KEMET R46

Loose
R.46
X2 CLASS (IEC 60384-14) - MKP Series
Taped
Fig.1
metallized polyPROPYLENE film capacitor
SELF-HEALING PROPERTIES
Fig.2
Typical applications: interference suppression and
«across-the-line» applications. Suitable for use in situations
where failure of the capacitor would not lead to danger of
electric shock.
PRODUCT CODE: R46
Insulated rigid leads
Ø d ±0.05
Insulated flexible leads 0.5mm2
p ≤15
22.5 ≤ p ≤ 27.5
p = 37.5
0.6 or 0.8*
0.8
1
Note: R.46 series has replaced the 1.40 series and 1.47 series.
For new design we suggest the use of the R.46 series.
*See size table.
All dimensions are in mm.
Pitch Box thickness (B)
(mm)
(mm)
Maximum dimensions (mm)
B max
H max
L max
10.0
15.0
15.0
22.5
27.5
37.5
B +0.2
B +0.2
B +0.2
B +0.2
B +0.2
B +0.3
All
<7.5
≥7.5
All
All
All
H +0.1
H +0.1
H +0.1
H +0.1
H +0.1
H +0.1
GENERAL TECHNICAL DATA
test method and performance
Dielectric: polypropylene film.
Damp heat, steady state:
Plates: metal layer deposited by evaporation under vacuum.
Test conditions 1st
Winding: non-inductive type.
Temperature:
Relative humidity (RH):
Test duration:
Leads: tinned wire.
Protection: plastic case, thermosetting resin filled.
Box material is solvent resistant and flame retardant according to
UL94 V0.
Dielectric strength: no dielectric breakdown or flashover at 4.3 x VR (d.c.)/1 min
Capacitance change |∆C/C|:≤5%
Insulation resistance: ≥50% of initial limit.
Operating temperature range: -40 to +110°C
Rated voltage (VR):
IEC 60384-14, EN 60384-14.
Capacitance range:
275Vac (50/60Hz) / 560 Vdc
300Vac (50/60Hz) / 630 Vdc
Endurance:
Test conditions
Temperature:
Test duration:
Voltage applied:
0.01µF to 10µF
Capacitance values: E6 series (IEC 60063 Norm).
≤10 (6)* at 1kHz *
Dielectric strength: no dielectric breakdown or
flashover at 4.3 x VR (d.c.)/1 min
Capacitance change |∆C/C|:≤10%
Insulation resistance: ≥50% of initial limit.
Resistance to soldering heat:
Test conditions
Insulation resistance:
Test conditions
Temperature:
Voltage charge time:
Voltage charge:
Performance
≥1x105 MΩ (5x105 MΩ )*
≥30000 s (150000 s )*
* Typical value
+25°C±5°C
1 min
100 Vdc
Solder bath temperature: +260°C ± 5°C
Dipping time (with heat screen):10 s ± 1 s
Performance
Capacitance change |∆C/C|:≤2%
Winding scheme
for C≤0.33µF
for C>0.33µF
Test voltage between terminations (on all pieces):
1500Vac for 1 s + 2200Vdc for 1 s at +25°C±5°C
09/2008
+110°C ± 2°C
1000 h
1.25 x VR +1000Vac 0.1 s/h
Performance
Capacitance tolerances (measured at 1 kHz):
±10% (K); ±20% (M);
tolerance ±5% (J) available upon request
Dissipation factor (DF):
tgδ 10-4 at +25°C ±5°C:
Typical value
+60°C ± 2°C
95% ±2%
500 hours
Performance
Climatic category: 40/110/56 IEC 60068-1
electrical characteristics
+40°C ± 2°C
93% ±2%
56 days
Test conditions 2nd
Temperature:
Relative humidity (RH):
Test duration:
Marking: Manufacturer’s logo, series, capacitance, tolerance,
rated voltage, capacitor class, dielectric code, climatic category,
passive flammability category, manufacturing date code, approvals,
manufacturing plant.
Related documents:
L +0.2
L +0.3
L +0.5
L +0.3
L +0.3
L +0.3
single sided metallized
polypropylene film
150
R.46
X2 CLASS (IEC 60384-14) - MKP Series
metallized polyPROPYLENE film capacitor
SELF-HEALING PROPERTIES
APPROVALS
Rated Cap.
275 Vac / 560 Vdc
Std dimensions
Ød
Max
dv/dt at
390Vdc
(V/ µs)
B
H
L
p
0.010 µF
4.0
9.0
13.0
10.0
0.6
500
R46 KF 2100 - - N0 -
0.015 µF
4.0
9.0
13.0
10.0
0.6
500
R46 KF 2150 - - N0 -
0.022 µF
4.0
9.0
13.0
10.0
0.6
500
R46 KF 2220 - - N0 -
0.033 µF
5.0
11.0
13.0
10.0
0.6
500
R46 KF 2330 - - M1 -
0.047 µF
5.0
11.0
13.0
10.0
0.6
500
R46 KF 2470 - - N0 -
0.068 µF
6.0
12.0
13.0
10.0
0.6
500
R46 KF 2680 - - M1 -
0.10 µF
6.0
12.0
13.0
10.0
0.6
500
R46 KF 3100 - - M1 M
0.010 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2100 - - 01
-
0.015 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2150 - - 01
-
0.022 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2220 - - 01
-
0.033 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2330 - - 01
-
0.047 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2470 - - 01
-
0.068 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2680 - - 01
-
0.10 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
3100 - - M1 -
0.15 µF
6.0
12.0
18.0
15.0
0.6
400
R46 KI
3150 - - M2 -
0.15 µF
9.0
12.5
18.0
15.0
0.6
400
R46 KI
3150 - - L2
0.22 µF
7.5
13.5
18.0
15.0
0.6
400
R46 KI
3220 - - M2 -
0.22 µF
9.0
12.5
18.0
15.0
0.6
400
R46 KI
3220 - - L2
-
0.22 µF
6.0
17.5
18.0
15.0
0.6
400
R46 KI
3220 - - 02
-
0.33 µF
8.5
14.5
18.0
15.0
0.6
400
R46 KI
3330 - - N0 -
0.33 µF
10.0
16.0
18.0
15.0
0.8
400
R46 KI
3330 - - M1 -
0.33 µF
9.0
12.5
18.0
15.0
0.6
400
R46 KI
3330 - - N1 M
0.33 µF
7.5
18.5
18.0
15.0
0.8
400
R46 KI
3330 - - 02
-
0.33 µF
13.0
12.0
18.0
15.0
0.8
400
R46 KI
3330 - - 01
-
0.47 µF
7.5
18.5
18.0
15.0
0.8
400
R46 KI
3470 - - 02
M
0.47 µF
10.0
16.0
18.0
15.0
0.8
400
R46 KI
3470 - - N0 M
0.47 µF
11.0
19.0
18.0
15.0
0.8
400
R46 KI
3470 - - M1 -
0.56 µF
11.0
19.0
18.0
15.0
0.8
400
R46 KI
3560 - - N0 -
0.60 µF
11.0
19.0
18.0
15.0
0.8
400
R46 KI
3600 - - N0 -
0.15 µF
6.0
15.0
26.5
22.5
0.8
200
R46 KN 3150 - - 01
0.22 µF
6.0
15.0
26.5
22.5
0.8
200
R46 KN 3220 - - M1 -
0.33 µF
6.0
15.0
26.5
22.5
0.8
200
R46 KN 3330 - - N0 -
0.47 µF
7.0
16.0
26.5
22.5
0.8
200
R46 KN 3470 - - N0 -
0.68 µF
10.0
18.5
26.5
22.5
0.8
200
R46 KN 3680 - - M2 -
1.0 µF
10.0
18.5
26.5
22.5
0.8
200
R46 KN 4100 - - N2 M
1.0 µF
11.0
20.0
26.5
22.5
0.8
200
R46 KN 4100 - - N1 -
0.47 µF
9.0
17.0
32.0
27.5
0.8
150
R46 KR 3470 - - 01
(**)
-
ENEC
IEC 60384-14
Class X2
File No.V4413
UL 1414
(up to 1µF, 85°C;
250Vac)
Across-the-line
File No.E97797
CSA - C22.2 No.1
(up to 1µF, 85°C;
250Vac)
Across-the-line
certified for
Canada
File No.E97797
UL 1283
(310 Vac)
Electromagnetic
Interference
Filters
File No.E85238
CSA - C22.2 No.8
(310 Vac)
Electromagnetic
Interference
Filters certified
for Canada
File No.E85238
GB/T 14472
Class X2
File CQC03001008199
CQC03001008842
Approved according to IEC 60384-14
According to IEC 60065
(**)ENEC mark has replaced all the following European National marks:
-
Table 1
P2
(mm)
Fig.
(No.)
Pitch
(mm)
Ordering
code
(Digit 10 to
11)
AMMO-PACK
AMMO-PACK
12.70
19.05
1
2
10.0/15.0
22.5
DQ
DQ
REEL Ø500mm
12.70
19.05
1
2
10.0/15.0
22.5/27.5
CK
CK
Standard
packaging style
Lead
length
(mm)
-
0.68 µF
9.0
17.0
32.0
27.5
0.8
150
R46 KR 3680 - - M1 -
1.0 µF
11.0
20.0
32.0
27.5
0.8
150
R46 KR 4100 - - M1 -
1.5 µF
13.0
22.0
32.0
27.5
0.8
150
R46 KR 4150 - - M1 -
2.2 µF
13.0
25.0
32.0
27.5
0.8
150
R46 KR 4220 - - M2 -
2.2 µF
14.0
28.0
32.0
27.5
0.8
150
R46 KR 4220 - - M1 -
3.3 µF
18.0
33.0
32.0
27.5
0.8
150
R46 KR 4330 - - M2 -
4.7 µF
18.0
33.0
32.0
27.5
0.8
150
R46 KR 4470 - - M2 -
4.7 µF
22.0
37.0
32.0
27.5
0.8
150
R46 KR 4470 - - M1 -
1.5 µF
11.0
22.0
41.5
37.5
1.0
100
R46 KW 4150 - - M1 -
2.2 µF
11.0
22.0
41.5
37.5
1.0
100
R46 KW 4220 - - M2 M
2.2 µF
13.0
24.0
41.5
37.5
1.0
100
R46 KW 4220 - - M1 -
3.3 µF
16.0
28.5
41.5
37.5
1.0
100
R46 KW 4330 - - M1 -
4.7 µF
16.0
28.5
41.5
37.5
1.0
100
R46 KW 4470 - - M2 M
4.7 µF
19.0
32.0
41.5
37.5
1.0
100
R46 KW 4470 - - M1 -
6.8 µF
20.0
40.0
41.5
37.5
1.0
100
R46 KW 4680 - - M2 -
6.8 µF
24.0
44.0
41.5
37.5
1.0
100
R46 KW 4680 - - M1 -
10.0 µF
30.0
45.0
41.5
37.5
1.0
100
R46 KW 5100 - - M1 -
Rated voltage (K=275Vac)
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
Not for new design.
Not for use in series with the mains.
See www.kemet.com for more information.
Part Number
REEL Ø500mm
Loose, short leads
Loose, long leads
Loose, long leads
Loose, insulated
rigid leads
Loose, insulated
flexible leads
Taping style
04 +2
25 -1/+2
30 +5
00
50
40
30 +5
51
150 ±5
52
Note: Ammo-pack is the preferred packaging for taped version.
For “capacitor connected in serial with main line” (two - phase and
three - phase net) application, please read the “SHORT GUIDE TO
CHOOSE THE RIGHT FILM CAPACITORS” and contact
our Technical Service for choosing the safest solution.
All dimensions are in mm
E12 Series available upon request
151
09/2008
R.46
X2 CLASS (IEC 60384-14) - MKP Series
metallized polyPROPYLENE film capacitor
SELF-HEALING PROPERTIES
APPROVALS
Rated Cap.
275 Vac / 560 Vdc
Std dimensions
B
H
L
Ød
p
Max
dv/dt at
390Vdc
Part Number
(**)
(V/ µs)
0.033 µF
4.0
9.0
13.0
10.0
0.6
500
R46 KF 2330 - - P0
-
0.047 µF
4.0
9.0
13.0
10.0
0.6
500
R46 KF 2470 - - P0
-
0.068 µF
5.0
11.0
13.0
10.0
0.6
500
R46 KF 2680 - - P0
-
0.1 µF
5.0
11.0
13.0
10.0
0.6
500
R46 KF 3100 - - P1
M
0.1 µF
6.0
12.0
13.0
10.0
0.6
500
R46 KF 3100 - - P0
-
0.15 µF
6.0
12.0
13.0
10.0
0.6
500
R46 KF 3150 - - P0
M
0.15 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
3150 - - P0
-
0.22 µF
6.0
12.0
18.0
15.0
0.6
400
R46 KI
3220 - - P0
-
0.33 µF
7.5
13.5
18.0
15.0
0.6
400
R46 KI
3330 - - P0
-
0.33 µF
9.0
12.5
18.0
15.0
0.6
400
R46 KI
3330 - - P1
0.33 µF
6.0
17.5
18.0
15.0
0.6
400
R46 KI
3330 - - P2
0.47 µF
8.5
14.5
18.0
15.0
0.6
400
R46 KI
3470 - - P0
-
0.47 µF
9.0
12.5
18.0
15.0
0.6
400
R46 KI
3470 - - P1
M
0.47 µF
6.0
17.5
18.0
15.0
0.6
400
R46 KI
3470 - - P2
M
0.47 µF
7.5
18.5
18.0
15.0
0.8
400
R46 KI
3470 - - P3
-
0.68 µF
10.0
16.0
18.0
15.0
0.8
400
R46 KI
3680 - - P1
M
0.68 µF
11.0
19.0
18.0
15.0
0.8
400
R46 KI
3680 - - P0
-
0.82 µF
11.0
19.0
18.0
15.0
0.8
400
R46 KI
3820 - - P0
M
0.47 µF
6.0
15.0
26.5
22.5
0.8
200
R46 KN 3470 - - P1
-
0.56 µF
6.0
15.0
26.5
22.5
0.8
200
R46 KN 3560 - - P1
M
0.56 µF
7.0
16.0
26.5
22.5
0.8
200
R46 KN 3560 - - P0
-
0.68 µF
7.0
16.0
26.5
22.5
0.8
200
R46 KN 3680 - - P0
-
1.0 µF
8.5
17.0
26.5
22.5
0.8
200
R46 KN 4100 - - P1
M
1.0 µF
10.0
18.5
26.5
22.5
0.8
200
R46 KN 4100 - - P0
-
1.5 µF
10.0
18.5
26.5
22.5
0.8
200
R46 KN 4150 - - P1
M
1.5 µF
11.0
20.0
26.5
22.5
0.8
200
R46 KN 4150 - - P0
-
2.2 µF
13.0
22.0
26.5
22.5
0.8
200
R46 KN 4220 - - P0
M
1.0 µF
9.0
17.0
32.0
27.5
0.8
150
R46 KR 4100 - - P0
-
1.5 µF
11.0
20.0
32.0
27.5
0.8
150
R46 KR 4150 - - P0
-
2.2 µF
13.0
22.0
32.0
27.5
0.8
150
R46 KR 4220 - - P0
-
3.3 µF
14.0
28.0
32.0
27.5
0.8
150
R46 KR 4330 - - P0
-
4.7 µF
14.0
28.0
32.0
27.5
0.8
150
R46 KR 4470 - - P1
M
4.7 µF
18.0
33.0
32.0
27.5
0.8
150
R46 KR 4470 - - P0
-
6.8 µF
22.0
37.0
32.0
27.5
0.8
150
R46 KR 4680 - - P0
-
2.2 µF
11.0
22.0
41.5
37.5
1.0
100
R46 KW 4220 - - P0
-
3.3 µF
13.0
24.0
41.5
37.5
1.0
100
R46 KW 4330 - - P0
-
4.7 µF
16.0
28.5
41.5
37.5
1.0
100
R46 KW 4470 - - P0
-
6.8 µF
19.0
32.0
41.5
37.5
1.0
100
R46 KW 4680 - - P0
-
10.0 µF
20.0
40.0
41.5
37.5
1.0
100
R46 KW 5100 - - P0
-
Rated voltage (K=275Vac)
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
ENEC
IEC 60384-14
Class X2
File No.V4413
UL 1414
(up to 1µF, 85°C;
250Vac)
Across-the-line
File No.E97797
CSA - C22.2 No.1
(up to 1µF, 85°C;
250Vac)
Across-the-line
certified for
Canada
File No.E97797
UL 1283
(310 Vac)
Electromagnetic
Interference
Filters
File No.E85238
CSA - C22.2 No.8
(310 Vac)
Electromagnetic
Interference
Filters certified
for Canada
File No.E85238
GB/T 14472
Class X2
File
CQC03001008199
CQC03001008842
Approved according to IEC 60384-14
According to IEC 60065
Not for use in series with the mains.
See www.kemet.com for more information.
.
(**)ENEC mark has replaced all the following European National marks:
Table 1
Standard
packaging style
Lead
length
Taping style
Ordering
code
(Digit 10 to 11)
P2
(mm)
Fig.
(No.)
Pitch
(mm)
AMMO-PACK
AMMO-PACK
12.70
19.05
1
2
10.0/15.0
22.5
DQ
DQ
REEL Ø500mm
12.70
19.05
1
2
10.0/15.0
22.5/27.5
CK
CK
(mm)
REEL Ø500mm
Loose, short leads
Loose, long leads
Loose, long leads
Loose, insulated
rigid leads
Loose, insulated
flexible leads
04 +2
25 -1/+2
30 +5
00
50
40
30 +5
51
150 ±5
52
Note: Ammo-pack is the preferred packaging for taped version.
All dimensions are in mm
E12 Series available upon request
For “capacitor connected in serial with main line” (two - phase and
three - phase net) application, please read the “SHORT GUIDE TO
CHOOSE THE RIGHT FILM CAPACITORS” and contact
our Technical Service for choosing the safest solution.
09/2008
152
R.46
X2 CLASS (IEC 60384-14) - MKP Series
Rated Cap.
300 Vac / 630 Vdc
Std dimensions
Ød
Max
dv/dt at
390Vdc
metallized polyPROPYLENE film capacitor
SELF-HEALING PROPERTIES
Part Number
APPROVALS
(V/ µs)
B
H
L
p
0.010 µF
4.0
9.0
13.0
10.0
0.6
500
R46 3F
2100 - - N0 -
0.015 µF
4.0
9.0
13.0
10.0
0.6
500
R46 3F
2150 - - N0 -
0.022 µF
4.0
9.0
13.0
10.0
0.6
500
R46 3F
2220 - - N0 -
0.033 µF
5.0
11.0
13.0
10.0
0.6
500
R46 3F
2330 - - M1 -
0.047 µF
5.0
11.0
13.0
10.0
0.6
500
R46 3F
2470 - - N0 -
0.068 µF
6.0
12.0
13.0
10.0
0.6
500
R46 3F
2680 - - M1 -
(**)
0.10 µF
6.0
12.0
13.0
10.0
0.6
500
R46 3F
3100 - - M1 M
0.010 µF
5.0
11.0
18.0
15.0
0.6
400
R46 3I
2100 - - 01
-
0.015 µF
5.0
11.0
18.0
15.0
0.6
400
R46 3I
2150 - - 01
-
0.022 µF
5.0
11.0
18.0
15.0
0.6
400
R46 3I
2220 - - 01
-
0.033 µF
5.0
11.0
18.0
15.0
0.6
400
R46 3I
2330 - - 01
-
0.047 µF
5.0
11.0
18.0
15.0
0.6
400
R46 3I
2470 - - 01
-
0.068 µF
5.0
11.0
18.0
15.0
0.6
400
R46 3I
2680 - - 01
-
0.10 µF
5.0
11.0
18.0
15.0
0.6
400
R46 3I
3100 - - M1 -
0.15 µF
6.0
12.0
18.0
15.0
0.6
400
R46 3I
3150 - - M2 -
0.15 µF
9.0
12.5
18.0
15.0
0.6
400
R46 3I
3150 - - L2
0.22 µF
7.5
13.5
18.0
15.0
0.6
400
R46 3I
3220 - - M2 -
0.22 µF
9.0
12.5
18.0
15.0
0.6
400
R46 3I
3220 - - L2
-
0.22 µF
6.0
17.5
18.0
15.0
0.6
400
R46 3I
3220 - - 02
-
0.33 µF
8.5
14.5
18.0
15.0
0.6
400
R46 3I
3330 - - N0 -
0.33 µF
10.0
16.0
18.0
15.0
0.8
400
R46 3I
3330 - - M1 -
0.33 µF
7.5
18.5
18.0
15.0
0.8
400
R46 3I
3330 - - 02
-
0.33 µF
13.0
12.0
18.0
15.0
0.8
400
R46 3I
3330 - - 01
-
0.47 µF
10.0
16.0
18.0
15.0
0.8
400
R46 3I
3470 - - N0 M
0.47 µF
11.0
19.0
18.0
15.0
0.8
400
R46 3I
3470 - - M1 -
0.56 µF
11.0
19.0
18.0
15.0
0.8
400
R46 3I
3560 - - N0 -
0.60 µF
11.0
19.0
18.0
15.0
0.8
400
R46 3I
3600 - - N0 -
0.15 µF
6.0
15.0
26.5
22.5
0.8
200
R46 3N 3150 - - 01
0.22 µF
6.0
15.0
26.5
22.5
0.8
200
R46 3N 3220 - - M1 -
0.33 µF
6.0
15.0
26.5
22.5
0.8
200
R46 3N 3330 - - N0 -
0.47 µF
7.0
16.0
26.5
22.5
0.8
200
R46 3N 3470 - - N0 -
0.68 µF
10.0
18.5
26.5
22.5
0.8
200
R46 3N 3680 - - M2 -
1.0 µF
10.0
18.5
26.5
22.5
0.8
200
R46 3N 4100 - - N2 M
-
-
11.0
20.0
26.5
22.5
0.8
200
R46 3N 4100 - - N1 -
9.0
17.0
32.0
27.5
0.8
150
R46 3R 3470 - - 01
0.68 µF
9.0
17.0
32.0
27.5
0.8
150
R46 3R 3680 - - M1 -
1.0 µF
11.0
20.0
32.0
27.5
0.8
150
R46 3R 4100 - - M1 -
1.5 µF
13.0
22.0
32.0
27.5
0.8
150
R46 3R 4150 - - M1 -
2.2 µF
13.0
25.0
32.0
27.5
0.8
150
R46 3R 4220 - - M2 -
2.2 µF
14.0
28.0
32.0
27.5
0.8
150
R46 3R 4220 - - M1 -
3.3 µF
18.0
33.0
32.0
27.5
0.8
150
R46 3R 4330 - - M2 -
4.7 µF
18.0
33.0
32.0
27.5
0.8
150
R46 3R 4470 - - M2 -
4.7 µF
22.0
37.0
32.0
27.5
0.8
150
R46 3R 4470 - - M1 -
1.5 µF
11.0
22.0
41.5
37.5
1.0
100
R46 3W 4150 - - M1 -
2.2 µF
11.0
22.0
41.5
37.5
1.0
100
R46 3W 4220 - - M2 M
UL 1414
(up to 1µF, 85°C;
250Vac)
Across-the-line
File No.E97797
CSA - C22.2 No.1
(up to 1µF, 85°C;
250Vac)
Across-the-line
certified for
Canada
File No.E97797
UL 1283
(310 Vac)
Electromagnetic
Interference
Filters
File No.E85238
CSA - C22.2 No.8
(310 Vac)
Electromagnetic
Interference
Filters certified for
Canada
File No.E85238
GB/T 14472
Class X2
FileCQC03001008199
CQC03001008842
Not for use in series with the mains.
See www.kemet.com for more information.
-
Table 1
Standard
packaging style
Lead
length
2.2 µF
13.0
24.0
41.5
37.5
1.0
100
R46 3W 4220 - - M1 -
16.0
28.5
41.5
37.5
1.0
100
R46 3W 4330 - - M1 -
4.7 µF
16.0
28.5
41.5
37.5
1.0
100
R46 3W 4470 - - M2 M
4.7 µF
19.0
32.0
41.5
37.5
1.0
100
R46 3W 4470 - - M1 -
6.8 µF
20.0
40.0
41.5
37.5
1.0
100
R46 3W 4680 - - M2 -
6.8 µF
24.0
44.0
41.5
37.5
1.0
100
R46 3W 4680 - - M1 -
10.0 µF
30.0
45.0
41.5
37.5
1.0
100
R46 3W 5100 - - M1 -
Taping style
Ordering
code
(Digit 10 to 11)
P2
(mm)
Fig.
(No.)
Pitch
(mm)
AMMO-PACK
AMMO-PACK
12.70
19.05
1
2
10.0/15.0
22.5
DQ
DQ
REEL Ø500mm
12.70
19.05
1
2
10.0/15.0
22.5/27.5
CK
CK
(mm)
3.3 µF
E12 Series available upon request
File No.V4413
(**)ENEC mark has replaced all the following European National marks:
1.0 µF
All dimensions are in mm
Class X2
Approved according to IEC 60384-14
According to IEC 60065
0.47 µF
Rated voltage (3=300Vac)
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
ENEC
IEC 60384-14
REEL Ø500mm
Loose, short leads
Loose, long leads
Loose, long leads
Loose, insulated
rigid leads
Loose, insulated
flexible leads
04 +2
25 -1/+2
30 +5
00
50
40
30 +5
51
150 ±5
52
Note: Ammo-pack is the preferred packaging for taped version.
For “capacitor connected in serial with main line” (two - phase and
three - phase net) application, please read the “SHORT GUIDE TO
CHOOSE THE RIGHT FILM CAPACITORS” and contact
our Technical Service for choosing the safest solution.
153
09/2008
Loose
R.46
Taped
Fig.1
X2 CLASS (IEC 60384-14) - MKP
metallized POLYpropylene film CAPACITOR
SELF-HEALING PROPERTIES
Fig.2
Typical applications: interference suppression and «acrossthe-line» applications. Suitable for use in situations where
failure of the capacitor would not lead to danger of electric
shock.
PRODUCT CODE: R46
Ø d ±0.05
p ≤15
p = 22.5
0.6 or 0.8*
0.8
Not for use in series with the mains.
See www.kemet.com for more information.
NEW 125°C
*See size table.
All dimensions are in mm.
GENERAL TECHNICAL DATA
Dielectric: polypropylene film.
Plates: metal layer deposited by evaporation under vacuum.
Winding: non-inductive type.
Leads: tinned wire.
Protection: plastic case, thermosetting resin filled. Box material is
solvent resistant and flame retardant according to UL94 V0.
Marking: Manufacturer’s logo, series, capacitance, tolerance,
rated voltage, capacitor class, dielectric code, climatic category,
passive flammability category, manufacturing date code, approvals,
manufacturing plant.
Climatic category: 40/125/56 IEC 60068-1
Operating temperature range: -40 to +125°C
Related documents:
IEC 60384-14; EN 60384-14
Rated
Cap.
electrical characteristics
Rated voltage (VR):
Capacitance range:
275 Vac (50/60Hz) / 560 Vdc
0.01µF to 1µF
test method and performance
Endurance:
Test conditions
Temperature:
Test duration:
+125°C±2°C
1000 h
Voltage applied: 1.25 x VR +1000Vac 0.1 s/h
Performance
Dielectric strength: no dielectric breakdown or
flashover at 4.3 x VR (d.c.)/1 min
Capacitance change |∆C/C|: ≤10%
Insulation resistance:
≥
50% of initial limit.
Approvals
(**)
ENEC
IEC 60384-14
Class X2
File No.CA08.00063
275 Vac / 560 Vdc
Std dimensions
B
H
L
Ød
p
Max
dv/dt at
390Vdc
(V/ µs)
0.010 µF
5.0
11.0
13.0
10.0
0.6
500
R46 K F 2100 - - H1 -
0.015 µF
5.0
11.0
13.0
10.0
0.6
500
R46 K F 2150 - - H1 -
0.022 µF
5.0
11.0
13.0
10.0
0.6
500
R46 K F 2220 - - H1 -
0.033 µF
5.0
11.0
13.0
10.0
0.6
500
R46 K F 2330 - - H1 -
0.047 µF
6.0
12.0
13.0
10.0
0.6
500
R46 K F 2470 - - H1 -
0.068 µF
6.0
12.0
13.0
10.0
0.6
500
R46 K F 2680 - - H1 M
0.010 µF
5.0
11.0
18.0
15.0
0.6
400
R46 K I
2100 - - H1 -
0.015 µF
5.0
11.0
18.0
15.0
0.6
400
R46 K I
2150 - - H1 -
0.022 µF
5.0
11.0
18.0
15.0
0.6
400
R46 K I
2220 - - H1 -
0.033 µF
5.0
11.0
18.0
15.0
0.6
400
R46 K I
2330 - - H1 -
0.047 µF
5.0
11.0
18.0
15.0
0.6
400
R46 K I
2470 - - H1 -
0.068 µF
5.0
11.0
18.0
15.0
0.6
400
R46 K I
2680 - - H1 -
0.10 µF
6.0
12.0
18.0
15.0
0.6
400
R46 K I
3100 - - H1 -
0.15 µF
6.0
17.5
18.0
15.0
0.6
400
R46 K I
3150 - - H2 -
0.15 µF
9.0
12.5
18.0
15.0
0.6
400
R46 K I
3150 - - H3 -
0.15 µF
7.5
13.5
18.0
15.0
0.6
400
R46 K I
3150 - - H1 -
0.22 µF
8.5
14.5
18.0
15.0
0.6
400
R46 K I
3220 - - H1 -
0.22 µF
6.0
17.5
18.0
15.0
0.6
400
R46 K I
3220 - - H2 M
0.22 µF
9.0
12.5
18.0
15.0
0.6
400
R46 K I
3220 - - H3 M
0.22 µF
7.5
18.5
18.0
15.0
0.8
400
R46 K I
3220 - - H4 -
0.33 µF
10.0
16.0
18.0
15.0
0.8
400
R46 K I
3330 - - H1 M
3330 - - H2 M
0.33 µF
7.5
18.5
18.0
15.0
0.8
400
R46 K I
0.33 µF
13.0
12.0
18.0
15.0
0.8
400
R46 K I
3330 - - H3 M
0.47 µF
11.0
19.0
18.0
15.0
0.8
400
R46 K I
3470 - - H1 M
0.15 µF
6.0
15.0
26.5
22.5
0.8
200
R46 K N 3150 - - H1 -
0.22 µF
6.0
15.0
26.5
22.5
0.8
200
R46 K N 3220 - - H1 -
0.33 µF
7.0
16.0
26.5
22.5
0.8
200
R46 K N 3330 - - H1 -
0.47 µF
10.0
18.5
26.5
22.5
0.8
200
R46 K N 3470 - - H1 -
0.68 µF
11.0
20.0
26.5
22.5
0.8
200
R46 K N 3680 - - H1 -
1.0 µF
13.0
22.0
26.5
22.5
0.8
200
R46 K N 4100 - - H1 -
UL 1414
(up to 1µF, 85°C;
250Vac)
Across-the-line
CSA - C22.2 No.1
(up to 1µF, 85°C;
250Vac)
Across-the-line
certified for
Canada
File No.E97797
UL 1283
(310 Vac)
Electromagnetic
Interference
Filters
File No.E85238
Rated voltage (K=275Vac)
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
CSA - C22.2 No.8
(310 Vac)
Electromagnetic
Interference
Filters certified
for Canada
File No.E85238
300Vac available upon request
E12 Series available upon request
Approved according to IEC 60384-14
According to IEC 60065
File No.E97797
(**) ENEC mark has replaced all the following European National
marks:
09/2008
Part Number
All dimensions are in mm
For “capacitor connected in serial with main line” (two - phase and
three - phase net) application, please read the “SHORT GUIDE TO
CHOOSE THE RIGHT FILM CAPACITORS” and contact
our Technical Service for choosing the safest solution.
154
R.46 S
Loose
X2 CLASS (IEC 60384-14) - MKP Series
metallized polyPROPYLENE film capacitor
SELF-HEALING PROPERTIES
Taped
Fig.1
VERSION
Fig.2
Typical applications: This special R46 release is designed
for applications in series with the main
.
PRODUCT CODE: R46
Not for new design.
Not for use in series with the mains.
See www.kemet.com for more information.
Ø d ±0.05
p ≤15
22.5 ≤ p ≤ 27.5
p = 37.5
0.6 or 0.8*
0.8
1.0
*See size table.
All dimensions are in mm.
Pitch Box thickness (B)
(mm)
(mm)
Maximum dimensions (mm)
B max
H max
L max
10.0
15.0
15.0
22.5
27.5
37.5
B +0.2
B +0.2
B +0.2
B +0.2
B +0.2
B +0.3
All
<7.5
≥7.5
All
All
All
H +0.1
H +0.1
H +0.1
H +0.1
H +0.1
H +0.1
GENERAL TECHNICAL DATA
test method and performance
Dielectric: polypropylene film.
Damp heat, steady state:
Plates: metal layer deposited by evaporation under vacuum.
Test conditions 1st
Winding: non-inductive type.
Temperature:
+40°C ± 2°C
Relative humidity (RH): 93% ±2%
Test duration:
56 days
Leads: tinned wire.
Protection: plastic case, thermosetting resin filled.
Box material is solvent resistant and flame retardant according to
UL94 V0.
Test conditions 2nd
Temperature:
+60°C ± 2°C
Relative humidity (RH): 95% ±2%
Test duration:
500 hours
Marking: Manufacturer’s logo, series, capacitance, tolerance,
rated voltage, capacitor class, dielectric code, climatic category,
passive flammability category, manufacturing date code, approvals,
manufacturing plant.
Test conditions 3rd
Temperature:
+40°C ± 2°C
Relative humidity (RH): 93% ±2%
Test duration:
500 hours
Voltage value:
230 Vac, 50 Hz
Climatic category: 40/110/56 IEC 60068-1
Operating temperature range: -40 to +110°C
Related documents:
IEC 60384-14, EN 60384-14.
electrical characteristics
Rated voltage (VR):
Capacitance range:
275Vac (50/60Hz) / 560 Vdc
Performance
Dielectric strength: no dielectric breakdown or flashover at 4.3 x VR (d.c.)/1 min
Capacitance change |∆C/C|:≤5%
Insulation resistance: ≥50% of initial limit.
0.022µF to 10µF
Capacitance values: E6 series (IEC 60063 Norm).
Capacitance tolerances (measured at 1 kHz):
±10% (K); ±20% (M).
tolerance ±5% (J) available upon request
Endurance:
Test conditions
Temperature:
Test duration:
Voltage applied:
Dissipation factor (DF):
tgδ 10-4 at +25°C ±5°C: ≤15 (8)* at 1kHz
* Typical value
Temperature:
Voltage charge time:
Voltage charge:
Performance
≥1x105 MΩ (5x105 MΩ )*
≥30000 s (150000 s )*
* Typical value
+25°C±5°C
1 min
100 Vdc
+110°C ± 2°C
1000 h
1.25 x VR +1000Vac 0.1 s/h
Performance
Insulation resistance:
Test conditions
L +0.2
L +0.3
L +0.5
L +0.3
L +0.3
L +0.3
Dielectric strength:
no dielectric breakdown or
flashover at 4.3 x VR (d.c.)/1 min
Capacitance change |∆C/C|:≤10%
Insulation resistance: ≥50% of initial limit.
Resistance to soldering heat:
Test conditions
for C≤0.33µF
for C>0.33µF
Solder bath temperature: +260°C ± 5°C
Dipping time (with heat screen):10 s ± 1 s
Test voltage between terminations (on all pieces):
1500Vac for 1 s + 2200Vdc for 1 s at +25°C±5°C
Performance
Capacitance change |∆C/C|:≤2%
155
09/2008
R.46 S
VERSION
X2 CLASS (IEC60384-14) - MKP Series
metallized polyPROPYLENE film capacitor
SELF-HEALING PROPERTIES
APPROVALS
Rated Cap.
(*)
275 Vac / 560 Vdc
Std dimensions
B
H
L
Ød
p
Max
dv/dt at
390Vdc
Part Number
(**)
(V/ µs)
0.010 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2100 - - S0
-
0.015 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2150 - - S0
-
0.022 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2220 - - S0
-
0.033 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2330 - - S0
-
0.047 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2470 - - S1
-
0.068 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
2680 - - S0
-
0.10 µF
5.0
11.0
18.0
15.0
0.6
400
R46 KI
3100 - - S1
M
0.10 µF
6.0
12.0
18.0
15.0
0.6
400
R46 KI
3100 - - S0
-
0.15 µF
6.0
12.0
18.0
15.0
0.6
400
R46 KI
3150 - - S1
M
0.15 µF
7.5
13.5
18.0
15.0
0.6
400
R46 KI
3150 - - S0
-
0.15 µF
9.0
12.5
18.0
15.0
0.6
400
R46 KI
3150 - - S3
-
0.22 µF
7.5
13.5
18.0
15.0
0.6
400
R46 KI
3220 - - S1
M
0.22 µF
8.5
14.5
18.0
15.0
0.6
400
R46 KI
3220 - - S0
-
0.22 µF
6.0
17.5
18.0
15.0
0.6
400
R46 KI
3220 - - S2
-
0.22 µF
9.0
12.5
18.0
15.0
0.6
400
R46 KI
3220 - - S3
-
0.33 µF
13.0
12.0
18.0
15.0
0.8
400
R46 KI
3330 - - S1
-
0.33 µF
8.5
14.5
18.0
15.0
0.8
400
R46 KI
3330 - - S3
M
0.33 µF
10.0
16.0
18.0
15.0
0.8
400
R46 KI
3330 - - S0
-
0.33 µF
7.5
18.5
18.0
15.0
0.8
400
R46 KI
3330 - - S2
-
0.47 µF
11.0
19.0
18.0
15.0
0.8
400
R46 KI
3470 - - S0
-
0.47 µF
10.0
16.0
18.0
15.0
0.8
400
R46 KI
3470 - - S1
M
0.56 µF
11.0
19.0
18.0
15.0
0.8
400
R46 KI
3560 - - S0
-
3680 - - S0
M
0.68 µF
11.0
19.0
18.0
15.0
0.8
400
R46 KI
0.22 µF
6.0
15.0
26.5
22.5
0.8
200
R46 KN 3220 - - S0
-
0.33 µF
6.0
15.0
26.5
22.5
0.8
200
R46 KN 3330 - - S1
M
0.33 µF
7.0
16.0
26.5
22.5
0.8
200
R46 KN 3330 - - S0
-
0.47 µF
7.0
16.0
26.5
22.5
0.8
200
R46 KN 3470 - - S1
M
0.47 µF
8.5
17.0
26.5
22.5
0.8
200
R46 KN 3470 - - S0
-
0.68 µF
10.0
18.5
26.5
22.5
0.8
200
R46 KN 3680 - - S0
-
1.0 µF
10.0
18.5
26.5
22.5
0.8
200
R46 KN 4100 - - S2
M
1.0 µF
11.0
20.0
26.5
22.5
0.8
200
R46 KN 4100 - - S1
-
1.2 µF
13.0
22.0
26.5
22.5
0.8
200
R46 KN 4120 - - S0
-
0.47 µF
9.0
17.0
32.0
27.5
0.8
150
R46 KR 3470 - - S0
-
0.68 µF
9.0
17.0
32.0
27.5
0.8
150
R46 KR 3680 - - S1
-
1.0 µF
11.0
20.0
32.0
27.5
0.8
150
R46 KR 4100 - - S1
-
1.5 µF
13.0
22.0
32.0
27.5
0.8
150
R46 KR 4150 - - S1
-
2.2 µF
13.0
25.0
32.0
27.5
0.8
150
R46 KR 4220 - - S2
3.3 µF
18.0
33.0
32.0
27.5
0.8
150
R46 KR 4330 - - S2
4.7 µF
18.0
33.0
32.0
27.5
0.8
150
1.5 µF
11.0
22.0
41.5
37.5
1.0
100
2.2 µF
11.0
22.0
41.5
37.5
1.0
2.2 µF
13.0
24.0
41.5
37.5
1.0
3.3 µF
16.0
28.5
41.5
37.5
4.7 µF
16.0
28.5
41.5
4.7 µF
19.0
32.0
6.8 µF
20.0
10.0 µF
30.0
ENEC
IEC 60384-14
Class X2
File No.V4413
UL 1414
(up to 1µF, 85°C;
250Vac)
Across-the-line
File No.E97797
CSA - C22.2 No.1
(up to 1µF, 85°C;
250Vac)
Across-the-line
certified for
Canada
File No.E97797
UL 1283
(310 Vac)
Electromagnetic
Interference
Filters
File No.E85238
CSA - C22.2 No.8
(310 Vac)
Electromagnetic
Interference
Filters certified
for Canada
File No.E85238
GB/T 14472
Class X2
File CQC03001008199
CQC03001008842
Approved according to IEC 60384-14
According to IEC 60065
Not for use in series with the mains.
See
www.kemet.com for more information.
(**)ENEC mark has replaced all the following European National marks:
Table 1
Standard
packaging style
Lead
length
Taping style
Ordering
code
(Digit 10 to 11)
P2
(mm)
Fig.
(No.)
Pitch
(mm)
AMMO-PACK
AMMO-PACK
12.70
19.05
1
2
10.0/15.0
22.5
DQ
DQ
-
REEL Ø500mm
-
REEL Ø500mm
12.70
19.05
1
2
10.0/15.0
22.5/27.5
CK
CK
R46 KR 4470 - - S2
-
R46 KW 4150 - - S1
-
100
R46 KW 4220 - - S2
M
Loose, short leads
Loose, long leads
Loose, long leads
100
R46 KW 4220 - - S1
-
1.0
100
R46 KW 4330 - - S1
-
37.5
1.0
100
R46 KW 4470 - - S2
M
41.5
37.5
1.0
100
R46 KW 4470 - - S1
-
40.0
41.5
37.5
1.0
100
R46 KW 4680 - - S2
-
45.0
41.5
37.5
1.0
100
R46 KW 5100 - - S1
-
(mm)
Loose, insulated
rigid leads
Loose, insulated
flexible leads
04 +2
25 -1/+2
30 +5
00
50
40
30 +5
51
150 ±5
52
Note: Ammo-pack is the preferred packaging for taped version.
Rated voltage (K=275Vac)
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
300Vac Available upon request
E12 Series available upon request
All dimensions are in mm
09/2008
Not for new design.
156
Loose
R.46+R
Capacitors with discharge resistor
X2 CLASS (IEC 60384-14) - MKP Series
Taped
Fig.1
Fig.2
metallized polyPROPYLENE film capacitor
SELF-HEALING PROPERTIES
Insulated rigid leads
Typical applications: interference suppression and
«across-the-line» applications. Suitable for use in situations
where failure of the capacitor would not lead to danger of
electric shock.
Insulated flexible leads 0.5mm2
PRODUCT CODE: R46
Ø d ±0.05
P= 22.5 to 27.5
p = 37.5
0.8
1
Pitch Box thickness (B)
(mm)
(mm)
Maximum dimensions (mm)
B max
H max
L max
22.5
27.5
37.5
B +0.2
B +0.2
B +0.3
All
All
All
Damp heat, steady state:
Test conditions 1st
GENERAL TECHNICAL DATA
Temperature:
Relative humidity (RH):
Test duration:
Dielectric: polypropylene film.
Performance
Plates: metal layer deposited by evaporation under vacuum.
Leads: tinned wire.
Protection: plastic case, thermosetting resin filled.
Box material is solvent resistant and flame retardant according to
UL94 V0.
Endurance:
Test conditions
Marking: Manufacturer’s logo, series, capacitance, tolerance,
rated voltage, capacitor class, dielectric code, climatic category,
passive flammability category, manufacturing date code, approvals,
manufacturing plant.
Temperature:
Test duration:
Voltage applied:
Dielectric strength: no dielectric breakdown or
flashover at 4.3 x VR (d.c.)/1 min
Capacitance change |∆C/C|:≤10%
Insulation resistance: ≥50% of initial limit.
Operating temperature range: -40 to +110°C
IEC 60384-14, EN 60384-14.
electrical characteristics
Capacitance range:
Resistance to soldering heat:
Test conditions
Solder bath temperature: +260°C ± 5°C
Dipping time (with heat screen):10 s ± 1 s
0.22µF to 10µF
Capacitance values: E6 series (IEC 60063 Norm).
Performance
Capacitance tolerances (measured at 1 kHz):
±10% (K); ±20% (M).
Dissipation factor (DF):
tgδ 10-4 at +25°C ±5°C:
Typical value
≤10 (6)* at 1kHz *
Capacitance change |∆C/C|:≤2%
APPROVALS
Insulation resistance:
Test conditions
Temperature:
Voltage charge time:
Voltage charge:
+25°C±5°C
1 min
100 Vdc
Performance
≥1x105 MΩ (5x105 MΩ )*
≥30000 s (150000 s )*
for C≤0.33µF
for C>0.33µF
* Typical value
Test voltage between terminations (on all pieces):
+110°C ± 2°C
1000 h
1.25 x VR +1000Vac 0.1 s/h
Performance
Climatic category: 40/110/56 IEC 60068-1
275Vac (50/60Hz) / 560 Vdc
300Vac (50/60Hz) / 630 Vdc
+40°C ± 2°C
93% ±2%
56 days
Dielectric strength: no dielectric breakdown or flashover at 4.3 x VR (d.c.)/1 min
Capacitance change |∆C/C|:≤5%
Insulation resistance: ≥50% of initial limit.
Winding: non-inductive type.
Rated voltage (VR):
L +0.3
L +0.3
L +0.3
test method and performance
All dimensions are in mm.
Related documents:
H +0.1
H +0.1
H +0.1
ENEC
IEC 60384-14
Class X2
UL 1283
(310Vac-105°C)
Electromagnetic
Interference
File No.E85238
Filters
CSA - C22.2 No.8
(310Vac-105°C)
Electromagnetic
Interference
File No.E85238
Filters certified
for Canada
File No.V4413
Approved according to IEC 60384-14
According to IEC 60065.
Not for use in series with the mains.
See www.kemet.com for more information.
157
09/2008
R.46+R
Capacitors with discharge resistor
X2 CLASS (IEC 60384-14) - MKP Series
metallized polyPROPYLENE film capacitor
SELF-HEALING PROPERTIES
PRODUCT CODE: R46
Not for use in series with the mains.
See www.kemet.com for more information.
Rated
Cap. (*)
275 Vac / 560 Vdc
Std dimensions
B
H
L
Ød
Max
dv/dt at
390Vdc
(V/ µs)
Part Number
p
Table 1
Standard
packaging style
0.22 µF
7.0 16.0 26.5 22.5
0.8
200
R46KN 3220 - - 01 - x
0.33 µF
8.5 17.0 26.5 22.5
0.8
200
R46KN 3330 - - 01 - x
REEL Ø500mm
0.8
200
R46KN 3470 - - 01 - x
0.68 µF 11.0 20.0 26.5 22.5
0.8
200
R46KN 3680 - - 01 - x
Loose, short leads
Loose, long leads
Loose, long leads
0.8
150
R46KR 3470 - - 01 - x
0.68 µF 11.0 20.0 32.0 27.5
0.8
150
R46KR 3680 - - M1- x
1.0 µF 13.0 22.0 32.0 27.5
0.8
150
R46KR 4100 - - M1- x
1.5 µF 13.0 22.0 32.0 27.5
0.8
150
R46KR 4150 - - M1- x
2.2 µF 14.0 28.0 32.0 27.5
0.8
150
R46KR 4220 - - M1- x
3.3 µF 18.0 33.0 32.0 27.5
0.8
150
R46KR 4330 - - M2- x
4.7 µF 22.0 37.0 32.0 27.5
0.8
150
R46KR 4470 - - M1- x
Loose, insulated
rigid leads
Loose, insulated
flexible leads
1.0
100
R46KW 4150 - - M1- x
1
1.0
100
R46KW 4220 - - M1 - x
3.3 µF 16.0 28.5 41.5 37.5
1.0
100
R46KW 4330 - - M1 - x
R 4 6
4.7 µF 19.0 32.0 41.5 37.5
1.0
100
R46KW 4470 - - M1- x
6.8 µF 20.0 40.0 41.5 37.5
1.0
100
R46KW 4680 - - M2- x
10.0 µF 24.0 44.0 41.5 37.5
1.0
100
R46KW 5100 - - M1- x
300 Vac / 630 Vdc
Std dimensions
B
H
L
Ød
Max
dv/dt at
390Vdc
(V/ µs)
Part Number
p
0.22 µF
7.0 16.0 26.5 22.5
0.8
200
R463N 3220 - - 01 - x
0.33 µF
8.5 17.0 26.5 22.5
0.8
200
R463N 3330 - - 01 - x
0.47 µF 10.0 18.5 26.5 22.5
0.8
200
R463N 3470 - - 01 - x
0.68 µF 11.0 20.0 26.5 22.5
0.8
200
R463N 3680 - - 01 - x
2
3
4
5
0.8
150
R463R 3470 - - 01 - x
0.8
150
R463R 3680 - - M1- x
1.0 µF 13.0 22.0 32.0 27.5
0.8
150
R463R 4100 - - M1- x
1.5 µF 13.0 22.0 32.0 27.5
0.8
150
R463R 4150 - - M1- x
R
code (x)
2.2 µF 14.0 28.0 32.0 27.5
0.8
150
R463R 4220 - - M1- x
470 kΩ
E
3.3 µF 18.0 33.0 32.0 27.5
0.8
150
R463R 4330 - - M2- x
680 kΩ
F
4.7 µF 22.0 37.0 32.0 27.5
0.8
150
R463R 4470 - - M1- x
1 MΩ
G
1.5 µF 11.0 22.0 41.5 37.5
1.0
100
R463W 4150 - - M1- x
1.2 MΩ
L
2.2 µF 13.0 24.0 41.5 37.5
1.0
100
R463W 4220 - - M1 - x
1.5 MΩ
N
3.3 µF 16.0 28.5 41.5 37.5
1.0
100
R463W 4330 - - M1 - x
1.0
100
R463W 4470 - - M1- x
1.0
100
R463W 4680 - - M2- x
10.0 µF 24.0 44.0 41.5 37.5
1.0
100
R463W 5100 - - M1- x
Pitch
(mm)
19.05
2
22.5/27.5
CK
+2
04
25 -1/+2
30 +5
00
50
40
30 +5
51
150 ±5
52
6
7
8
9 10 11 12 13
14 15
-
Digit 1 to 3 Series code.
Digit 4 a.c. rated voltage:
K = 275Vac; 3 = 300Vac
Digit 5 Pitch:
N = 22.5;
R = 27.5;
W = 37.5 mm
Digit 6 to 9 Digits 7 - 8 - 9 indicate the first three digits of
Capacitance value and the 6th digit indicates
the number of zeros that must be added to
obtain the Rated Capacitance in pF.
Digit 10 to 11 Mechanical version and/or packaging (table 1)
Digit 12 Identifies the dimensions and electrical characteristics.
Digit 13 Internal use
Digit 14 Capacitance tolerance:
K=±10%; M=±20%
Digit 15 Value of the discharge resistor (tolerance±10%)
0.68 µF 11.0 20.0 32.0 27.5
6.8 µF 20.0 40.0 41.5 37.5
Fig.
(No.)
-
0.47 µF 11.0 20.0 32.0 27.5
4.7 µF 19.0 32.0 41.5 37.5
P2
(mm)
The part number, comprising 15 digits, is formed as follows:
1.5 µF 11.0 22.0 41.5 37.5
Rated
Cap. (*)
Ordering
code
(Digit 10 to 11)
Product code system
2.2 µF 13.0 24.0 41.5 37.5
Rated voltage (K=275Vac)
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
Value of discharge resistor (Table 2)
Taping style
(mm)
0.47 µF 10.0 18.5 26.5 22.5
0.47 µF 11.0 20.0 32.0 27.5
Lead
length
according to the following table*:
Table 2
2.2 MΩ
P
3.3 MΩ
Q
4.7 MΩ
S
6.8 MΩ
T
10 MΩ
V
*Other resistors are avaible upon
request.
Rated voltage (3=300Vac)
Mechanical version and packaging (Table 1)
Tolerance: K (±10%); M (±20%)
All dimensions are in mm
Value of discharge resistor (Table 2)
Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute –
and we specifically disclaim – any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who
have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained.