NE - Nichicon

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
NE
High Capacitance
series
Low ESR, High Capacitance, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type : Lead free flow soldering condition
correspondence.
Compliant to the RoHS directive (2011/65/EU).
NU
Higher
Capacitance
NE
Higher
Capacitance
S6
Specifications
Item
Performance Characteristics
Category Temperature Range
–55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range
100 to 1200µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Tangent of loss angle (tan δ)
Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2)
Endurance
Less than or equal to the specified value.
After 2 minutes' application of rated voltage at 20°C
Test condition
105°C, rated voltage 2000Hrs.
Capacitance change
Within ±20% of initial value before test
tan δ
150% or less than the initial specified value
ESR( 1)
150% or less than the initial specified value
Leakage current ( 2)
Less than or equal to the initial specified value
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
Size List
Cap [µF]
R.V.(V)
S.V.(
V)
6.3
10
16
2.8
7.2
11.5
18.4
100
6.3×10
5×8
270
470
8×11.5
8×6
820
(mm)
10×12.5
1000
1200
Stand off
Wire(Lead free)
5×10
220
680
Aluminum case
[φD×L(mm)]
2.5
10×12.5
8×9
Dimension table in next page.
φD×L
φd
P
α
5×8
0.5
2.0
1.0
5×10
0.5
2.0
1.0
6.3×10
0.5
2.5
1.0
8×6
0.6
3.5
1.0
8×9
0.6
3.5
1.0
8×11.5
0.6
3.5
1.5
10×12.5
0.6
5.0
1.5
CAT.8100D
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
NE
series
Standard Ratings
Rated Voltage Surge
Voltage
(V)
(V)
(code)
2.5
(0E)
2.8
6.3
(0J)
7.2
10
(1A)
11.5
16
(1C)
Rated
Capacitance
(µF)
Case Size
φD×L (mm)
tan δ
Leakage
Current
(µA, 2min.)
ESR
(mΩ, 100kHz)
Rated Ripple
Current
(mArms)
NICHICON
FPCAP
680
8×6
0.10
500
8
4900
RNE0E681MDN1□□
FP-2R5RE681M-NE□□
270
5×8
0.10
500
12
3600
RNE0J271MDS1□□
FP-6R3RE271M-NE□□
1200
8×9
0.08
1512
10
5700
RNE0J122MDN1□□
FP-6R3RE122M-NE□□
220
6.3×10
0.08
440
30
2500
RNE1A221MDS1□□
FP-010RE221M-NE□□
100
5×10
0.08
320
35
2300
RNE1C101MDS1□□
FP-016RE101M-NE□□
470
8×11.5
0.08
1504
10
5400
RNE1C471MDN1□□
FP-016RE471M-NE□□
820
10×12.5
0.08
2624
11
5600
RNE1C821MDN1□□
FP-016RE821M-NE□□
1000
10×12.5
0.08
3200
10
6100
RNE1C102MDN1□□
FP-016RE102M-NE□□
18.4
Frequency Characteristics (The frequency characteristics are typical and not a guaranteed value.)
µ
Impedance
µ
Frequency (kHz)
Frequency (kHz)
Taping specifications are given in page 26, 27.
Please refer to page 3 for the minimum order quantity.
CAT.8100D