C I P L E O F O P E R AT I O N The coaxial GWR probe is separated from the float by means of a baffle plate. The baffle plate assures the free travel of the float by rising and falling level. The propagation and reflection of high frequency pulses to determine liquid level happens within the coaxial probe and is not impeded by the magnetic field of the magnets mounted inside the float of the indicator. These float magnets couple with the individual flags as level moves up and down within the pipe column. Coaxial GWR probe non-magnetic chamber wall Liquid level Indicating flags Float magnet Float Baffle plate GWR probe Float Top View ELECTRICAL WIRING Power supply GP / intrinsically safe / Explosion proof: min 11 V DC 0% 100 % Standard shielded twisted cable (recommended but not needed when wired as per NAMUR NE 21 for field strengths up to 10 V/m). Galvanic Barrier max 28,6 V DC @ 94 mA for intrinsically safe units max 17,5 V DC @ 380 mA for Foundation Fieldbus units (not needed for GP Dust Ex and Explosion proof models) Hart® key Ex 2 Non Ex OPTIONS Hot Magnetic level indicators can be ordered with several different tracing options to heat the external chamber. Tracing systems require that a special blanket (custom designed to meet the customers specifications) cover the entire chamber and tracing equipment. Cold To facilitate operation where the product is kept cold via chillers, refrigerants and condensers, a frost extension option and low temperature insulation are offered. The frost extension is constructed of durable acrylic plastic and suitable for contact with media as cold as -200 °C (-320 °F) such as liquid nitrogen. Consult factory for ordering information. S E L E C T I O N D ATA A complete measuring system consists of: 1. Order code for the Aurora - Magnetic Level Indicator 2. Order code for the Aurora - Guided Wave Radar Transmitter 3. Specify separately - operating and min S.G. of the media - max operating pressure and process temperature. 3 1. Order code for the Aurora - Magnetic Level Indicator BASIC MODEL NUMBER Min. S.G. Code B B B B B B B B B B G G G G G G G G G G A B C D E F G H J K 40 °C (100 °F) 27,6 (400) 41,3 (600) 55,2 (800) 41,3 (600) 51,7 (750) 75,8 (1100) 75,8 (1100) 62,0 (900) 103 (1500) 103 (1500) 0,75 0,65 0,50 0,76 0,76 0,65 0,50 0,75 0,65 0,50 Pressure rating in bar (psi) 200 °C 315 °C (400 °F) (600 °F) 26,6 (386) 23,4 (340) 24,3 (352) 18,1 (262) 32,3 (469) 24,1 (349) 39,9 (579) 35,2 (510) 49,9 (723) 43,9 (637) 44,5 (645) 33,1 (480) 44,5 (645) 33,1 (480) 59,9 (868) 52,8 (765) 60,7 (880) 45,2 (655) 60,7 (880) 45,2 (655) 400 °C (750 °F) 22,2 (322) 4,1 (60) 5,5 (80) 33,3 (483) 41,6 (603) 7,6 (110) 7,6 (110) 49,9 (724) 10,3 (150) 10,3 (150) float mat. cage size 316 SST Titanium Titanium 316 SST 316 SST(*) Titanium Titanium 316 SST(*) Titanium(*) Titanium(*) 3" 3" 4" 3" 3" 3" 4" 4" 4" 4" (*) pressurised float MATERIALS OF CONSTRUCTION Code with Code with scale in % scale in cm of span B C E F H J L M Code flags only A D G K Flanges Cage Indication rail Carbon steel 316/316L SST (1.4401/1.4404) Carbon steel 316/316L SST (1.4401/1.4404) 316/316L SST (1.4401/1.4404) Aluminium 316 SST (1.4401) CAGE AND FLANGE RATING A B C D E F 150 lbs 300 lbs 600 lbs 900 lbs 1500 lbs 2500 lbs (max 345 bar (5000 psi)) PROCESS CONNECTION – SIZE 2 1" 3 1 1/2" 4 2" 1 2 3 4 5 6 7 PN PN PN PN PN PN PN B C D 16 25/40 63 100 160 250 320 EN 1092-1 Type B1 EN 1092-1 Type B1 EN 1092-1 Type B2 EN 1092-1 Type B2 DIN 2638 Form E DIN 2628 Form E DIN 2629 Form E DN 25 DN 40 DN 50 DIN sizes only in combination with flanged process conn. PROCESS CONNECTION - TYPE A B D F 1 Threaded NPT-F Socket weld ANSI RF Slip on flanges up to 600 lbs rating ANSI RJ Weld Neck flanges for 600 lbs up to 2500 lbs rating EN/DIN Weld Neck flanges MEASURING RANGE (center-to-center) English ranges (dimensions as per specified inch dimension) 0 0 0 0 0 0 0 0 0 0 A B C D E 14" 32" 48" 60" 72" / / / / / 356 813 1219 1524 1829 mm mm mm mm mm 0 0 0 0 0 0 0 0 F G H I 84" 96" 108" 120" / / / / 2134 2438 2743 3048 mm mm mm mm Metric ranges (specify per cm increments) 0 3 0 4 1 0 5 7 0 B G 4 minimum 30 cm (11.81") maximum 410 cm (161") - for 7MS maximum 570 cm (224") - for 7MD/7MR complete order code for the Aurora - Magnetic Level Indicator Dimensions in mm (inches) 1/2" NPT plugged vent 1/2" NPT plugged vent E E Measuring range Measuring range 254 (10)➀ 1/2" NPT plugged drain 1/2" B Flanged ➀ 254 (10)➀ NPT plugged drain B Threaded/Welded For S.G. < 0.8 and/or flange rating > 1500 lbs / PN 250, dimension will increase Flanged 3" cages Size Connection B E 1" NPT/SW - 150/300 lbs 69 (2.72) 178 (7.00) 1" 1/2" NPT/SW - 150/300 lbs 81 (3.19) 178 (7.00) 2" NPT/SW - 150/300 lbs 84 (3.31) 178 (7.00) 1" RF Slip on flange - 150/300 lbs 170 (6.69) 178 (7.00) 1" 1/2" RF Slip on flange - 150/300 lbs 180 (7.09) 178 (7.00) 2" RF Slip on flange - 150/300 lbs 185 (7.28) 178 (7.00) DN 25 PN 16/25/40 flange EN 1092-1 Type B1 170 (6.69) 178 (7.00) DN 40 PN 16/25/40 flange EN 1092-1 Type B1 180 (7.09) 178 (7.00) DN 50 PN 16 flange EN 1092-1 Type B1 185 (7.28) 178 (7.00) DN 50 PN 25/40 flange EN 1092-1 Type B1 188 (7.40) 178 (7.00) 5 Flanged 4" cages Size Connection B E 1" NPT/SW - 150/300/600 lbs 82 (3.23) 178 (7.00) 1" 1/2" NPT/SW - 150/300/600 lbs 94 (3.70) 178 (7.00) 2" NPT/SW - 150/300/600 lbs 97 (3.82) 178 (7.00) 1" NPT - 900/1500 lbs 92 (3.62) 205 (8.07) 1" 1/2" NPT - 900/1500 lbs 94 (3.70) 215 (8.46) 2" NPT - 900/1500 lbs 97 (3.82) 225 (8.86) 1" NPT - 2500 lbs 99 (3.90) 275 (10.83) 1" 1/2" NPT - 2500 lbs 102 (4.02) 285 (11.22) 2" NPT - 2500 lbs 112 (4.41) 295 (11.61) 1" SW - 900/1500 lbs 99 (3.90) 205 (8.07) 1" 1/2" SW - 900/1500 lbs 102 (4.02) 215 (8.46) 2" SW - 900/1500 lbs 112 (4.41) 225 (8.86) 1" SW - 2500 lbs 99 (3.90) 275 (10.83) 1" 1/2" SW - 2500 lbs 102 (4.02) 285 (11.22) 2" SW - 2500 lbs 112 (4.41) 295 (11.61) 1" RF Slip on flange - 150/300/600 lbs 185 (7.28) 178 (7.00) 1" 1/2" RF Slip on flange - 150/300/600 lbs 200 (7.87) 178 (7.00) 2" RF Slip on flange - 150/300/600 lbs 200 (7.87) 178 (7.00) 1" RJ Weld Neck flange - 600 lbs 185 (7.28) 178 (7.00) 1" 1/2" RJ Weld Neck flange - 600 lbs 200 (7.87) 178 (7.00) 2" RJ Weld Neck flange - 600 lbs 200 (7.87) 178 (7.00) 1" RJ Weld Neck flange - 900 lbs 195 (7.68) 190 (7.48) 1" 1/2" RJ Weld Neck flange - 900 lbs 205 (8.07) 190 (7.48) 2" RJ Weld Neck flange - 900 lbs 225 (8.86) 190 (7.48) 1" RJ Weld Neck flange - 1500 lbs 195 (7.68) 205 (8.07) 1" 1/2" RJ Weld Neck flange - 1500 lbs 205 (8.07) 205 (8.07) 2" RJ Weld Neck flange - 1500 lbs 225 (8.86) 205 (8.07) 1" RJ Weld Neck flange - 2500 lbs 211 (8.31) 275 (10.83) 1" 1/2" RJ Weld Neck flange - 2500 lbs 235 (9.25) 275 (10.83) 2" RJ Weld Neck flange - 2500 lbs 250 (9.84) 275 (10.83) DN 25 PN 16/25/40 flange EN 1092-1 Type B1 185 (7.28) 178 (7.00) DN 40 PN 16/25/40 flange EN 1092-1 Type B1 200 (7.87) 178 (7.00) DN 50 PN 16 flange EN 1092-1 Type B1 200 (7.87) 178 (7.00) DN 50 PN 25/40 flange EN 1092-1 Type B1 203 (7.99) 178 (7.00) DN 25 PN 63 flange EN 1092-1 Type B2 203 (7.99) 178 (7.00) DN 40 PN 63 flange EN 1092-1 Type B2 217 (8.54) 178 (7.00) DN 50 PN 63 flange EN 1092-1 Type B2 217 (8.54) 178 (7.00) DN 25 PN 100 flange EN 1092-1 Type B2 203 (7.99) 178 (7.00) DN 40 PN 100 flange EN 1092-1 Type B2 217 (8.54) 178 (7.00) DN 50 PN 100 flange EN 1092-1 Type B2 223 (8.78) 178 (7.00) DN 25 PN 160 DIN 2638 Form E 205 (8.07) 205 (8.07) DN 40 PN 160 DIN 2638 Form E 219 (8.62) 205 (8.07) DN 50 PN 160 DIN 2638 Form E 230 (9.06) 205 (8.07) DN 25 PN 250 DIN 2628 Form E 212 (8.35) 205 (8.07) DN 40 PN 250 DIN 2628 Form E 235 (9.25) 205 (8.07) DN 50 PN 250 DIN 2628 Form E 240 (9.45) 205 (8.07) DN 25 PN 320 DIN 2629 Form E 225 (8.86) 275 (10.83) DN 40 PN 320 DIN 2629 Form E 243 (9.57) 275 (10.83) DN 50 PN 320 DIN 2629 Form E 255 (10.04) 275 (10.83) 6 2. Order code for the Aurora - Eclipse 705 Guided Wave Radar transmitter TRANSMITTER 7 7 7 7 Type ➀ Eclipse - blind transmitter Eclipse - transmitter with digital display and keypad Eclipse - blind transmitter Eclipse - transmitter with digital display and keypad 3 4 5 6 ➀ Signal output 4-20 mA with HART® communication 4-20 mA with HART® communication Foundation Fieldbus® communication Foundation Fieldbus® communication Power 24 V DC 2-wire loop powered Standard electronics: SFF > 85 %. Consult factory for SIL enhanced electronics: SFF > 91 % MOUNTING/CLASSIFICATION (Consult factory for FM/CSA approvals) 1 Integral, General purpose (&IS: FM/CSA) 2 Remote, General purpose (&IS: FM/CSA) A Integral, ATEX II 1 G EEx ia II C T4 - FISCO ATEX, intrinsically safe for units with Fieldbus Foundation B Integral, ATEX II 1 G EEx ia II C T4 - FISCO ATEX, intrinsically safe for units with Fieldbus Foundation C Integral, ATEX II 1/2 G D EEx d[ia] II C T6 D Remote, ATEX II 1/2 G D EEx d[ia] II C T6 Integral, ATEX II 3 G EEx nA II T6 E F Remote, ATEX II 3 G EEx nA II T6 HOUSING 1 Cast aluminium dual compartiment, 3/4" NPT cable entry (2 entries – one plugged) 2 Cast aluminium dual compartiment, M20 x 1,5 cable entry (2 entries – one plugged) 3 Stainless steel dual compartiment, 3/4" NPT cable entry (2 entries – one plugged) 4 Stainless steel dual compartiment, M20 x 1,5 cable entry (2 entries – one plugged) PROBE TYPE - all coaxial type, overfill safe GWR probes R 7MR - Overfill safe GWR probe D 7MD - High Temp / High Pressure (HTHP) GWR probe S 7MS - Saturated steam GWR probe (dielectric range ≥ 1,4) - WHG approved (dielectric range ≥ 2,0) - WHG approved (dielectric range ≥ 10,0) - Stoomwezen approved PROBE MATERIAL A 316 / 316 L (1.4401/1.4404) stainless steel B Hastelloy C (2.4819) not for “S” probe (7MS) C Monel (2.4360) not for “S” probe (7MS) PROCESS SEAL-MATERIAL ➀ For the 7MR GWR probe ➁ 0 1 2 Viton® GFLT - for universal use / steam applications min -40°C (-40 °F) / max +200 °C (+400 °F) EPDM (Ethylene Propylene) - for e.g. caustic soda applications min -50°C (-60 °F) / max +125 °C (+250 °F) min -40°C (-40 °F) / max +200 °C (+400 °F) Kalrez 4079 - for aggressive media ➀ Consult factory for alternative seal materials ➁ For ammonia/chlorine applications use the 7MD GWR probe. For the 7MD GWR probe N Borosilicate - for non condensing applications min -195 °C (-320 °F) / max +400 °C (+750 °F) For the 7MS GWR probe 8 PEEK - for saturated steam applications min -40 °C (-40 °F) / max +345 °C (+650 °F) MEASURING RANGE (Select the same measuring range as per page 4) English ranges (dimensions as per specified inch dimension) 84" / 2134 0 0 F 0 0 A 14" / 356 mm G 96" / 2438 0 0 0 0 B 32" / 813 mm 0 0 H 108" / 2743 0 0 C 48" / 1219 mm 0 0 I 120" / 3048 0 0 D 60" / 1524 mm 0 0 E mm mm mm mm 72" / 1829 mm Metric ranges (specify per cm increments) 0 3 0 4 1 0 5 7 0 7 minimum 30 cm (11.81") maximum 410 cm (161") - for 7MS maximum 570 cm (224") - for 7MD/7MR complete order code for the Aurora - Eclipse 705 Guided Wave Radar transmitter Viton® is a registered trademark of Dupont Performance Elastomers 7 ECLIPSE 705 TRANSMITTER Dimensions in mm (inches) 83 (3.28) 105 (4.12) 83 (3.28) 105 (4.12) 102 (4.00) 102 (4.00) 256 (10.08) 256 (10.08) 45° 45° 2 cable entries 2 cable entries 168 (6.61) Mounting Flange 7MD: 277 (10.90) 7MS: 240 ( 9.45) Mounting Flange Probe Insertion Length Probe Insertion Length 7MD/7MS with flanged connection 7MR with flanged connection 83 (3.28) 105 (4.12) 45° View 102 (4.00) 70 (2.75) 2 cable entries 76 (3.00) 51 (2.00) 89 (3.50) 95 (3.75) 45° 214 (8.43) 840 (33.00) 2 holes 126 (4.94) 108 (4.25) Remote Eclipse housing 111 (4.38) Eclipse Housing, (45° View) 8 T R A N S M I T T E R S P E C I F I C AT I O N S FUNCTIONAL/PHYSICAL Description Power (at terminals) Specification General Purpose / ATEX Intrinsically Safe: 11 to 28,6 V DC ATEX Explosion Proof (with Intrinsically Safe probe) 11 to 36 V DC Foundation Fieldbus (FISCO ATEX Exi): 9 to 17,5 V DC Foundation Fieldbus (General purpose & Exd): 9 to 32 V DC 4-20 mA with HART®, 3,8 mA to 20,5 mA useable (meets NAMUR NE 43) or Foundation Fieldbus H1 (ITK Ver. 4) Signal Output Span 300 to 5700 mm (12 to 224") (7MS: max 4100 mm (161")) Resolution Analog: 0,01 mA Display: 0,1 cm (inch) 630 Ω @ 20,5 mA - 24 V DC Loop Resistance Damping Diagnostic Alarm User Interface Display Menu Language Housing Material Approvals SIL (Safety Integrity Level) Adjustable 0-10 s Adjustable 3,6 mA, 22 mA, HOLD 3-button keypad and/or HART® communicator, Foundation Fieldbus, AMS® or PACTware® 2-line x 8-character LCD English/Spanish/French/German IP 66/Aluminium A356T6 (< 0.20 % copper) or stainless steel ATEX II 1 G EEx ia II C T4, intrinsically safe – for non Foundation Fieldbus units FISCO ATEX, intrinsically safe - for Foundation Fieldbus units ATEX II 1/2 G D EEx d[ia] II C T6 - T85 °C, explosion proof for all units➀ ATEX II 3 G EEx nA II T6, non sparking – for non Foundation Fieldbus units FM and CSA, Non incendive, intrinsically safe (FISCO) and explosion proof STOOMWEZEN – Secondary level safety device for steamdrums TÜV – WHG § 19, VLAREM II 5.17-7 LRS – Lloyds Register of Shipping (marine applications) GOST-K/GGTN-K – ROSTECH/FSTS – Russian Authorisation Standards Standard electronics Enhanced electronics Functional safety to SIL 1 / SIL 2 in accordance to 61508 – SFF > 85 % – full FMEDA reports and declaration sheets available at request Functional safety to SIL 2 / SIL 3 in accordance to 61508 – SFF > 91 % – full FMEDA reports and declaration sheets available at request Ui = 28,4 V, li = 94 mA, Pi = 1 W Ui = 17,5 V, li = 380 mA, Pi = 5,32 W (Foundation Fieldbus) Ci = 2,2 nF, Li = 3 µH Ci = 0,24 nF, Li = 3 µH (Foundation Fieldbus) ANSI/ISA-571.03 SA1 (Shock), ANSI/ISA-571.03 VC2 (Vibration) 2,70 kg net; 3,20 kg gross – amplifier only 5,70 kg net; 6,20 kg gross – amplifier only H 214 mm (8.43") x W 111 mm (4.38") x D 188 m Electrical Data Equivalent Data Shock/Vibration Class Net and Gross Weight Cast aluminium Stainless steel Overall Dimensions ➀ ATEX, explosion proof units use EEx d bushing material STYCAST 2057 FR PERFORMANCE Description Specification Reference Conditions with a 1,8 m (72") coaxial type GWR probe Coaxial/twin lead probes Linearity➁ Single lead probes ➁ Coaxial/twin lead probes Accuracy Single lead probes 7MT interface Resolution Repeatability Hysteresis Response Time Warm-up Time Ambient Temp. Reflection from liquid, with dielectric in center of selected range, at +20 °C (70 °F) with CFD threshold➀ Process Dielectric Effect Operating Temp. Effect Humidity Electromagnetic Compatibility < 0,1 % of probe length or 2,5 mm (0.1"), whichever is greater < 0,3 % of probe length or 8 mm (0.3"), whichever is greater < 0,1 % of probe length or 2,5 mm (0.1"), whichever is greater ± 0,5 % of probe length or 13 mm (0.5"), whichever is greater ± 25 mm (1") ± 2,5 mm (0.1") < 2,5 mm (0.1") < 2,5 mm (0.1") < 1 second < 5 seconds -40 °C to +80 °C (-40 °F to +175 °F) – blind transmitter -20 °C to +70 °C (-5 °F to +160 °F) – with digital display -40 °C to +70 °C (-40 °F to +160 °F) – for EEx ia and EEx d[ia] with blind transmitter -20 °C to +70 °C (-5 °F to +160 °F) – for EEx ia and EEx d[ia] with digital display < 7,5 mm (0.3") within selected range Approx. +0,02 % of probe length/°C for probes ≥ 2,5 m (8')➂ 0-99 %, non-condensing Meets CE requirements (EN-61000-6-4, EN 61000-6-2) and NAMUR NE 21 (Single and Twin-Rod probe must be used in metallic vessel or stillwell) ➀ May degrade for 7MD probe or with fixed threshold. ➁ Top 600 mm (24") of twin rod probe: 30 mm (1.18"). ➂ Accuracy may degrade slightly < 2,5 m (8') Top 1220 mm (48") of single rod: application dependant. 9 P R O B E S P E C I F I C AT I O N S Description Materials Probe Process seal Probe diameter Mounting Process Connection Probe length Transition Zone➀ Top Bottom Max. Process Temp. Max. Process Pressure Dielectric Range – Max. Viscosity 7MR: overfill safe GWR probe 316/316L (1.4401/1.4404) Hastelloy C® (2.4819) or Monel® (2.4360) Viton® GFLT, EPDM or Kalrez 4079 (Consult factory for alternatives) Inside rod: 8 mm (0.3125") – Outer tube: 22 mm (0.875") In-tank mounting / external cage mounting (WHG approved) Threaded: 3/4" NPT or 1" BSP (G1) Flanged: Various ANSI, EN/DIN or torque tube mating flanges From 600 mm to 6100 mm (24 to 240"), selectable per 10 mm 0 mm (0") εr: 2,0 = 150 mm (6")/εr: 80 = 25 mm (1") +200 °C @ 18 bar (+400 °F @ 270 psi) 70 bar @ +20 °C (1000 psi @ +70 °F) – see table at page 11 1,4 to 100 – 200 cP Viton® is a registered trademark of Dupont Performance Elastomers Description Materials Probe Process seal Spacers Probe diameter Mounting Process Connection Probe length (selectable per 10 mm) Top Transition Zone➀ Bottom Process Temp. Max. Process Pressure Max. Viscosity Dielectric Range Vacuum service 10 Max Min 7MD: high pressure/high temperature 7MS: saturated steam GWR probe GWR probe (overfill safe) (overfill safe) 316/316L (1.4401/1.4404) Borosilicate/inconel X750 PEEK with Aegis PF 128 Ceramic Inside rod: 8 mm (0.125") – Outer tube: 22 mm (0.875") In-tank mounting / external cage mounting (7MD – WHG / 7MS – Stoomwezen approved) Threaded: 3/4" NPT or 1" BSP (G1) Flanged: Various ANSI, EN/DIN or “proprietary” mating flanges From 600 mm to 6100 mm (24 to 240") From 1100 mm to 4500 mm (43 to 177") 25 mm (1") εr: 2,0 = 150 mm (6") / εr: 80 = 25 mm (1") εr: 10 = 150 mm (6") / εr: 80 = 25 mm (1") +400 °C @ 135 bar (+750 °F @ 2000 psi) -196 °C @ 135 bar (-320 °F @ 2000 psi) 345 bar @ +20 °C (5000 psig @ +70 °F) 200 cP 2 to 100 Full vacuum (Helium leak < 10-8 cc/s @ 1 atmosphere vacuum) +345 °C @ 155 bar (+650 °F @ 2250 psi) -15 °C @ 205 bar (0 °F @ 3000 psi) 155 bar @ +345 °C (2250 psi @ +650 °F) 10 to 100 Negative pressure but not up to full vacuum M A G N E T I C L E V E L I N D I C AT O R – S P E C I F I C AT I O N S Measured value Measuring range Liquid level (consult factory for liquid-liquid interface) From 300 mm (11.81") up to 5700 mm (224") Indicators Metal flag (red/white) – all indicators are hermetically sealed and assured by the “Insta-Seal” technology Scale Specific gravity Visual indication Type Materials Materials Size Rating Configuration Float Cage Insulation material Process connections Design Constructions In cm or % of span As low as 0.5 kg/dm3 Visible from a distance up to 30 m (100 feet) With magnetic flux ring – assembly – see page 2 316 SST (1.4401), Titanium, others at request 316/316L SST (1.4401/1.4404), others at request 3" or 4" depending configuration Up to 2500 lbs / PN 320 class ratings Side/side connection with 1/2" NPT plugged vent and drain Weather resistant silicone cloth (high temperature application) Polyurethane + aluminium jacket with polymeric frost extension for flag-rail (cryogenic application) Threaded, socket welded or flanged All cages are designed to meet the European PED (Pressure Equipment Directives) 97/23 EC guidelines Standard commercial design NACE construction Others at request: eg. IBR, ASME - ANSI B31.3 T E M P E R AT U R E - P R E S S U R E R AT I N G F O R E C L I P S E P R O B E S E A L S 350 60 Process Pressure (bar) Process Pressure (bar) 70 50 40 30 20 10 300 250 200 150 100 50 0 0 -40 -20 0 20 40 60 80 100 120 140 160 180 Process Temperature (°C) 7MR: overfill prevention GWR probe 200 -150 -100 -50 0 50 100 150 200 250 300 350 400 Process Temperature (°C) 7MD: high temperature / high pressure GWR probe 7MS: saturated steam GWR probe 11 QUALITY ASSURANCE - ISO 9001:2000 THE QUALITY ASSURANCE SYSTEM IN PLACE AT MAGNETROL GUARANTEES THE HIGHEST LEVEL OF QUALITY DURING THE DESIGN, THE CONSTRUCTION AND THE SERVICE OF CONTROLS. OUR QUALITY ASSURANCE SYSTEM IS APPROVED AND CERTIFIED TO ISO 9001:2000 AND OUR TOTAL COMPANY IS COMMITTED TO PROVIDING FULL CUSTOMER SATISFACTION BOTH IN QUALITY PRODUCTS AND QUALITY SERVICE. PRODUCT WARRANTY :2000 ALL MAGNETROL MECHANICAL LEVEL CONTROLS ARE WARRANTED FREE OF DEFECTS IN MATERIALS AND WORKMANSHIP FOR FIVE FULL YEARS (ELECTRONICS ONE FULL YEAR) FROM THE DATE OF ORIGINAL FACTORY SHIPMENT. IF RETURNED WITHIN THE WARRANTY PERIOD; AND, UPON FACTORY INSPECTION OF THE CONTROL, THE CAUSE OF THE CLAIM IS DETERMINED TO BE COVERED UNDER THE WARRANTY; THEN, MAGNETROL INTERNATIONAL WILL REPAIR OR REPLACE THE CONTROL AT NO COST TO THE PURCHASER (OR OWNER) OTHER THAN TRANSPORTATION. MAGNETROL SHALL NOT BE LIABLE FOR MISAPPLICATION, LABOR CLAIMS, DIRECT OR CONSEQUENTIAL DAMAGE OR EXPENSE ARISING FROM THE INSTALLATION OR USE OF THE EQUIPMENT. THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED, EXCEPT, SPECIAL WRITTEN WARRANTIES COVERING SOME MAGNETROL PRODUCTS. BULLETIN N°: EFFECTIVE: SUPERSEDES: UNDER RESERVE OF MODIFICATIONS Heikensstraat 6, 9240 Zele, België Tel. +32 (0)52.45.11.11 • Fax. +32 (0)52.45.09.93 • E-Mail: [email protected] DEUTSCHLAND Alte Ziegelei 2-4, D-51491 Overath Tel. 02204 / 9536-0 • Fax. 02204 / 9536-53 • E-Mail: [email protected] FRANCE 40 - 42, rue Gabriel Péri, 95130 Le Plessis Bouchard Tél. 01.34.44.26.10 • Fax. 01.34.44.26.06 • E-Mail: [email protected] ITALIA Via Arese 12, I-20159 Milano Tel. (02) 607.22.98 (R.A.) • Fax. (02) 668.66.52 • E-Mail: [email protected] UNITED KINGDOM Unit 1 Regent Business Centre, Jubilee Road Burgess Hill West Sussex RH 15 9TL Tel. (01444) 871313 • Fax (01444) 871317 • E-Mail: [email protected] INDIA E-22, Anand Niketan, New Delhi - 110 021 Tel. 91 (11) 41661840 • Fax 91 (11) 41661843 • E-Mail: [email protected] www.magnetrol.com BENELUX OUR NEAREST REPRESENTATIVE BE 57-138.3 NOVEMBER 2005 December 2002