DC-DC Converter SIP-Package DAE-1H SERIES, 1WATT, 6KVDC, UNREGULATED FEATURES: 6000Vdc isolation voltage Low isolation capacitance Operating temperature range -40 3 year warranty Model Input voltage (Vdc) ℃ to +85 ℃ Output voltage (Vdc) Output current (mA) Min. Max. Efficiency Typ. DAE1-0511H 5 20 200 80% DAE1-0512H 9 11 110 80% DAE1-0513H 12 8.3 83 80% DAE1-0514H 15 6.8 68 80% 24 4.2 42 80% 10 100 80% 5.5 55 80% 4 40 80% 3.3 33 80% DAE1-0525H ±5 ±9 ±12 ±15 ±24 2.1 21 80% DAE1-1211H 5 20 200 80% DAE1-1212H 9 11 110 80% DAE1-1213H 12 8.3 83 80% DAE1-1214H 15 6.8 68 80% 24 4.2 42 80% ±5 ±9 ±12 ±15 ±24 10 100 80% 5.5 55 80% 4 40 80% 3.3 33 80% 2.1 21 80% DAE1-0515H DAE1-0521H 5(4.5~5.5) DAE1-0522H DAE1-0523H DAE1-0524H DAE1-1215H DAE1-1221H 12(10.8~13.2) DAE1-1222H DAE1-1223H DAE1-1224H DAE1-1225H Notes: 1. other input and output models may available on request; 2. Add suffix “P” for short circuit protection. ELECTRICAL Line regulation --- Load regulation 10% ~ 100% full load Ripple and noise --- 200mVp-p max. Isolation voltage --- 6000Vdc Operating temperature range --- -40℃ to +85℃ www.pairuigroup.com ±1.2% Page: 1/3 15% max. Date: 09/19/2014 DC-DC Converter SIP-Package DAE-1H SERIES, 1WATT, 6KVDC, UNREGULATED ELECTRICAL MTBF --- 3500KHrs Weight --- 2.7g Notes: All the parameters are measured at 25℃ ambient temperature, humidity < 75%, nominal input voltage, full load and after warm-up, unless otherwise specified. MECHANICAL CONNECTION PIN # SINGLE DUAL 1 +Vin +Vin 2 GND GND 5 -Vo -Vo 6 No Pin COM 7 +Vo +Vo Note: * Unit is mm(inch). TEMPERATURE PROFILE CAPACITIVE LOADS SELECTION Single Output Cin (Vdc) (μF) 5 4.7 5 10 ±5 4.7 12 2.2 9 4.7 ±9 2.2 24 1 12 2.2 ±12 1 - - 15/24 1 ±15 0.47 www.pairuigroup.com Voltage Cout Dual Output Vin (μF) (Vdc) Page: 2/3 Voltage (Vdc) Cout (μF) Date: 09/19/2014 DC-DC Converter SIP-Package DAE-1H SERIES, 1WATT, 6KVDC, UNREGULATED NOTES RECOMMENDED TEST AND APPLICATION CIRCUIT In order to ensure the efficiency and dependability of the module, the minimum specified load must be less than 10% of rated load. If the output power is low, we recommend to add an external 10% loading resistor in parallel. FUSE: depends on the actual input current; TVS: depends on the actual input voltage; Recommended capacitor: C1, C2, C5, about 0.1uF; for C6, C7, please check the capacitive load; C3,C4: 2KV/1nF. www.pairuigroup.com Page: 3/3 Date: 09/19/2014