ALUMINUM ELECTROLYTIC CAPACITORS CD Chip Type, Low Impedance series Chip type, low impedance temperature range up to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). Low Impedance CL Low Impedance CD UD Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 6.3 to 100V Rated Capacitance Range 1 to 3300µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 6.3 0.26 10 0.19 16 0.16 25 0.14 35 0.12 50 0.10 63 0.08 80 0.08 100 0.07 For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. Measurement frequency : 120Hz Rated voltage (V) 6.3 10 16 25 35 50 63 80 100 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 3 3 3 3 3 3 Z—25°C / Z+20°C Impecance ratio Z—40°C / Z+20°C ZT / Z20 (MAX.) Z—55°C / Z+20°C Stability at Low Temperature The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours (2000 hours for L 10 mm: 50V or less, and for L 10mm: 63V or more) at 105°C. Endurance Capacitance Change Within ± 30% of the initial capacitance value tan δ 200% or less than the initial specified value 300% or less than the initial specified value for 63V or more Leakage current Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. Chip Type Positive Less than or equal to the initial specified value Leakage current Less than or equal to the initial specified value H 3 4 5 6 7 8 9 Size Package φ4 to 10 Taping φ12.5 to 18 Taping φ12.5 to 18 Tray Capacitance tolerance (±20%) Rated capacitance (100µF) (φ8 × 10, φ10) Positive Pressure 2 relief vent Capacitance Pressure relief vent L ± 1.0 Series Dimension table in next page. H Type φD×L A B C E L H φD×L A ± 0.2 A ± 0.2 E B ± 0.2 φ D ± 0.5 330 µF CD 50V H1015 nichicon C ± 0.2 0.3 MAX. 0.5 MAX. Plastic platform Voltage Lot No. Capacitance Negative H Positive (φ12.5 to φ18) Trade mark L ± 0.5 2 : Except : φ10 × 7.7L Rated voltage (16V) Series name A ± 0.2 A ± 0.2 B±0.2 φD ± 0.5 A2 220E CD Trade mark C ± 0.2 0.5 MAX. Plastic platform 0.3 MAX. Series E Voltage ( E : 25V ) Negative Code GS MS ZD Size code Configuration Negative 1: Size φ8 × 6.2 only Lot No. 10 11 12 13 14 Package code E L ± 0.3 Capacitance 2 A ± 0.2 A ± 0.2 C ± 0.2 B ± 0.2 A2 47 j CD φD ± 0.5 Series 1 UCD 1 C 1 0 1 M C L 1 GS 0.5 MAX. Plastic platform 0.3 MAX. Voltage ( j : 6.3V ) Lot No. Within ± 10% of the initial capacitance value tan δ Type numbering system (Example : 16V 100µF) (φ4 to φ8 × φ6.2) 1 Trade mark Capacitance Change A B C E L H φD Code 4 to 6.3 CL 8 (6.2L) CL 10(7.7L) CL 8 (10L) • 10(10L,13.5L) NL 12.5 to 18 NQ 4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 7.7 10 × 10 2.4 2.4 2.1 3.2 1.8 3.3 2.9 3.2 6.6 6.6 5.3 10.3 4.3 8.3 8.3 10.3 6.6 6.6 5.3 10.3 4.3 8.3 8.3 10.3 2.2 2.2 1.3 4.5 1.0 2.3 3.1 4.5 7.7 5.8 5.8 7.7 5.8 6.2 10 10 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 (mm) 10 × 13.5 12.5 × 13.5 16 × 16.5 18 × 16.5 6.4 5.4 3.2 4.8 19.1 17.1 10.3 13.6 19.1 17.1 13.6 10.3 6.3 6.3 4.5 4.0 16.5 16.5 13.5 13.5 0.8 to 1.1 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 Voltage V 6.3 10 16 25 35 50 63 80 100 Code j A C E V H J K 2A CAT.8100B-1 ALUMINUM ELECTROLYTIC CAPACITORS CD series Dimensions Cap. (µF) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 1 010 4 × 5.8 2.70 60 2.2 2R2 4 × 5.8 2.70 60 3.3 3R3 4 × 5.8 2.70 60 4.7 4R7 60 10 15 22 27 33 47 100 150 220 270 330 470 4 × 5.8 1.35 4 × 5.8 1.35 90 90 5 × 5.8 0.70 4 × 5.8 1.35 90 5 × 5.8 0.70 160 160 4 × 5.8 1.35 5 × 5.8 0.70 160 4 × 5.8 1.35 90 5 × 5.8 0.70 160 6.3 × 5.8 0.36 90 240 4 × 5.8 1.35 4 × 5.8 1.35 90 4 × 5.8 1.35 90 5 × 5.8 0.70 160 5 × 5.8 0.70 160 90 6.3 × 5.8 0.36 5 × 5.8 0.70 160 6.3 × 5.8 0.36 240 240 4 × 5.8 1.35 5 × 5.8 0.70 160 5 × 5.8 0.70 160 6.3 × 5.8 0.36 240 5 × 5.8 0.70 160 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 90 240 4 × 5.8 1.35 90 4 × 5.8 2.70 4 × 5.8 1.35 90 5 × 5.8 1.50 90 5 × 5.8 0.70 160 6.3 × 5.8 0.86 170 5 × 5.8 0.70 160 6.3 × 5.8 0.86 170 6.3 × 5.8 195 240 6.3 × 7.7 0.66 0.36 8 × 6.2 0.63 200 6.3 × 7.7 0.66 195 8 × 6.2 0.63 200 6.3 × 5.8 0.36 240 56 560 5 × 5.8 0.70 160 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 68 680 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 6.3 × 7.7 0.32 290 5 × 5.8 0.70 160 6.3 × 7.7 0.32 290 6.3 × 7.7 0.32 290 8 × 10 0.32 350 6.3 × 5.8 0.36 240 8 × 6.2 0.26 300 8 × 10 0.16 600 10 × 7.7 0.36 330 8 × 10 0.16 600 8 × 10 0.16 600 10 × 7.7 0.18 600 10 × 10 700 600 10 × 7.7 0.16 0.18 10 × 10 0.16 700 100 150 220 330 390 470 680 101 151 221 331 6.3 × 5.8 0.36 6.3 × 5.8 0.36 6.3 × 7.7 0.32 8 × 6.2 0.26 6.3 × 5.8 0.36 240 290 6.3 × 7.7 0.32 290 8 × 10 0.16 600 8 × 10 0.16 600 300 8 × 6.2 0.26 300 10 × 7.7 0.18 600 10 × 7.7 0.18 600 8 × 10 0.16 600 10 × 7.7 0.18 8 × 10 0.16 600 10 × 10 0.08 850 600 6.3 × 7.7 0.32 8 × 6.2 0.26 290 8 × 10 0.16 600 300 10 × 7.7 0.18 600 240 471 681 8 × 10 0.16 600 8 × 10 0.16 600 10 × 7.7 0.18 600 10 × 7.7 0.18 10 × 10 8 × 10 0.16 600 10 × 7.7 0.18 600 8 × 10 0.16 600 600 10 × 7.7 0.18 600 0.08 850 10 × 10 0.08 850 102 8 × 10 0.16 600 10 × 10 0.08 850 10 × 13.5 0.08 1500 152 10 × 10 0.08 850 10 × 13.5 0.08 950 12.5 × 13.5 0.08 2200 222 10 × 13.5 0.08 0.08 1100 3300 332 12.5 × 13.5 0.08 63 80 1J 1K 4.7 4R7 100 220 5 × 5.8 0.08 10 × 13.5 0.08 950 950 12.5 × 13.5 0.08 1100 50 3.00 6.3 × 5.8 1.50 6.3 × 7.7 1.20 120 8 × 6.2 1.20 120 80 0.08 950 12.5 × 13.5 0.08 1100 12.5 × 13.5 0.08 1100 0.14 800 0.12 900 12.5 × 13.5 0.12 900 16 × 16.5 0.073 1610 16 × 16.5 0.073 1610 16 × 16.5 0.035 1800 1100 16 × 16.5 0.035 1800 Case size Rated Impedance φD × L ripple 100 2A 5 × 5.8 5.00 25 6.3 × 5.8 3.00 40 6.3 × 7.7 2.40 60 8 × 6.2 2.40 60 8 × 10 1.30 130 8 × 10 1.30 130 33 330 8 × 10 0.65 250 8 × 10 1.30 130 10 × 10 0.70 200 47 470 8 × 10 0.65 250 10 × 10 0.70 200 12.5 × 13.5 0.32 500 68 680 10 × 10 0.35 400 12.5 × 13.5 0.32 500 12.5 × 13.5 0.32 500 100 101 10 × 10 0.35 400 12.5 × 13.5 0.32 500 16 × 16.5 0.17 793 150 151 12.5 × 13.5 0.16 800 12.5 × 13.5 0.32 500 16 × 16.5 0.17 793 220 221 12.5 × 13.5 0.16 800 18 × 16.5 0.15 917 330 331 0.15 917 470 471 16 × 16.5 0.082 1410 680 681 18 × 16.5 0.08 850 10 × 13.5 10 × 13.5 12.5 × 13.5 (mm) V 3R3 22 950 12.5 × 13.5 10 × 10 1100 Code 3.3 10 290 391 1000 Cap. (µF) 240 0.32 0.36 240 0.36 6.3 × 7.7 6.3 × 5.8 240 6.3 × 5.8 16 × 16.5 0.17 793 18 × 16.5 18 × 16.5 0.15 917 Case size Rated φD × L Impedance ripple (mm) 1690 Max. Impedance (Ω) at 20°C 100kHz, Rated ripple current (mArms) at 105°C 100kHz : In this case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Frequency 50Hz 120Hz 300Hz 1kHz 10kHz or more Coefficient 0.35 0.50 0.64 0.83 1.00 Taping specifications are given in page 23. Recommended land size, soldering by refrow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100B-1