Multi-rate OC-12/STM-4 SFP Transceivers with Digital Diagnostics TRPA12M SM Product Description The TRPA12M SFP series of multi-rate fiber optic transceivers with integrated digital diagnostics monitoring functionality provide a quick and reliable interface for OC-12 short reach (SR), intermediate reach (IR) and long reach (LR) applications. The diagnostic functions, alarm and warning features as described in the Multi-Source Agreement (MSA) document, SFF-8472 (Rev. 9.3), are provided via an I2C serial interface. Available products under this series are compliant with SONET/SDH standards for OC-12/STM-4 applications and are capable of operating down to 155Mb/s data rate. The SR-1 and IR-1 versions are compliant with OC-12/ STM-4 and OC-3/STM-1 interface standards. All modules satisfy Class I Laser Safety requirements in accordance with the U.S. and international standards as described in the FDA/CDRH and IEC-60825 documents, respectively. The TRPA12M multi-rate transceivers connect to standard 20-pad SFP connectors for hot plug capability. This allows the system designer to make configuration changes or maintenance by simply plugging in different types of transceivers without shutting down the power supply of the host system. The transceivers have colored bail-type latches, which offer an easy and convenient way to release the modules. The latch is compliant with the SFP MSA. Features Compliant with SONET/SDH OC-12/STM-4 (622Mb/s) Compatible with SONET/SDH OC-3/STM-1 (155Mb/s) Compatible with SFP MSA SONET/SDH Reaches (SR-1, IR-1, LR-1 & LR-2) Digital Diagnostics through Serial Interface The transmitter design incorporates a highly reliable 1310nm or 1550nm InGaAsP laser and an integrated driver circuit. The receiver features a transimpedance amplifier IC optimized for high sensitivity and wide dynamic range. The transmitter and receiver DATA interfaces are AC-coupled internally. LVTTL Transmitter Disable control input and Loss of Signal output interfaces are also provided. Internal Calibration for Digital Diagnostics The transceivers operate from a single +3.3V power supply over two operating case temperature ranges of -5°C to +70°C and -40°C to +85°C. Hot-pluggable Eye Safe (Class I Laser Safety) Duplex LC Optical Interface -40°C to +85°C Operating Temperature Option Excellent EMI & ESD Protection TX Fault & Loss of Signal Outputs TX Disable Input Single +3.3V Power Supply Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature 1 “B” option “A” option Symbol Minimum Maximum Units Tst - 40 + 85 °C -5 + 70 - 40 + 85 Top °C Supply Voltage Vcc 0 + 5.0 V Input Voltage Vin 0 + 5.0 V 1 Measured on top side of SFP module at the front center vent hole of the cage. An Oplink Company RevC-P.2009.04.01 TRPA12M Single Mode Multi-rate Transmitter Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Operating Data Rate Average Optical Output Power (coupled into single mode fiber), 50% duty cycle SR-1 & IR-1 LR-1 & LR-2 Symbol Minimum Typical Maximum Units B 125 - 622 Mb/s - 15.0 - 11.0 - 8.0 - 3.0 - 1.0 + 2.0 - - - 45.0 8.2 - - 10 - - 1261 1310 1360 1274 1310 1356 PO POFF Transmitter OFF Output Power SR-1 & IR-1 Extinction Ratio LR-1 & LR-2 Phi /Plo SR-1 Center Wavelength IR-1 1 λC 1293 1310 1334 1280 1310 1335 LR-2 1480 1550 1580 - - 4.0 - - 2.5 or 4.0 ΔλRMS IR-1 dBm dB LR-1 SR-1 Spectral Width (RMS) 1 dBm nm nm Spectral Width (-20dB) LR-1 & LR-2 Δλ20 - - 1.0 nm Side Mode Suppression Ratio LR-1 & LR-2 SMSR 30 - - dB Optical Output Eye 1 Compliant with Telcordia GR-253-CORE and ITU-T Recommendation G.957 For IR version, the center wavelength is either 1274nm ≤ λc ≤ 1356nm for ΔλRMS ≤ 2.5nm or 1293nm ≤ λc ≤ 1334nm for ΔλRMS ≤ 4.0nm Receiver Performance Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Operating Data Rate Receiver Sensitivity (10 BER) -10 1 Minimum Typical Maximum Units B 125 - 622 Mb/s Pmin - 28.0 - 31.0 - dBm dBm Pmax - 7.0 - 3.0 - Increasing Light Input Plos+ - - - 28.0 Decreasing Light Input Plos- - 45.0 - - Maximum Input Optical Power (10 BER) -10 LOS Thresholds 1 Symbol 1 dBm Increasing Light Input t_loss_off - - 100 Decreasing Light Input t_loss_on 2.3 - 100 LOS Hysteresis - 0.5 1.5 - dB Wavelength of Operation λ 1100 - 1600 nm Receiver Reflectance (LR-2) - - - - 27.0 dB LOS Timing Delay 1 µs Specified in average optical input power and measured at 155Mb/s & 622Mb/s and 1310nm wavelength (1550nm for LR-2) with 2 -1 PRBS, and at 125Mb/s with 27-1 PRBS. 23 Laser Safety: All transceivers are Class I Laser products per FDA/CDRH and IEC-60825 standards. They must be operated under specified operating conditions. Oplink Communications, Inc. DATE OF MANUFACTURE: This product complies with 21 CFR 1040.10 and 1040.11 Meets Class I Laser Safety Requirements Oplink Communications, Inc. 2 RevC-P.2009.04.01 TRPA12M Single Mode Multi-rate Transmitter Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Symbol Minimum Input Voltage Swing (TD+ & TD-) 1 VPP-DIF 0.25 Input HIGH Voltage (TX Disable) 2 VIH 2.0 Input LOW Voltage (TX Disable) 2 VIL 0 Output HIGH Voltage (TX Fault) 3 VOH VOL Output LOW Voltage (TX Fault) 3 Typical Maximum Units - 2.4 V - VCC V - 0.8 V 2.0 - VCC + 0.3 V 0 - 0.8 V Differential peak-to-peak voltage. There is an internal 4.7 to 10kΩ pull-up resistor to VccT. 3 Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). 1 2 Receiver Electrical Interface (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Symbol Minimum Typical Maximum Units VPP-DIF 0.6 - 2.0 V VOH 2.0 - VCC + 0.3 V VOL 0 - 0.5 V Output Voltage Swing (RD+ & RD-) 1 Output HIGH Voltage (LOS) 2 Output LOW Voltage (LOS) 2 1 2 Differential peak-to-peak voltage across external 100Ω load. Open collector compatible, 4.7 to 10kΩ pull-up resistor to Vcc (Host Supply Voltage). Electrical Power Supply Characteristics (Over Operating Case Temperature, VCC = 3.13 to 3.47V) Parameter Symbol Minimum Typical Maximum Units Supply Voltage VCC 3.13 3.3 3.47 V Supply Current ICC - 210 275 mA Module Definition MOD_DEF(0) pin 6 MOD_DEF(1) pin 5 MOD_DEF(2) pin 4 Interpretation by Host TTL LOW SCL SDA Serial module definition protocol Electrical Pad Layout 20 TX GND 1 TX GND 19 TD- (TX DATA IN-) 2 TX Fault 18 TD+ (TX DATA IN+) 3 TX Disable 17 TX GND 4 MOD_DEF(2) 16 VccTX 5 MOD_DEF(1) 15 VccRX 6 MOD_DEF(0) 14 RX GND 7 NO CONNECTION 13 RD+ (RX DATA OUT+) 8 LOS 12 RD- (RX DATA OUT-) 9 RX GND 11 RX GND 10 RX GND Top of Board Oplink Communications, Inc. Host Board Connector Pad Layout 1 2 3 Toward Bezel 4 5 6 7 8 9 Bottom of Board (as viewed thru top of board) 10 3 20 19 18 17 16 15 Toward ASIC 14 13 12 11 RevC-P.2009.04.01 TRPA12M Single Mode Multi-rate Example of SFP host board schematic Vcc 3.3V 1µH coil or ferrite bead (<0.2Ω series resistance) Vcc 3.3V + 10 0.1 0.1 + 10 0.1 R 16 2 15 TRPA12M 3 TX Disable 100 50Ω line TX DATA IN+ TX DATA IN- 50Ω line R MOD_DEF(2) MOD_DEF(1) 6 50Ω line 13 19 12 R TX Fault LOS 8 4 5 18 R 50Ω line MOD_DEF(0) (100Ω to ground internally) RX DATA OUT+ to 50Ω load RX DATA OUTto 50Ω load 1, 9, 10, 11, 14, 17, 20 R: 4.7 to 10kΩ Application Notes Electrical Interface: All signal interfaces are compliant with the SFP MSA specification. The high speed DATA interface is differential AC-coupled internally with 0.1μF and can be directly connected to a 3.3V SERDES IC. All low speed control and sense output signals are open collector TTL compatible and should be pulled up with a 4.7 - 10kΩ resistor on the host board. up, MOD_DEF(1:2) appear as NC (no connection), and MOD_DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol (standard two-wire I2C serial interface) and generates the serial clock signal (SCL). The positive edge clocks data into the EEPROM segments of the SFP that are not write protected and the negative edge clocks data from the SFP. Loss of Signal (LOS): The Loss of Signal circuit monitors the level of the incoming optical signal and generates a logic HIGH when an insufficient photocurrent is produced. The serial data signal (SDA) is for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The supported monitoring functions are temperature, voltage, bias current, transmitter power, average receiver signal, all alarms and warnings, and software monitoring of TX Fault/LOS. The device is internally calibrated. TX Fault: The output indicates LOW when the transmitter is operating normally, and HIGH with a laser fault including laser end-of-life. TX Fault is an open collector/drain output and should be pulled up with a 4.7 - 10kΩ resistor on the host board. TX Fault is non-latching (automatically deasserts when fault goes away). The data transfer protocol and the details of the mandatory and vendor specific data structures are defined in the SFP MSA and SFF-8472, Rev. 9.3. TX Disable: When the TX Disable pin is at logic HIGH, the transmitter optical output is disabled (less than -45dBm). Power Supply and Grounding: The power supply line should be well-filtered. All 0.1μF power supply bypass capacitors should be as close to the transceiver module as possible. Serial Identification and Monitoring: The module definition of SFP is indicated by the three module definition pins, MOD_DEF(0), MOD_DEF(1) and MOD_DEF(2). Upon power Oplink Communications, Inc. 4 RevC-P.2009.04.01 TRPA12M Single Mode Multi-rate Package Outline 56.7 2.23 REF 0 1.27 -0.13 .050 +.000 -.005 13.67 13.54 .54 .53 0 0.98 -0.13 +.000 .038 -.005 46335 Landing Pkwy Fremont, CA 94538-6407 Tel: (510) 933-7200 Fax: (510) 933-7300 Email: [email protected] • www.oplink.om 6.25±0.05 .246±.002 1 .04 FRONT EDGE OF TRANSCEIVER CAGE 47.3 1.861 8.9 .350 13.9±0.2 .546±.008 8.51 .335 1.8 .07 41.8±0.15 1.646±.006 45±0.20 1.771±.008 Dimensions in inches [mm] Default tolerances: .xxx = ± .005”, .xx = ± .01” Ordering Information 1 Model Name Operation Temperature Latch Color Nominal Wavelength SONET/SDH Standad Reach 1 TRPA12S1ABAM - 5°C to +70°C Gray 1310nm SR-1/I-4 12/2km TRPA12I1ABYM - 5°C to +70°C Yellow 1310nm IR-1/S-4.1 21/15km TRPA12L1GBRM - 5°C to +70°C Red 1310nm LR-1/L-4.1 42/40km TRPA12L2GBWM - 5°C to +70°C White 1550nm LR-2/L-4.2 85/80km TRPA12S1AAAM 40°C to +85°C Gray 1310nm SR-1/I-4 12/2km TRPA12I1AAYM 40°C to +85°C Yellow 1310nm IR-1/S-4.1 21/15km TRPA12L1GARM 40°C to +85°C Red 1310nm LR-1/L-4.1 42/40km TRPA12L2GCWM 40°C to +85°C White 1550nm LR-2/L-4.2 85/80km These are target distances to be used for classification and not for specification, per Telcordia GR-253-CORE/ITU-T Recommendation G.957. Oplink can provide a remarkable range of customized optical solutions. For detail, please contact Oplink’s Sales and Marketing for your requirements and ordering information (510) 933-7200 or [email protected]. Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Communications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringements of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. RevC-P.2009.04.01 © 2008, Oplink Communications, Inc. 5