EEV Series, +105ºC

Surface Mount Aluminum Electrolytic Capacitors
EEV Series, +105ºC
Overview
Applications
KEMET's EEV Series of aluminum electrolytic surface mount
capacitors are designed for applications requiring ultra-low
impedance and a low profile vertical chip.
Typical applications include audio/visual (AV), computer/monitor,
communications, and switch mode power supplies (SMPS).
Benefits
•
•
•
•
Surface mount lead terminals
Low profile vertical chip
Ultra-low impedance
+105°C/2,000 hours
Part Number System
EEV
226
M
6R3
A
9B
AA
Series
Capacitance Code (pF)
Tolerance
Rated Voltage (VDC)
Electrical Parameters
Size Code
Packaging
Surface Mount
Aluminum
Electrolytic
Digits 4 – 5 represent
the first two digits of the
capacitance value. The
final digit indicates the
number of zeros to be
added.
M = ±20%
A = Standard
See Dimension Table
AA = Tape & Reel
6R3 = 6.3
010 = 10
016 = 16
025 = 25
035 = 35
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
1
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Dimensions – Millimeters
G
F
Size Code
9B
9D
9G
9H
9L
9M
9P
Size Code
9B
9D
9G
9H
9L
9M
9P
D
L
A/B
C
E
Nominal
Tolerance
Nominal
Tolerance
Nominal
Tolerance
Nominal
Tolerance
Nominal
Tolerance
4
5
6.3
6.3
8
8
10
±0.5
±0.5
±0.5
±0.5
±0.5
±0.5
±0.5
5.4
5.4
5.4
7.7
6.2
10.2
10.2
+0.25/-0.1
+0.25/-0.1
+0.25/-0.1
±0.3
±0.3
±0.3
±0.3
4.3
5.3
6.6
6.6
8.3
8.3
10.3
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
5.5
6.5
7.8
7.8
9.5
10
13
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
1.8
2.2
2.6
2.6
3.4
3.4
3.5
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
F
G
P
W
Nominal
Tolerance
Nominal
Tolerance
Nominal
Tolerance
Nominal
Tolerance
0.3
0.3
0.3
0.3
0.3
0.3
0.3
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
0.35
0.35
0.35
0.35
0.35
0.70
0.70
+0.15/-0.2
+0.15/-0.2
+0.15/-0.2
+0.15/-0.2
+0.15/-0.2
±0.2
±0.2
1.0
1.5
1.8
1.8
2.2
3.1
4.6
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
0.65
0.65
0.65
0.65
0.65
0.9
0.9
±0.1
±0.1
±0.1
±0.1
±0.1
±0.2
±0.2
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
2
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Performance Characteristics
Item
Performance Characteristics
Capacitance Range
Capacitance Tolerance
Rated Voltage
Life Test
Operating Temperature
4.7 – 1,500 µF
±20% at 120 Hz / 20°C
6.3 – 35 VDC
2,000 hours (see conditions in Test Method & Performance)
-40°C to +105°C
I ≤ 0.01 CV or 3 µA
Leakage Current
C = rated capacitance (µF), V = rated voltage (VDC). Voltage applied
for 2 minutes at 20°C.
Compensation Factor of Ripple Current (RC) vs. Frequency
Frequency
120 Hz
1 kHz
10 kHz
100 kHz
Coefficient
0.70
0.80
0.90
1.00
Test Method & Performance
Conditions
Load Life Test
Shelf Life Test
Temperature
105°C
105°C
Test Duration
2,000 hours
1,000 hours
Ripple Current
Maximum ripple current specified at 120 Hz 105°C
No ripple current applied
The sum of DC voltage and the peak AC voltage must
not exceed the rated voltage of the capacitor.
No voltage applied
Voltage
Performance
Capacitance Change
Dissipation Factor
Leakage Current
The following specifications will be satisfied when the capacitor is restored to 20°C:
Within ±20% of the initial value
Does not exceed 200% of the specified value
Does not exceed specified value
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
3
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Environmental Compliance
As an environmentally conscious company, KEMET is working continuously with improvements concerning the environmental effects
of both our capacitors and their production. In Europe (RoHS Directive) and in some other geographical areas like China, legislation
has been put in place to prevent the use of some hazardous materials, such as lead (Pb), in electronic equipment. All products in this
catalog are produced to help our customers’ obligations to guarantee their products and fulfill these legislative requirements. The only
material of concern in our products has been lead (Pb), which has been removed from all designs to fulfill the requirement of containing
less than 0.1% of lead in any homogeneous material. KEMET will closely follow any changes in legislation world wide and makes any
necessary changes in its products, whenever needed.
Some customer segments such as medical, military and automotive electronics may still require the use of lead in electrode coatings.
To clarify the situation and distinguish products from each other, a special symbol is used on the packaging labels for RoHS compatible
capacitors.
Because of customer requirements, there may appear additional markings such as LF = Lead Free or LFW = Lead Free Wires on the
label.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
4
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Table 1 – Ratings & Part Number Reference
VDC
VDC Surge
Voltage
Rated
Capacitance
120 Hz 20°C (µF)
Case Size
D x L (mm)
DF
120 Hz 20°C
(tan δ %)
RC
100 kHz
105°C (mA)
Z
100 kHz
20°C (Ω)
Part Number
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
10
10
10
10
10
10
10
10
10
10
10
10
16
16
16
16
16
16
16
16
16
16
16
16
16
25
25
25
25
25
25
25
25
25
25
25
35
35
35
35
35
35
35
35
35
35
35
35
8
8
8
8
8
8
8
8
8
8
8
8
8
8
13
13
13
13
13
13
13
13
13
13
13
13
20
20
20
20
20
20
20
20
20
20
20
20
20
32
32
32
32
32
32
32
32
32
32
32
44
44
44
44
44
44
44
44
44
44
44
44
22
33
47
47
100
100
150
220
330
330
470
680
1000
1500
22
33
33
47
100
150
220
220
330
470
470
1000
22
22
33
47
47
100
150
340
340
220
330
470
470
10
22
33
33
47
68
100
150
220
330
470
3.3
10
10
22
33
47
68
100
100
150
220
330
4 x 5.4
4 x 5.4
4 x 5.4
5 x 5.4
5 x 5.4
6.3 x 5.4
6.3 x 7.7
6.3 x 7.7
6.3 x 7.7
8 x 6.2
8 x 10.2
8 x 10.2
8 x 10.2
10 x 10.2
4 x 5.4
4 x 5.4
5 x 5.4
6.3 x 5.4
6.3 x 5.4
6.3 x 7.7
6.3 x 7.7
8 x 6.2
8 x 10.2
8 x 10.2
10 x 10.2
10 x 10.2
4 x 5.4
5 x 5.4
5 x 5.4
5 x 5.4
6.3 x 5.4
6.3 x 5.4
6.3 x 7.7
6.3 x 7.7
8 x 6.2
8 x 10.2
8 x 10.2
8 x 10.2
10 x 10.2
4 x 5.4
5 x 5.4
5 x 5.4
6.3 x 5.4
6.3 x 5.4
6.3 x 5.4
6.3 x 7.7
8 x 10.2
8 x 10.2
10 x 10.2
10 x 10.2
4 x 5.4
4 x 5.4
5 x 5.4
5 x 5.4
6.3 x 5.4
6.3 x 5.4
6.3 x 7.7
6.3 x 7.7
8 x 10.2
8 x 10.2
8 x 10.2
10 x 10.2
26
26
26
26
26
26
26
26
26
26
26
26
26
26
19
19
19
19
19
19
19
19
19
19
19
19
16
16
16
16
16
16
16
16
16
16
16
16
16
14
14
14
14
14
14
14
14
14
14
14
12
12
12
12
12
12
12
12
12
12
12
12
90
90
90
160
160
240
240
240
280
300
600
600
600
850
90
90
160
190
190
240
280
300
600
600
600
850
90
160
160
160
240
240
280
280
280
370
600
600
850
90
160
160
240
240
240
280
600
600
600
850
90
90
160
160
240
240
280
280
600
600
600
850
1.93
1.93
1.93
1.00
1.00
0.52
0.30
0.30
0.34
0.26
0.16
0.16
0.16
0.08
1.93
1.93
1.00
0.52
0.52
0.34
0.34
0.26
0.16
0.16
0.12
0.08
1.93
1.00
1.00
1.00
0.52
0.52
0.34
0.22
0.22
0.22
0.16
0.16
0.08
1.93
1.00
1.00
0.52
0.52
0.52
0.34
0.16
0.16
0.16
0.08
1.93
1.93
1.00
1.00
0.52
0.52
0.34
0.34
0.16
0.16
0.16
0.08
EEV226M6R3A9BAA
EEV336M6R3A9BAA
EEV476M6R3A9BAA
EEV476M6R3A9DAA
EEV107M6R3A9DAA
EEV107M6R3A9GAA
EEV157M6R3A9HAA
EEV227M6R3A9HAA
EEV337M6R3A9HAA
EEV337M6R3A9LAA
EEV477M6R3A9MAA
EEV687M6R3A9MAA
EEV108M6R3A9MAA
EEV158M6R3A9PAA
EEV226M010A9BAA
EEV336M010A9BAA
EEV336M010A9DAA
EEV476M010A9GAA
EEV107M010A9GAA
EEV157M010A9HAA
EEV227M010A9HAA
EEV227M010A9LAA
EEV337M010A9MAA
EEV477M010A9MAA
EEV477M010A9PAA
EEV108M010A9PAA
EEV226M016A9BAA
EEV226M016A9DAA
EEV336M016A9DAA
EEV476M016A9DAA
EEV476M016A9GAA
EEV107M016A9GAA
EEV157M016A9HAA
EEV227M016A9HAA
EEV227M016A9LAA
EEV227M016A9MAA
EEV337M016A9MAA
EEV477M016A9MAA
EEV687M016A9PAA
EEV106M025A9BAA
EEV226M025A9DAA
EEV336M025A9DAA
EEV336M025A9GAA
EEV476M025A9GAA
EEV686M025A9GAA
EEV107M025A9HAA
EEV157M025A9MAA
EEV227M025A9MAA
EEV337M025A9PAA
EEV477M025A9PAA
EEV335M035A9BAA
EEV106M035A9BAA
EEV106M035A9DAA
EEV226M035A9DAA
EEV336M035A9GAA
EEV476M035A9GAA
EEV686M035A9HAA
EEV107M035A9HAA
EEV107M035A9MAA
EEV157M035A9MAA
EEV227M035A9PAA
EEV337M035A9PAA
VDC
VDC Surge
Rated Capacitance
Case Size
DF
RC
Z
Part Number
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
5
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Mounting Positions (Safety Vent)
In operation, electrolytic capacitors will always conduct a leakage current which causes electrolysis. The oxygen produced by
electrolysis will regenerate the dielectric layer but, at the same time, the hydrogen released may cause the internal pressure of the
capacitor to increase. The overpressure vent (safety vent) ensures that the gas can escape when the pressure reaches a certain value.
All mounting positions must allow the safety vent to work properly.
Installing
• A general principle is that lower-use temperatures result in a longer, useful life of the capacitor. For this reason, it should be
ensured that electrolytic capacitors are placed away from heat-emitting components. Adequate space should be allowed between
components for cooling air to circulate, particularly when high ripple current loads are applied. In any case, the maximum category
temperature must not be exceeded.
• Do not deform the case of capacitors or use capacitors with a deformed case.
• Verify the correct polarization of the capacitor on the board.
It is recommended that capacitors always be mounted with the safety device uppermost or in the upper part of the capacitor.
• If the capacitors are stored for a long time, the leakage current must be verified. If the leakage current is superior to the value listed in
this catalog, the capacitors must be reformed. In this case, they can be reformed by application of the rated voltage through a series
resistor approximately 1 kΩ for capacitors with VR ≤ 160 V (5 W resistor) .
• In the case of capacitors connected in series, a suitable voltage sharing must be used.
In the case of balancing resistors, the approximate resistance value can be calculated as: R = 60/C
KEMET recommends, nevertheless, to ensure that the voltage across each capacitor does not exceed its rated voltage.
Application and Operation Guidelines
Electrical Ratings:
Capacitance (ESC)
Capacitance is measured by applying an alternate voltage of ≤ 0.5 V at a frequency of 120 or 100 Hz and 20°C.
Temperature Dependence of the Capacitance
Capacitance of an electrolytic capacitor depends upon temperature: with decreasing temperature the viscosity of the electrolyte
increases, thereby reducing its conductivity.
Capacitance will decrease if temperature decreases. Furthermore, temperature drifts cause armature dilatation and, therefore,
capacitance changes (up to 20% depending on the series considered, from 0 to 80°C). This phenomenon is more evident for
electrolytic capacitors than for other types.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
6
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Frequency Dependence of the Capacitance
Effective capacitance value is derived from the impedance curve, as long as impedance is still in the range where the capacitance
component is dominant.
1
2π fZ
C=
C = Capacitance (F)
f = Frequency (Hz)
Z = Impedance (Ω)
Dissipation Factor tan δ (DF)
Dissipation Factor tan δ is the ratio between the active and reactive power for a sinusoidal waveform voltage. It can be thought of as a
measurement of the gap between an actual and ideal capacitor.
reactive
δ
ideal
actual
active
Tan δ is measured with the same set-up used for the series capacitance ESC.
tan δ = ω x ESC x ESR where:
ESC = Equivalent Series Capacitance
ESR = Equivalent Series Resistance
Equivalent Series Inductance (ESL)
Self inductance or Equivalent Series Inductance results from the terminal configuration and internal design of the capacitor.
Capacitor Equivalent Internal Circuit
Equivalent
Series
Capacitance
(ESC)
Equivalent
Series
Resistance
(ESR)
Equivalent
Series
Inductance
(ESL)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
7
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Co
L
Re
Equivalent Series Resistance (ESR)
Equivalent Series Resistance is the resistive component of the equivalent series circuit. ESR value depends on frequency and
temperature and is related to the tan δ by the following equation:
Ce
ESR =
tan δ
2πf ESC
ESR = Equivalent Series Resistance (Ω)
tan δ = Dissipation Factor
ESC = Equivalent Series Capacitance (F)
f = Frequency (Hz)
Tolerance limits of the rated capacitance must be taken into account when calculating this value.
Impedance (Z)
L
Re
Co
Impedance of an electrolytic capacitor results from a circuit formed by the following individual equivalent series components:
Co
Re
L
Ce
Ce
Co = Aluminum oxide capacitance (surface and thickness of the dielectric)
Re = Resistance of electrolyte and paper mixture (other resistances not depending on the frequency are not considered: tabs, plates,
etc.)
Ce = Electrolyte soaked paper capacitance
L = Inductive reactance of the capacitor winding and terminals
Impedance of an electrolytic capacitor is not a constant quantity that retains its value under all conditions; it changes depending on
frequency and temperature.
Impedance as a function of frequency (sinusoidal waveform) for a certain temperature can be represented as follows:
Z [ohm]
1000
100
1/ω
ω Ce
10
B
Re
1
0.1
ωL
A
1/ω
ω Co
0.1
1
10
C
100
1000
10000
F [KHz]
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
8
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
• Capacitive reactance predominates at low frequencies
• With increasing frequency, capacitive reactance Xc = 1/ωCo decreases until it reaches the order of magnitude of electrolyte
resistance Re(A)
• At even higher frequencies, resistance of the electrolyte predominates: Z = Re (A - B)
• When the capacitor’s resonance frequency is reached (ω0), capacitive and inductive reactance mutually cancel each other
1/ωCe = ωL, ω0 = C√1/LCe
• Above this frequency, inductive reactance of the winding and its terminals (XL = Z = ωL) becomes effective and leads to an increase
in impedance
Generally speaking, it can be estimated that Ce ≈ 0.01 Co.
Impedance as a function of frequency (sinusoidal waveform) for different temperature values can be represented as follows (typical
values):
Z (oh m )
10 µF
1000
100
-4 0°C
10
2 0°C
8 5°C
1
0.1
0.1
1
10
100
1000
1 0 0 00
F (K HElectrolyte
z)
Re is the most temperature-dependent component of an electrolytic capacitor equivalent circuit.
resistivity will decrease if temperature rises.
In order to obtain a low impedance value throughout the temperature range, Re must be as little as possible. However, Re values
that are too low indicate a very aggressive electrolyte, resulting in a shorter life of the electrolytic capacitor at high temperatures. A
compromise must be reached.
Leakage Current (LC)
Due to the aluminum oxide layer that serves as a dielectric, a small current will continue to flow even after a DC voltage has been
applied for long periods. This current is called leakage current.
A high leakage current flows after applying voltage to the capacitor then decreases in a few minutes, e.g., after prolonged storage
without any applied voltage. In the course of continuous operation, the leakage current will decrease and reach an almost constant
value.
After a voltage-free storage the oxide layer may deteriorate, especially at high temperature. Since there are no leakage currents to
transport oxygen ions to the anode, the oxide layer is not regenerated. The result is that a higher than normal leakage current will flow
when voltage is applied after prolonged storage.
As the oxide layer is regenerated in use, the leakage current will gradually decrease to its normal level.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
9
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
The relationship between the leakage current and voltage applied at constant temperature can be shown schematically as follows:
I
VR
VS
VF
V
Where:
VF = Forming voltage
If this level is exceeded, a large quantity of heat and gas will be generated and the capacitor could be damaged.
VR = Rated voltage
This level represents the top of the linear part of the curve.
VS = Surge voltage
This lies between VR and VF. The capacitor can be subjected to VS for short periods only.
Electrolytic capacitors are subjected to a reforming process before acceptance testing. The purpose of this preconditioning is to ensure
that the same initial conditions are maintained when comparing different products.
Ripple Current (RC)
The maximum ripple current value depends on:
• Ambient temperature
• Surface area of the capacitor (heat dissipation area)
tan δ or ESR
• Frequency
The capacitor’s life depends on the thermal stress.
Frequency Dependence of the Ripple Current
ESR and, thus, the tan δ depend on the frequency of the applied voltage. This indicates that the allowed ripple current is also a function
of the frequency.
Temperature Dependence of the Ripple Current
The data sheet specifies maximum ripple current at the upper category temperature for each capacitor.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
10
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Expected Life Calculation
Expected life depends on operating temperature according to the following formula: L = Lo x 2 (To-T)/10
Where:
L:
Expected life
Lo:
Load life at maximum permissible operating temperature
T:
Actual operating temperature
To:
Maximum permissible operating temperature
This formula is applicable between 40°C and To.
Packaging Quantities
Size Code
Diameter (mm)
Length (mm)
Reel Quantity
Box Quantity
(4 Reels per box)
9B
4
5
6.3
6.3
8
8
10
5.4
5.4
5.4
7.7
6.2
10.2
10.2
2000
1000
1000
1000
1000
500
500
20000
10000
10000
10000
10000
4000
4000
9D
9G
9H
9L
9M
9P
Standard Marking for Surface Mount Types
Capacitance
(µF)
Rated Voltage
(VDC)
Series
Indentification
Negative Polarity:
Black Row
100
X
50
Date Code
(YMM)
201
Note: 6.3 V rated voltage shall be marked as 6 V, but 6.3 V shall be assured.
•Series
• Rated voltage (VDC)
• Capacitance (µF)
• Negative polarity: black line
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
11
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Soldering Process
The soldering conditions should be within the specified conditions below:
Do not dip the capacitors body into the melted solder. Flux should only be applied to the capacitors terminals
Vapour heat transfer systems are not recommended.
The system should be thermal, such as infra-red radiation or hot blast
Observe the soldering conditions as shown below.
Do not exceed these limits and avoid repeated reflowing
Reflow Soldering
T0
Pre-heat
T1
T2
T3
Lead Free Reflow Soldering
Temperature (°C)
Maximum Time
(Seconds)
20 to 140
140 to 180
180 to 140
> 200
230
60
150
100
60
20
Temperature (°C)
Maximum Time
(Seconds)
20 to 160
160 to 190
190 to 180
> 220
60
120
90
60
T0
Pre-heat
T1
T2
Size
T3
Φ4 ~ Φ5 (4 – 50 V)
Φ6.3 ~ Φ10 (4 – 50 V)
Φ4 ~ Φ10 (63 – 100 V)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Temperature Maximum Time
(°C)
(Seconds)
250
260
250
250
10
5
5
5
A4002_EEV • 12/9/2014
12
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Lead Taping & Packaging
Case Size (mm)
Reel
H
D
±0.2
4 x 5.4
5 x 5.4
6.3 x 5.4
6.3 x 7.7
8 x 6.2
8 x 10.2
10 x 10.2
W
±0.8
±1.0
21
21
21
21
21
21
21
14
14
18
18
18
26
26
380
D
H
W
Taping for Automatic Insertion Machines
Feeding hole
Chip pocket
Ø D0
P2
P0
E
t1
B
W
F
A
t2
P1
Tape running direction
Chip component
Dimensions (mm)
W
A
B
P0
P1
P2
F
D0
E
t1
t2
Tolerance
Nominal
Nominal
Nominal
±0.1
±0.1
±0.1
Nominal
±0.1
Nominal
Nominal
Nominal
4 x 5.4
5 x 5.4
6.3 x 5.4
6.3 x 7.7
8 x 6.2
8 x 10.2
10 x 10.2
12.5 x 13.5
12.5 x 16
16 x 16.5
12
12
16
16
16
24
24
32
32
44
4.7
5.7
7
7
8.7
8.7
10.7
13.4
13.4
17.5
4.7
5.7
7
7
8.7
8.7
10.7
13.4
13.4
17.5
4
4
4
4
4
4
4
4
4
4
8
12
12
12
12
16
16
24
24
28
2
2
2
2
2
2
2
2
2
2
5.5
5.5
7.5
7.5
7.5
11.5
11.5
14.2
14.2
20.2
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
1.75
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
5.8
5.8
5.8
5.8
6.8
11
11
14
17.5
17.5
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
13
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Construction
The manufacturing process begins with the anode foil being
electrochemically etched to increase the surface area and then
“formed” to produce the aluminum oxide layer. Both the anode and
cathode foils are then interleaved with absorbent paper and wound
into a cylinder. During the winding process, aluminum tabs are
attached to each foil to provide the electrical contact.
Extended cathode
Anode foil
The deck, complete with terminals, is attached to the tabs and then
folded down to rest on top of the winding. The complete winding
is impregnated with electrolyte before being housed in a suitable
container, usually an aluminum can, and sealed. Throughout the
process, all materials inside the housing must be maintained at the
highest purity and be compatible with the electrolyte.
Each capacitor is aged and tested before being sleeved and
packed. The purpose of aging is to repair any damage in the oxide
layer and thus reduce the leakage current to a very low level. Aging
is normally carried out at the rated temperature of the capacitor and
is accomplished by applying voltage to the device while carefully
controlling the supply current. The process may take several hours
to complete.
Damage to the oxide layer can occur due to variety of reasons:
• Slitting of the anode foil after forming
• Attaching the tabs to the anode foil
• Minor mechanical damage caused during winding
A sample from each batch is taken by the quality department after
completion of the production process.
The following tests are applied and may be varied at the request
of the customer. In this case the batch, or special procedure, will
determine the course of action.
Electrical:
• Leakage current
• Capacitance
• ESR
• Impedance
• Tan Delta
Mechanical/Visual:
• Overall dimensions
• Torque test of mounting stud
• Print detail
• Box labels
• Packaging, including packed
quantity
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Foil tabs
Tissues
Cathode foil
Etching
Forming
Winding
Decking
Impregnation
Assembly
Aging
Testing
Sleeving
Packing
A4002_EEV • 12/9/2014
14
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Paris, France
Tel:33-1-4646-1006
Northeast Asia
Hong Kong
Tel:852-2305-1168
MailingAddress:
P.O. Box 5928
Greenville, SC 29606
Sasso Marconi, Italy
Tel:39-051-939111
Shenzhen,China
Tel:86-755-2518-1306
www.kemet.com
Tel:864-963-6300
Fax:864-963-6521
Central Europe
Landsberg, Germany
Tel:49-8191-3350800
Corporate Offices
Fort Lauderdale, FL
Tel:954-766-2800
Kamen, Germany
Tel:49-2307-438110
North America
Northern Europe
Bishop’sStortford,UnitedKingdom
Tel:44-1279-460122
2835 KEMET Way
Simpsonville, SC 29681
Southeast
Lake Mary, FL
Tel:407-855-8886
Espoo, Finland
Tel:358-9-5406-5000
Northeast
Wilmington, MA
Tel:978-658-1663
Beijing,China
Tel:86-10-5829-1711
Shanghai,China
Tel:86-21-6447-0707
Taipei, Taiwan
Tel:886-2-27528585
Southeast Asia
Singapore
Tel:65-6586-1900
Penang, Malaysia
Tel:60-4-6430200
Bangalore, India
Tel:91-806-53-76817
Central
Novi, MI
Tel:248-306-9353
West
Milpitas, CA
Tel:408-433-9950
Mexico
Guadalajara,Jalisco
Tel:52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
15
Surface Mount Aluminum Electrolytic Capacitors – EEV Series, +105ºC
Disclaimer
Allproductspecifications,statements,informationanddata(collectively,the“Information”)inthisdatasheetaresubjecttochange.Thecustomerisresponsibleforcheckingand
verifyingtheextenttowhichtheInformationcontainedinthispublicationisapplicabletoanorderatthetimetheorderisplaced.
AllInformationgivenhereinisbelievedtobeaccurateandreliable,butitispresentedwithoutguarantee,warranty,orresponsibilityofanykind,expressedorimplied.
StatementsofsuitabilityforcertainapplicationsarebasedonKEMETElectronicsCorporation’s(“KEMET”)knowledgeoftypicaloperatingconditionsforsuchapplications,butare
notintendedtoconstitute–andKEMETspecificallydisclaims–anywarrantyconcerningsuitabilityforaspecificcustomerapplicationoruse.TheInformationisintendedforuseonly
bycustomerswhohavetherequisiteexperienceandcapabilitytodeterminethecorrectproductsfortheirapplication.AnytechnicaladviceinferredfromthisInformationorotherwise
providedbyKEMETwithreferencetotheuseofKEMET’sproductsisgivengratis,andKEMETassumesnoobligationorliabilityfortheadvicegivenorresultsobtained.
AlthoughKEMETdesignsandmanufacturesitsproductstothemoststringentqualityandsafetystandards,giventhecurrentstateoftheart,isolatedcomponentfailuresmaystill
occur.Accordingly,customerapplicationswhichrequireahighdegreeofreliabilityorsafetyshouldemploysuitabledesignsorothersafeguards(suchasinstallationofprotective
circuitryorredundancies)inordertoensurethatthefailureofanelectricalcomponentdoesnotresultinariskofpersonalinjuryorpropertydamage.
Althoughallproduct–relatedwarnings,cautionsandnotesmustbeobserved,thecustomershouldnotassumethatallsafetymeasuresareindictedorthatothermeasuresmaynot
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
A4002_EEV • 12/9/2014
16