CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LV Radial Lead Type, Long Life Assurance series High voltage (to 100V), Low ESR, High ripple current. Long life of 3000 hours at 105°C. Radial lead type: Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2002/95/EC). LX LV High Temperature LF High Voltage Long Life Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 16 to 100V Rated Capacitance Range 6.8 to 470µF ± 20% Capacitance Tolerance at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 3000 hours at 105°C. 1.25 1.25 (100kHz) Capacitance change tan δ ESR ( 2) Capacitance change tan δ The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Damp Heat (Steady State) 1) Leakage current ( ESR ( 1) Leakage current ( Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200°C for 60 to 180 seconds and peak temperature at 265°C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. Marking Navy blue print on the case top 2) Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 35V 82µF) Dimensions Resin coated Case Capacitance Tinned lead Wire 1 2 3 4 Lot. No. 6 7 8 9 10 11 12 P±0.5 Size code Configuration Capacitance tolerance (±20%) φd Series 5 P L V 1 V 8 2 0 M D L 1 φ D+0.5 MAX. LV 82 V 012 Voltage(V:35V) L+0.5MAX. Rated capacitance (82µF) 15MIN Rated voltage (35V) 4MIN Series name Type (mm) Size φD L P φd φ8 × 9L 8.0 8.5 3.5 0.6 φ8 × 12L φ10 × 13L 8.0 10.0 11.5 12.5 3.5 5.0 0.6 0.6 Voltage V 16 20 25 35 50 63 80 100 Code C D E V H J K 2A Please refer to page 20 about the end seal configulation. Dimension table in next page. CAT.8100A-1 CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LV series Standard Ratings Rated Voltage (V) code 16 (1C) 20 (1D) 25 (1E) 35 (1V) 50 (1H) 63 (1J) 80 (1K) Case Size φD × L (mm) tan δ Leakage Current (µA) ESR (mΩ) (at 100kHz 20°C) Rated Ripple (mArms) Part Number 220 8×9 0.12 704 26 2100 PLV1C221MCL1 270 8 × 12 0.12 864 24 2500 PLV1C271MDL1 470 10 × 13 0.12 1504 23 2900 PLV1C471MDL1 150 8×9 0.12 600 27 2000 PLV1D151MCL1 220 8 × 12 0.12 880 25 2400 PLV1D221MDL1 330 10 × 13 0.12 1320 24 2800 PLV1D331MDL1 120 8×9 0.12 600 28 2000 PLV1E121MCL1 150 8 × 12 0.12 750 26 2400 PLV1E151MDL1 270 10 × 13 0.12 1350 25 2800 PLV1E271MDL1 56 8×9 0.12 392 29 1900 PLV1V560MCL1 82 8 × 12 0.12 574 27 2300 PLV1V820MDL1 150 10 × 13 0.12 1050 26 2700 PLV1V151MDL1 33 8×9 0.12 330 32 1900 PLV1H330MCL1 39 8 × 12 0.12 390 29 2200 PLV1H390MDL1 68 10 × 13 0.12 680 28 2600 PLV1H680MDL1 22 8×9 0.12 277 35 1800 PLV1J220MCL1 27 8 × 12 0.12 340 33 2100 PLV1J270MDL1 47 10 × 13 0.12 592 29 2600 PLV1J470MDL1 10 8×9 0.12 160 40 1700 PLV1K100MCL1 12 8 × 12 0.12 192 38 1900 PLV1K120MDL1 22 10 × 13 0.12 352 35 2300 PLV1K220MDL1 8×9 0.12 136 45 1600 PLV2A6R8MCL1 10 8 × 12 0.12 200 42 1800 PLV2A100MDL1 18 10 × 13 0.12 360 38 2200 PLV2A180MDL1 Surge Voltage Rated Capacitance (µF) (V) 18.4 23.0 28.7 40.2 57.5 72.4 92 6.8 100 (2A) 115 Rated ripple current (mArms) at 105°C 100kHz Taping specifications are given in page 20, 21, 22. Please refer to page 3 for the minimum order quantity. CAT.8100A-1