NHD-5.7-320240WFB-CTXI#-T-1 TFT (Thin-Film-Transistor) Color Liquid Crystal Display Module NHD5.7320240WFBCTXI#-1 T-1- Newhaven Display 5.7” Diagonal 320xRGBx240 pixels Model Built-in driver + Controller White LED backlight TFT 6:00 view, Wide Temp RoHS Compliant Touch Panel Newhaven Display International, Inc. 2511 Technology Drive, Suite 101 Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com [email protected] [email protected] Document Revision History Revision 0 1 2 3 4 5 6 7 8 9 10 11 Date 7/8/2009 7/29/2009 11/4/2009 3/26/2010 4/16/2010 6/21/2010 2/22/2011 5/24/2011 1/6/2012 1/9/2012 6/4/2012 6/8/2012 Description Initial Release MECHANICAL DRAWING UPDATE Quality Information Update Pin description Update Updated the Recommended LCD Connector Touch Panel Pin Description Update Symbols for pin desc./electrical updated Electrical characteristics updated Pixel data format updated Touch panel pin description updated Mechanical drawing \ Optical characteristics updated Optical characteristics updated Functions and Features 320xRGBx240 resolution LED backlight 8-bit parallel interface SSD1963 Controller 4-Wire resistive Touch Panel [2] Changed by CL CL BE MP MC MP BE AK AK AK AK TJ Mechanical Drawing 1 2 3 4 Rev 5 6 Date 149.0±0.5 152.0±0.2 4.0 7.0 115.20±0.2(TFT_AA) 15.3 7.3 6.2 6.3 138.7±0.5 118.28±0.2(TFT_VA) 13.76 4.0 A 25.2 7.4 A 4-O3.5 PTH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 43.5 (320*3)*240 Dots 94.4 86.40±0.2(TFT_AA) 101.0±0.2 88.6±0.2(TFT_VA) CON2 CN-FPC-20P/P1.0 (Down-Side) 200.0±10.0 C 1 7.0±0.5 11.5Max 3 9.43 109.0±0.5 B NC RS WR RD DB2 DB3 DB4 DB5 DB6 DB7 CS RST Date Unit Gen. Tolerance ±0.3mm 2 C NC RL UD NC 06/04/12 1 B DB0 DB1 D 1.0 D GND VCC 3 4 [3] mm 5 Model: NHD-5.7-320240WFB-CTXI#-T-1 6 1 2 3 4 5 Rev 6 Date 78.0(PCB) (38.9) 55.7 A (22.4) A B B 70.0(PCB) 48.6 CN-FPC-50P/P0.5 (Up-Side) CN-FPC-20P/P1.0 (Down-Side) C C D D Date 06/04/12 Unit Gen. Tolerance ±0.3mm 1 2 3 4 [4] mm 5 Model: NHD-5.7-320240WFB-CTXI#-T-1 6 1 2 3 4 Rev 5 Description 6 Date A A B B C C D D Date 06/04/12 Unit Gen. Tolerance ±0.3mm 1 2 3 4 [5] mm 5 Model: NHD-5.7-320240WFB-CTXI#-T-1 6 Pin Description CON2: Pin No. 1 2 3 4 5 6 7-14 15 16 17 18 19 20 Symbol GND VDD NC D/C# WR# RD# [DB0-DB7] CS# RES# NC R/L U/D NC External Connection Power Supply Power Supply MPU MPU MPU MPU MPU MPU - Function Description Ground Power supply for LCD and logic (3.3V) No Connect Register Select signal: 1=Data, 0= Command Active LOW Write signal, 8080 MPU interface Active LOW Read signal, 8080 MPU interface Bi-directional data bus lines Active LOW Chip Select signal Active LOW Reset signal No Connect Scan direction 1: Right (Tied internally) Scan direction 0: Down (Tied internally) No Connect Recommended LCD connector: 1.0mm pitch 20-Conductor FFC. Molex 52271-2079 Backlight connector: JST p/n: XHP-3 Mates with: JST p/n: S3B-XH-SM3-TB Backlight: Pin No. Symbol 1 2 3 VDD NC GND External Connection Power Supply Power Supply Function Description Red, LED Anode (140mA @ 9.9V) No Connect White, LED Cathode Backlight connector: JST p/n: XHP-3 Mates with: JST p/n: B 3B-XH-A Touch Panel: Pin No. 1 2 3 4 Symbol XX+ YY+ External Connection Touch Controller Touch Controller Touch Controller Touch Controller Function Description RIGHT LEFT BOTTOM TOP Recommended Touch panel connector: 2.54mm pitch Standard Pin Headers [6] Controller Information Built-in SSD1963 controller. Please download specification at http://www.newhavendisplay.com/app_notes/SSD1963.pdf 8080 Mode Interface: The 8080 mode MPU interface consists of CS#, D/C, RD#, WR#, and DB[7:0]. This interface uses WR# to define a write cycle and RD# to define a read cycle. If the WR# goes LOW when the CS# signal is LOW, the data or command will be latched into the system at the rising edge of WR#. Similarly, the read cycle will start when RD# goes LOW and end at the rising edge of RD#. See the SSD1963 datasheet for detailed timing diagrams. Command Instructions: See the SSD1963 datasheet for the Instruction Table and Command Descriptions. Pixel Data Format: [7] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current “H” Level Input “L” Level Input Backlight Supply Voltage Backlight Supply Current Backlight Lifetime Symbol Top Tst VDD IDD VIH VIL VLED ILED Condition Absolute Max Absolute Max VDD=3.3 VLED=9.4V Min. -20 -30 3.0 0.8*VDD 0 Typ. 3.3 121 - Max. +70 +80 3.5 VDD 0.2*VDD Unit ⁰C ⁰C V mA V V 9.0 - 9.9 140 50,000 10.5 210 - V mA Hr Min. 40 60 60 60 300 - Typ. 60 70 70 70 250 15 35 Max. - Unit ⁰ ⁰ ⁰ ⁰ Typ. Max. 1.5 1000 650 Optical Characteristics Item Viewing Angle – Top (Note 1) Viewing Angle – Bottom (Note 1) Viewing Angle – Left Viewing Angle – Right Contrast Ratio Luminance Response Time (rise) Response Time (fall) Symbol Condition Cr ≥ 5 Cr ≥ 5 Cr ≥ 5 Cr ≥ 5 Cr YL Tr Tf 2 cd/m ms ms Note 1: Viewing direction – 12:00; Gray Scale inversion direction – 6:00. Touch Panel Characteristics Item Linearity Circuit Resistance – X-Axis Circuit Resistance – Y-Axis Insulation Resistance Operating Voltage Chattering Transmittance Activation Force Pen Writing Durability Pitting Durability Surface Hardness Haze Symbol Condition Min. 350 200 20 5 15 80 80 10,000 1,200,000 2 7 [8] Unit % Ω Ω MΩ V Ms % g Characters Touches H % Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Operation Thermal Shock resistance Vibration test Static electricity test Test Condition Endurance test applying electric static discharge. 2 -30⁰C , 240hrs 1,2 +70⁰C 240hrs 2 -20⁰C , 240hrs 1,2 +60⁰C , 90% RH , 240hrs 1,2 -20⁰C,30min -> 25⁰C,5min -> 70⁰C,30min = 1 cycle 10 cycles 10-55Hz , 15mm amplitude. 60 sec in each of 3 directions X,Y,Z For 15 minutes VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [9] Note +80⁰C , 240hrs 3