ALUMINUM ELECTROLYTIC CAPACITORS WZ Chip Type, Wide Temperature Range High Temperature (260°C) Reflow series Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec 230°C over 60 sec 2 times (φ8 × 6.2, φ10 × 10 : 1 time) Chip type operating over wide temperature range of to – 55 to +105°C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). WZ High Temperature Reflow WT Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C Tangent of loss angle (tan δ) 6.3 0.30 Rated voltage (V) tan δ (MAX.) 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 40°C / Z+20°C ZT / Z20 (MAX.) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 Within ±25% of the initial capacitance value for capacitors of 16V or less. Within ±20% of the initial capacitance value for capacitors of 25V or more. tan δ 200% or less than the initial specified value Leakage current Less than or equal to the initial specified value Capacitance change After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the tan δ Less than or equal to the initial specified value characteristic requirements listed at right when they are Leakage current Less than or equal to the initial specified value removed from the plate and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 6.3V 33µF) Chip Type (φ4 to φ6.3 ) Positive L Lot No. Capacitance 2 3 4 5 6 7 8 9 10 11 12 13 14 φD 4 to 6.3 (5.4L) 6.3 to 10 (L 5.8L) A±0.2 Configuration A±0.2 Capacitance tolerance (±20%) +0.1 –0.2 (L±0.3) Rated capacitance (33µF) Negative H 1 code GB GS Package code E B±0.2 N2 33C WZ φD±0.5 Series Voltage (C:16V) C±0.2 1 UWZ 0 J 3 3 0 M C L 1G B 0.5 MAX. Plastic platform 0.3 MAX. Rated voltage (6.3V) 1 Apply to φ6.3 × 5.8, φ6.3 × 7.7 (φ8 × 6.2 ) Series name Positive A±0.2 L±0.3 Capacitance Type (mm) A±0.2 B±0.2 φD±0.5 N2 220j WZ Lot No. C±0.2 0.5 MAX. Plastic platform 0.3 MAX. Series Trade mark Negative H (φ8 × 10, φ10×10) Plastic platform 0.3 MAX. 4 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 A 1.8 2.1 2.4 2.4 2.4 3.3 2.9 3.2 B 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 C 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 E 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5 5.4 5.4 5.4 5.4 7.7 6.2 10 10 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 A±0.2 E L±0.5 Lot No. ×L L A±0.2 C±0.2 B±0.2 N2 220E WZ φD±0.5 Series Trade mark 0.5 MAX. Positive Voltage (E:25V) φD E Voltage ( J:6.3V) Capacitance Negative H Voltage V 6.3 10 16 25 35 50 Code j A C E V H Dimension table in next page. CAT.8100Z ALUMINUM ELECTROLYTIC CAPACITORS WZ series Dimensions Cap. (µF) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 0.1 0R1 4 × 5.4 1.0 0.22 R22 4 × 5.4 2.6 0.33 R33 4 × 5.4 3.2 0.47 R47 4 × 5.4 3.8 1 010 4 × 5.4 2.2 2R2 4 × 5.4 11 3.3 3R3 4.7 4R7 6.3 4 × 5.4 14 4 × 5.4 13 4 × 5.4 15 5 × 5.4 19 4 × 5.4 18 5 × 5.4 23 5 × 5.4 25 6.3 × 5.4 30 27 5 × 5.4 30 6.3 × 5.4 38 6.3 × 5.4 42 8 × 6.2 51 5 × 5.4 35 6.3 × 5.4 40 6.3 × 5.4 48 8 × 6.2 59 6.3 × 7.7 60 36 6.3 × 5.4 46 6.3 × 5.4 50 8 × 6.2 66 6.3 × 5.8 63 6.3 × 7.7 63 60 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 7.7 91 6.3 × 7.7 84 8 × 10 140 6.3 × 7.7 95 8 × 10 140 8 × 10 155 10 × 10 180 6.3 × 7.7 105 8 × 10 155 10 × 10 190 10 × 10 220 8 × 10 195 10 × 10 190 10 × 10 300 210 8 × 10 210 10 × 10 300 310 10 × 10 310 10 100 22 220 4 × 5.4 22 5 × 5.4 33 330 5 × 5.4 30 47 470 5 × 5.4 100 101 6.3 × 5.4 150 151 6.3 × 5.8 86 6.3 × 5.8 86 220 221 8 × 6.2 102 6.3 × 7.7 105 330 331 6.3 × 7.7 105 8 × 10 195 470 471 8 × 10 210 8 × 10 680 681 8 × 10 210 10 × 10 1000 102 10 × 10 230 10 × 10 310 1500 152 10 × 10 310 Case size φ D × L (mm) Rated ripple Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100Z