R.46 Loose X2 CLASS (IEC 60384-14) - MKP Series Taped Fig.1 METALLIZED POLYPROPYLENE FILM CAPACITOR SELF-HEALING PROPERTIES Fig.2 Typical applications: interference suppression and «across-the-line» applications. Suitable for use in situations where failure of the capacitor would not lead to danger of electric shock. PRODUCT CODE: R46 Insulated rigid leads Insulated flexible leads 0.5mm2 Note: R.46 series has replaced the 1.40 series and 1.47 series. For new design we suggest the use of the R.46 series. Ø d ±0.05 p ≤15 22.5 ≤ p ≤ 27.5 p = 37.5 0.6 or 0.8* 0.8 1 *See size table. All dimensions are in mm. Pitch Box thickness (B) (mm) (mm) Maximum dimensions (mm) B max H max L max 10.0 15.0 15.0 22.5 27.5 37.5 B +0.2 B +0.2 B +0.2 B +0.2 B +0.2 B +0.3 All <7.5 ≥7.5 All All All H +0.1 H +0.1 H +0.1 H +0.1 H +0.1 H +0.1 GENERAL TECHNICAL DATA TEST METHOD AND PERFORMANCE Dielectric: polypropylene film. Damp heat, steady state: Plates: metal layer deposited by evaporation under vacuum. Test conditions 1st Winding: non-inductive type. Temperature: Relative humidity (RH): Test duration: Leads: tinned wire. Protection: plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94 V0. Dielectric strength: no dielectric breakdown or flashover at 4.3 x VR (d.c.)/1 min Capacitance change |∆C/C|: ≤5% Insulation resistance: ≥50% of initial limit. Operating temperature range: -40 to +110°C IEC 60384-14, EN 60384-14. ELECTRICAL CHARACTERISTICS Capacitance range: 275Vac (50/60Hz) / 560 Vdc 300Vac (50/60Hz) / 630 Vdc Endurance: Test conditions Temperature: Test duration: Voltage applied: 0.01µF to 10µF Capacitance values: E6 series (IEC 60063 Norm). ≤10 (6)* at 1kHz * Dielectric strength: no dielectric breakdown or flashover at 4.3 x VR (d.c.)/1 min Capacitance change |∆C/C|: ≤10% Insulation resistance: ≥50% of initial limit. Resistance to soldering heat: Test conditions Insulation resistance: Solder bath temperature: +260°C ± 5°C Dipping time (with heat screen):10 s ± 1 s Test conditions Temperature: Voltage charge time: Voltage charge: Performance ≥1x105 MΩ (5x105 MΩ )* ≥30000 s (150000 s )* +25°C±5°C 1 min 100 Vdc Performance Capacitance change |∆C/C|: ≤2% Winding scheme for C≤0.33µF for C>0.33µF * Typical value single sided metallized polypropylene film Test voltage between terminations (on all pieces): 1500Vac for 1 s + 2200Vdc for 1 s at +25°C±5°C 09/2008 +110°C ± 2°C 1000 h 1.25 x VR +1000Vac 0.1 s/h Performance Capacitance tolerances (measured at 1 kHz): ±10% (K); ±20% (M); tolerance ±5% (J) available upon request Dissipation factor (DF): tgδ 10-4 at +25°C ±5°C: Typical value +60°C ± 2°C 95% ±2% 500 hours Performance Climatic category: 40/110/56 IEC 60068-1 Rated voltage (VR): +40°C ± 2°C 93% ±2% 56 days Test conditions 2nd Temperature: Relative humidity (RH): Test duration: Marking: Manufacturer’s logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric code, climatic category, passive flammability category, manufacturing date code, approvals, manufacturing plant. Related documents: L +0.2 L +0.3 L +0.5 L +0.3 L +0.3 L +0.3 150 R.46 X2 CLASS (IEC 60384-14) - MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR SELF-HEALING PROPERTIES APPROVALS Rated Cap. Ød 275 Vac / 560 Vdc Std dimensions Max dv/dt at 390Vdc Not for use in series with the mains. See www.kemet.com for more information. Part Number (V/ µs) B H L p 0.010 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2100 - - N0 0.015 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2150 - - N0 - 0.022 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2220 - - N0 - 0.033 µF 5.0 11.0 13.0 10.0 0.6 500 R46 KF 2330 - - M1 - 0.047 µF 5.0 11.0 13.0 10.0 0.6 500 R46 KF 2470 - - N0 - - (**) 0.068 µF 6.0 12.0 13.0 10.0 0.6 500 R46 KF 2680 - - M1 - 0.10 µF 6.0 12.0 13.0 10.0 0.6 500 R46 KF 3100 - - M1 M 0.010 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2100 - - 01 - 0.015 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2150 - - 01 - 0.022 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2220 - - 01 - 0.033 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2330 - - 01 - 0.047 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2470 - - 01 - 0.068 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 2680 - - 01 - 0.10 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 3100 - - M1 - 0.15 µF 6.0 12.0 18.0 15.0 0.6 400 R46 KI 3150 - - M2 - 0.15 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3150 - - L2 - 0.22 µF 7.5 13.5 18.0 15.0 0.6 400 R46 KI 3220 - - M2 - 0.22 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3220 - - L2 - 0.22 µF 6.0 17.5 18.0 15.0 0.6 400 R46 KI 3220 - - 02 - 0.33 µF 8.5 14.5 18.0 15.0 0.6 400 R46 KI 3330 - - N0 - 0.33 µF 10.0 16.0 18.0 15.0 0.8 400 R46 KI 3330 - - M1 - 0.33 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3330 - - N1 M - 7.5 18.5 18.0 15.0 0.8 400 R46 KI 3330 - - 02 0.33 µF 13.0 12.0 18.0 15.0 0.8 400 R46 KI 3330 - - 01 - 0.47 µF 7.5 18.5 18.0 15.0 0.8 400 R46 KI 3470 - - 02 M 0.47 µF 10.0 16.0 18.0 15.0 0.8 400 R46 KI 3470 - - N0 M 0.47 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3470 - - M1 - 0.56 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3560 - - N0 - 0.60 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3600 - - N0 - 0.15 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3150 - - 01 - 0.22 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3220 - - M1 - 0.33 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3330 - - N0 - 0.47 µF 7.0 16.0 26.5 22.5 0.8 200 R46 KN 3470 - - N0 - 0.68 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 3680 - - M2 - 1.0 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 4100 - - N2 M 1.0 µF 11.0 20.0 26.5 22.5 0.8 200 R46 KN 4100 - - N1 - 0.47 µF 9.0 17.0 32.0 27.5 0.8 150 R46 KR 3470 - - 01 - 9.0 17.0 32.0 27.5 0.8 150 R46 KR 3680 - - M1 - 1.0 µF 11.0 20.0 32.0 27.5 0.8 150 R46 KR 4100 - - M1 - 1.5 µF 13.0 22.0 32.0 27.5 0.8 150 R46 KR 4150 - - M1 - 2.2 µF 13.0 25.0 32.0 27.5 0.8 150 R46 KR 4220 - - M2 - 2.2 µF 14.0 28.0 32.0 27.5 0.8 150 R46 KR 4220 - - M1 - 3.3 µF 18.0 33.0 32.0 27.5 0.8 150 R46 KR 4330 - - M2 - 4.7 µF 18.0 33.0 32.0 27.5 0.8 150 R46 KR 4470 - - M2 - File No.V4413 UL 1414 (up to 1µF, 85°C; 250Vac) Across-the-line File No.E97797 CSA - C22.2 No.1 (up to 1µF, 85°C; 250Vac) Across-the-line certified for Canada File No.E97797 UL 1283 (310 Vac) Electromagnetic Interference Filters File No.E85238 CSA - C22.2 No.8 (310 Vac) Electromagnetic Interference Filters certified for Canada File No.E85238 GB/T 14472 Class X2 File CQC03001008199 CQC03001008842 (**) ENEC mark has replaced all the following European National marks: Table 1 P2 (mm) Fig. (No.) Pitch (mm) Ordering code (Digit 10 to 11) AMMO-PACK AMMO-PACK 12.70 19.05 1 2 10.0/15.0 22.5 DQ DQ REEL Ø500mm 12.70 19.05 1 2 10.0/15.0 22.5/27.5 CK CK Standard packaging style Lead length (mm) REEL Ø500mm Loose, short leads Loose, long leads Loose, long leads 4.7 µF 22.0 37.0 32.0 27.5 0.8 150 R46 KR 4470 - - M1 - 1.5 µF 11.0 22.0 41.5 37.5 1.0 100 R46 KW 4150 - - M1 - 2.2 µF 11.0 22.0 41.5 37.5 1.0 100 R46 KW 4220 - - M2 M 2.2 µF 13.0 24.0 41.5 37.5 1.0 100 R46 KW 4220 - - M1 - 3.3 µF 16.0 28.5 41.5 37.5 1.0 100 R46 KW 4330 - - M1 - 4.7 µF 16.0 28.5 41.5 37.5 1.0 100 R46 KW 4470 - - M2 M 4.7 µF 19.0 32.0 41.5 37.5 1.0 100 R46 KW 4470 - - M1 - 6.8 µF 20.0 40.0 41.5 37.5 1.0 100 R46 KW 4680 - - M2 - 6.8 µF 24.0 44.0 41.5 37.5 1.0 100 R46 KW 4680 - - M1 - 10.0 µF 30.0 45.0 41.5 37.5 1.0 100 R46 KW 5100 - - M1 - Rated voltage (K=275Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%) Class X2 Approved according to IEC 60384-14 According to IEC 60065 0.33 µF 0.68 µF ENEC IEC 60384-14 Loose, insulated rigid leads Loose, insulated flexible leads Taping style 04 +2 25 -1/+2 30 +5 00 50 40 30 +5 51 150 ±5 52 Note: Ammo-pack is the preferred packaging for taped version. For “capacitor connected in serial with main line” (two - phase and three - phase net) application, please read the “SHORT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS” and contact our Technical Service for choosing the safest solution. All dimensions are in mm E12 Series available upon request 151 09/2008 R.46 X2 CLASS (IEC 60384-14) - MKP Series METALLIZED POLYPROPYLENE FILM CAPACITOR SELF-HEALING PROPERTIES APPROVALS Rated Cap. Ød 275 Vac / 560 Vdc Std dimensions B H L p Part Number Max dv/dt at 390Vdc (**) (V/ µs) 0.033 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2330 - - P0 - 0.047 µF 4.0 9.0 13.0 10.0 0.6 500 R46 KF 2470 - - P0 - 0.068 µF 5.0 11.0 13.0 10.0 0.6 500 R46 KF 2680 - - P0 - 0.1 µF 5.0 11.0 13.0 10.0 0.6 500 R46 KF 3100 - - P1 M 0.1 µF 6.0 12.0 13.0 10.0 0.6 500 R46 KF 3100 - - P0 - 0.15 µF 6.0 12.0 13.0 10.0 0.6 500 R46 KF 3150 - - P0 M 0.15 µF 5.0 11.0 18.0 15.0 0.6 400 R46 KI 3150 - - P0 - 0.22 µF 6.0 12.0 18.0 15.0 0.6 400 R46 KI 3220 - - P0 - 0.33 µF 7.5 13.5 18.0 15.0 0.6 400 R46 KI 3330 - - P0 - 0.33 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3330 - - P1 0.33 µF 6.0 17.5 18.0 15.0 0.6 400 R46 KI 3330 - - P2 0.47 µF 8.5 14.5 18.0 15.0 0.6 400 R46 KI 3470 - - P0 0.47 µF 9.0 12.5 18.0 15.0 0.6 400 R46 KI 3470 - - P1 0.47 µF 6.0 17.5 18.0 15.0 0.6 400 R46 KI 3470 - - P2 M 0.47 µF 7.5 18.5 18.0 15.0 0.8 400 R46 KI 3470 - - P3 M - Class X2 File No.V4413 UL 1414 (up to 1µF, 85°C; 250Vac) Across-the-line File No.E97797 CSA - C22.2 No.1 (up to 1µF, 85°C; 250Vac) Across-the-line certified for Canada File No.E97797 UL 1283 (310 Vac) Electromagnetic Interference Filters File No.E85238 CSA - C22.2 No.8 (310 Vac) Electromagnetic Interference Filters certified for Canada File No.E85238 GB/T 14472 Class X2 File CQC03001008199 CQC03001008842 M 0.68 µF 10.0 16.0 18.0 15.0 0.8 400 R46 KI 3680 - - P1 0.68 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3680 - - P0 - 0.82 µF 11.0 19.0 18.0 15.0 0.8 400 R46 KI 3820 - - P0 M 0.47 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3470 - - P1 - 0.56 µF 6.0 15.0 26.5 22.5 0.8 200 R46 KN 3560 - - P1 M 0.56 µF 7.0 16.0 26.5 22.5 0.8 200 R46 KN 3560 - - P0 - 0.68 µF 7.0 16.0 26.5 22.5 0.8 200 R46 KN 3680 - - P0 - 1.0 µF 8.5 17.0 26.5 22.5 0.8 200 R46 KN 4100 - - P1 M 1.0 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 4100 - - P0 - 1.5 µF 10.0 18.5 26.5 22.5 0.8 200 R46 KN 4150 - - P1 M 1.5 µF 11.0 20.0 26.5 22.5 0.8 200 R46 KN 4150 - - P0 - 2.2 µF 13.0 22.0 26.5 22.5 0.8 200 R46 KN 4220 - - P0 M 1.0 µF 9.0 17.0 32.0 27.5 0.8 150 R46 KR 4100 - - P0 - 1.5 µF 11.0 20.0 32.0 27.5 0.8 150 R46 KR 4150 - - P0 - 2.2 µF 13.0 22.0 32.0 27.5 0.8 150 R46 KR 4220 - - P0 - 3.3 µF 14.0 28.0 32.0 27.5 0.8 150 R46 KR 4330 - - P0 - 4.7 µF 14.0 28.0 32.0 27.5 0.8 150 R46 KR 4470 - - P1 M 4.7 µF 18.0 33.0 32.0 27.5 0.8 150 R46 KR 4470 - - P0 - 6.8 µF 22.0 37.0 32.0 27.5 0.8 150 R46 KR 4680 - - P0 - 2.2 µF 11.0 22.0 41.5 37.5 1.0 100 R46 KW 4220 - - P0 - 3.3 µF 13.0 24.0 41.5 37.5 1.0 100 R46 KW 4330 - - P0 - 4.7 µF 16.0 28.5 41.5 37.5 1.0 100 R46 KW 4470 - - P0 - 6.8 µF 19.0 32.0 41.5 37.5 1.0 100 R46 KW 4680 - - P0 - 10.0 µF 20.0 40.0 41.5 37.5 1.0 100 R46 KW 5100 - - P0 - Rated voltage (K=275Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%) ENEC IEC 60384-14 Approved according to IEC 60384-14 According to IEC 60065 Not for use in series with the mains. See www.kemet.com for more information. (**) ENEC mark has replaced all the following European National marks: Table 1 Standard packaging style Lead length Taping style Ordering code (Digit 10 to 11) P2 (mm) Fig. (No.) Pitch (mm) AMMO-PACK AMMO-PACK 12.70 19.05 1 2 10.0/15.0 22.5 DQ DQ REEL Ø500mm 12.70 19.05 1 2 10.0/15.0 22.5/27.5 CK CK (mm) REEL Ø500mm Loose, short leads Loose, long leads Loose, long leads Loose, insulated rigid leads Loose, insulated flexible leads 04 +2 25 -1/+2 30 +5 00 50 40 30 +5 51 150 ±5 52 Note: Ammo-pack is the preferred packaging for taped version. All dimensions are in mm E12 Series available upon request For “capacitor connected in serial with main line” (two - phase and three - phase net) application, please read the “SHORT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS” and contact our Technical Service for choosing the safest solution. 09/2008 152 R.46 X2 CLASS (IEC 60384-14) - MKP Series Rated Cap. Ød 300 Vac / 630 Vdc Std dimensions Max dv/dt at 390Vdc METALLIZED POLYPROPYLENE FILM CAPACITOR SELF-HEALING PROPERTIES Part Number APPROVALS (V/ µs) B H L p 0.010 µF 4.0 9.0 13.0 10.0 0.6 500 R46 3F 2100 - - N0 - 0.015 µF 4.0 9.0 13.0 10.0 0.6 500 R46 3F 2150 - - N0 - 0.022 µF 4.0 9.0 13.0 10.0 0.6 500 R46 3F 2220 - - N0 - 0.033 µF 5.0 11.0 13.0 10.0 0.6 500 R46 3F 2330 - - M1 - 0.047 µF 5.0 11.0 13.0 10.0 0.6 500 R46 3F 2470 - - N0 - 0.068 µF 6.0 12.0 13.0 10.0 0.6 500 R46 3F 2680 - - M1 - (**) 0.10 µF 6.0 12.0 13.0 10.0 0.6 500 R46 3F 3100 - - M1 M 0.010 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2100 - - 01 - 0.015 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2150 - - 01 - 0.022 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2220 - - 01 - 0.033 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2330 - - 01 - 0.047 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2470 - - 01 - 0.068 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 2680 - - 01 - 0.10 µF 5.0 11.0 18.0 15.0 0.6 400 R46 3I 3100 - - M1 - 0.15 µF 6.0 12.0 18.0 15.0 0.6 400 R46 3I 3150 - - M2 - 0.15 µF 9.0 12.5 18.0 15.0 0.6 400 R46 3I 3150 - - L2 - 0.22 µF 7.5 13.5 18.0 15.0 0.6 400 R46 3I 3220 - - M2 - 0.22 µF 9.0 12.5 18.0 15.0 0.6 400 R46 3I 3220 - - L2 - 0.22 µF 6.0 17.5 18.0 15.0 0.6 400 R46 3I 3220 - - 02 - 0.33 µF 8.5 14.5 18.0 15.0 0.6 400 R46 3I 3330 - - N0 0.33 µF 10.0 16.0 18.0 15.0 0.8 400 R46 3I 3330 - - M1 - 0.33 µF 7.5 18.5 18.0 15.0 0.8 400 R46 3I 3330 - - 02 - 0.33 µF 13.0 12.0 18.0 15.0 0.8 400 R46 3I 3330 - - 01 - 0.47 µF 10.0 16.0 18.0 15.0 0.8 400 R46 3I 3470 - - N0 M 0.47 µF 11.0 19.0 18.0 15.0 0.8 400 R46 3I 3470 - - M1 - 0.56 µF 11.0 19.0 18.0 15.0 0.8 400 R46 3I 3560 - - N0 - 0.60 µF 11.0 19.0 18.0 15.0 0.8 400 R46 3I 3600 - - N0 - 0.15 µF 6.0 15.0 26.5 22.5 0.8 200 R46 3N 3150 - - 01 - 0.22 µF 6.0 15.0 26.5 22.5 0.8 200 R46 3N 3220 - - M1 - 0.33 µF 6.0 15.0 26.5 22.5 0.8 200 R46 3N 3330 - - N0 - 0.47 µF 7.0 16.0 26.5 22.5 0.8 200 R46 3N 3470 - - N0 - 10.0 18.5 26.5 22.5 0.8 200 R46 3N 3680 - - M2 - 10.0 18.5 26.5 22.5 0.8 200 R46 3N 4100 - - N2 M - 11.0 20.0 26.5 22.5 0.8 200 R46 3N 4100 - - N1 9.0 17.0 32.0 27.5 0.8 150 R46 3R 3470 - - 01 - 0.68 µF 9.0 17.0 32.0 27.5 0.8 150 R46 3R 3680 - - M1 - 1.0 µF 11.0 20.0 32.0 27.5 0.8 150 R46 3R 4100 - - M1 - 1.5 µF 13.0 22.0 32.0 27.5 0.8 150 R46 3R 4150 - - M1 - 2.2 µF 13.0 25.0 32.0 27.5 0.8 150 R46 3R 4220 - - M2 - File No.E97797 CSA - C22.2 No.1 (up to 1µF, 85°C; 250Vac) Across-the-line certified for Canada File No.E97797 UL 1283 (310 Vac) Electromagnetic Interference Filters File No.E85238 CSA - C22.2 No.8 (310 Vac) Electromagnetic Interference Filters certified for Canada File No.E85238 GB/T 14472 Class X2 FileCQC03001008199 CQC03001008842 Not for use in series with the mains. See www.kemet.com for more information. Table 1 Standard packaging style Taping style Lead length Ordering code (Digit 10 to 11) Pitch (mm) AMMO-PACK AMMO-PACK 12.70 19.05 1 2 10.0/15.0 22.5 DQ DQ - REEL Ø500mm M REEL Ø500mm 12.70 19.05 1 2 10.0/15.0 22.5/27.5 CK CK 28.0 32.0 27.5 0.8 150 R46 3R 4220 - - M1 - 18.0 33.0 32.0 27.5 0.8 150 R46 3R 4330 - - M2 - 4.7 µF 18.0 33.0 32.0 27.5 0.8 150 R46 3R 4470 - - M2 - 4.7 µF 22.0 37.0 32.0 27.5 0.8 150 R46 3R 4470 - - M1 - 1.5 µF 11.0 22.0 41.5 37.5 1.0 100 R46 3W 4150 - - M1 2.2 µF 11.0 22.0 41.5 37.5 1.0 100 R46 3W 4220 - - M2 (mm) 2.2 µF 13.0 24.0 41.5 37.5 1.0 100 R46 3W 4220 - - M1 - 3.3 µF 16.0 28.5 41.5 37.5 1.0 100 R46 3W 4330 - - M1 - 4.7 µF 16.0 28.5 41.5 37.5 1.0 100 R46 3W 4470 - - M2 M 4.7 µF 19.0 32.0 41.5 37.5 1.0 100 R46 3W 4470 - - M1 - 6.8 µF 20.0 40.0 41.5 37.5 1.0 100 R46 3W 4680 - - M2 - 6.8 µF 24.0 44.0 41.5 37.5 1.0 100 R46 3W 4680 - - M1 - 10.0 µF 30.0 45.0 41.5 37.5 1.0 100 R46 3W 5100 - - M1 - E12 Series available upon request Across-the-line Fig. (No.) 14.0 3.3 µF All dimensions are in mm UL 1414 (up to 1µF, 85°C; 250Vac) P2 (mm) 2.2 µF Rated voltage (3=300Vac) Mechanical version and packaging (Table 1) Tolerance: K (±10%); M (±20%) File No.V4413 (**) ENEC mark has replaced all the following European National marks: 1.0 µF 1.0 µF Class X2 Approved according to IEC 60384-14 According to IEC 60065 0.68 µF 0.47 µF ENEC IEC 60384-14 Loose, short leads Loose, long leads Loose, long leads Loose, insulated rigid leads Loose, insulated flexible leads 04 +2 25 -1/+2 30 +5 00 50 40 30 +5 51 150 ±5 52 Note: Ammo-pack is the preferred packaging for taped version. For “capacitor connected in serial with main line” (two - phase and three - phase net) application, please read the “SHORT GUIDE TO CHOOSE THE RIGHT FILM CAPACITORS” and contact our Technical Service for choosing the safest solution. 153 09/2008