WT - Nichicon

ALUMINUM ELECTROLYTIC CAPACITORS
WT
Chip Type, Wide Temperature Range
series
Chip type operating over wide temperature range of to – 55 to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WZ
High
Temperature
Reflow
WF
Low
impeadance
UT
Long Life
WT
Smaller
ZT
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
4 to 50V
Rated Capacitance Range
0.1 to 1500µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz at 20°C
4
0.40
Rated voltage (V)
tan δ (MAX.)
Tangent of loss angle (tan δ)
6.3
0.30
10
0.24
16
0.20
25
0.16
35
0.14
50
0.14
Measurement frequency : 120Hz
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
Stability at Low Temperature
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
The specifications listed at right shall be
met when the capacitors are restored to
20°C after the rated voltage is applied for
1000 hours at 105°C.
Endurance
Resistance to soldering
heat
Marking
Chip Type
(φ3 to φ8 × 5.4 )
25
2
4
35
2
3
50
2
3
Within ±25% of the initial capacitance value for capacitors of φ3mm unit, and 16V or less.
Within ±20% of the initial capacitance value for capacitors of 25V or more.
Capacitance
change
tan δ
200% or less than the initial specified value
Leakage current Less than or equal to the initial specified value
A±0.2
E
B±0.2
φD±0.5
A2P
100
35V
A±0.2
A±0.2
H
Negative
1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated
voltage is omitted.
2. In case of marking for φ3 units. Lot No is expressed by a digit (month code).
Dimension table in next page.
8
2
9 10 11 12 13 14
3
4
5
6
7
8
φD
code
3 to 8 (5.4L)
GB
6.3 to 10 (L 5.8) GS
9 10 11 12 13 14
3
6.3
Package code
Size code
Configuration
φD
3
4 to 10
φD
code
3 to 8 (L 7.7)
CL
Rated capacitance (10µF)
8 to 10 (L tolerance
= 10)
NL(±20%)
Capacitance
Rated voltage (16V)
Capacitance tolerance (±20%)
Series name
Rated capacitance (10µF)
Type
Rated voltage (16V)
Type
φD
Negative
1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated
voltage is omitted.
L±0.5
2.
case of marking for φ3 units. Lot No is expressed by a digit (month code).
LotInNo.
Pressure relief vent
7
A±0.2
0.5 MAX.
C±0.2
H
1
code
2
1
Configuration
φD
3 to 8 (L 7.7)
8 to 10 (L = 10)
code
CL
NL
Series name
L±0.5
Pressure relief vent
6
Positive
A±0.2
B±0.2
1
Voltage
A2P
100
35V
C±0.2
Plastic platform
0.3 MAX.
φD±0.5
Capacitance
Plastic platform
0.3 MAX.
5
Positive
E
1
10Voltage
)
4
E
A±0.2
E
B±0.2
3 Apply to φ6.3 × 5.8, φ6.3 × 7.7
3
Negative
H
3
2
UWT 1 C 1 0 0 MC L 1 G B
Negative
H
3
1
UWT 1 C 1 0 0 MC L 1 G B
0.5 MAX.
(φ8 × 10, φ10 × 10 )
Lot No.
16
2
4
A±0.2
B±0.2
+0.1
–0.2
(L±0.3)
×
0.5 MAX.
φD±0.5
2
105˚C Marking
(φ8 ×mark
10, φ10
Trade
Positive
+0.1
3 Apply to φ6.3 L
× 5.8,
–0.2φ6.3 × 7.7
Capacitance
105˚C Marking
Trade mark
L
C±0.2
A±0.2
0.3 MAX.
(L±0.3)
Lot No.
C±0.2
Voltage
φD±0.5
Lot No.
2
A2P 10
16V
10
16V
A2P
105˚C Marking
Plastic platform
Plastic
platform
0.3 MAX.
1
0.5 MAX.
Positive
1
Voltage
105˚C Marking
10
3
8
Type numbering system (Example : 16V 10µF)
(φ3 to φ8 × 5.4 )
Capacitance
6.3
4
8
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which
Capacitance change Within ±10% of the initial capacitance value
is maintained at 250°C. The capacitors shall meet the
Less than or equal to the initial specified value
tan δ
characteristic requirements listed at right when they are
Less than or equal to the initial specified value
Leakage current
removed from the plate and restored to 20°C.
Black print on the case top.
Shelf Life
Capacitance
4
7
15
×L
3 × 5.4
4 × 5.4
A
1.5
1.8
B
3.3
φD
4.3
C
3.3
4.3
E
0.8
1.0
1.3
2.2
L
5.4
B
5.4
5.43.3
5.4
H
A
5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 5.4
2.1
×L
5.3
3×
2.4
2.4
2.4
3.3
(mm)
8 × 10
10 × 10
2.9
3.2
6.6 6.3 8.3
10.3 × 7.7 8 × 5.4
× 5.4 6.38.3× 5.8 6.3
5.4 6.64 × 5.46.6 5 × 5.4
5.3
1.5
6.6
6.6
1.8
6.6
8.3
2.4
2.4
3.3
5.37.7
6.6
5.4
6.6
10
106.6
8.3
0.5 to 0.8 0.5 to
0.8 0.5 to 0.84.3
0.5 to 0.8 5.3
0.5 to 0.8 0.5
to 0.8 0.8 to
1.1 0.8 to 6.6
1.1
C0.8 0.5 to 3.3
6.6
6.6
8.3
2.2
2.3
2.4
10.3
4.5
4.3 5.8
2.1
8.3
3.1
2.2
E
0.8
1.0
1.3
2.2
2.2
2.2
2.3
L
5.4
5.4
5.4
5.4
5.8
7.7
5.4
H
0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0
CAT.8100D
ALUMINUM ELECTROLYTIC CAPACITORS
WT
series
Dimensions
V
Cap. (µF)
4
0G
Code
6.3
0J
10
1A
16
1C
25
1E
35
1V
50
1H
0.1
0R1
4 × 5.4 (3) 1.0　0.22
R22
4 × 5.4 (3) 2.6　0.33
R33
4 × 5.4 (3) 3.2　0.47
R47
4 × 5.4 (3) 3.8　1
010
4 × 5.4 (3) 6.3 (5.9)
2.2
2R2
3 × 5.4
7.5　3.3
3R3
3 × 5.4
9　4 × 5.4
14
4.7
4R7
4 × 5.4 (3) 13 (10) 4 × 5.4
15　5 × 5.4
19
5 × 5.4
25　6.3 × 5.4
30
42　51 (45)
10
100
22
220 4 × 5.4
22
4 × 5.4
22
5 × 5.4 27
5 × 5.4
30
6.3 × 5.4
38　6.3 × 5.4
33
330 5 × 5.4
30
5 × 5.4
30
5 × 5.4 35
6.3 × 5.4
40
6.3 × 5.4
48　47
470 5 × 5.4
36
5 × 5.4
36
6.3 × 5.4 46
6.3 × 5.4
50
8 × 5.4
100
101 6.3 × 5.4
60
6.3 × 5.4
60
6.3 × 5.4 60
6.3 × 5.4
60
150
151 6.3 × 5.8
86
6.3 × 5.8
86
6.3 × 5.8 86
6.3 × 7.7
220
221
102 (91)
102 (91) 6.3 × 7.7 105
330
331 6.3 × 7.7
105
6.3 × 7.7
105
8 × 10
470
471 8 × 10
210
8 × 10
210
680
681 8 × 10
210
8 × 10
210
1000
102 8 × 10
230
8 × 10
230
10 × 10
310
1500
152 10 × 10
310
10 × 10
310
4 × 5.4 (3) 18 (14) 8 × 5.4
8 × 5.4
5 × 5.4
23　4 × 5.4 (3) 11 (9)
8 × 5.4
8 × 5.4 59 (52) 6.3 × 7.7
60
66 (59) 6.3 × 5.8
63　6.3 × 7.7
63
6.3 × 7.7
91　6.3 × 7.7
84　8 × 10
140
95
8 × 10
140　8 × 10
155　10 × 10
180
6.3 × 7.7
105
8 × 10
155　8 × 10
190　10 × 10
220
195
8 × 10
195
8 × 10
190　10 × 10
300　8 × 10
210
8 × 10
230
10 × 10
10 × 10
310
10 × 10
310
300　( ) is also available with φ3mm upon request. In such a case, 2 will be put at 12th digit of type numbering system.
Case size Rated
φ D × L (mm) ripple
Rated ripple current (mArms) at 105°C 120Hz
Size φ6.3 × 5.8 is available for capacitors marked. " " In such a case, 6 will be put at 12th digit of type numbering system.
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50　Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UX(p.154), UJ(p.160) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100D