DC-DC Converter DIP-Package DAN-2 SERIES, 2WATT, 1.5KVDC, ISOLATED, REGULATED FEATURES: 1500Vdc isolation voltage Single output models Low ripple & noise Operating temperature range -40 3 year warranty Model DAN2-0511 DAN2-0512 DAN2-0513 DAN2-0514 DAN2-0515 DAN2-1211 DAN2-1212 DAN2-1213 DAN2-1214 DAN2-1215 DAN2-1511 DAN2-1512 DAN2-1513 DAN2-1514 DAN2-1515 DAN2-2411 DAN2-2412 DAN2-2413 DAN2-2414 DAN2-2415 Input voltage (Vdc) ℃ to +85 ℃ Output voltage (Vdc) 5(4.75~5.25) 12(11.4~12.6) 15(13.5~16.5) 24(22.8~25.2) Output current (mA) Efficiency Typ. Min. Max. 5 40 400 69% 9 22.2 222 69% 12 16.7 167 75% 15 13.3 133 65% 24 8.3 83 65% 5 40 400 69% 9 22.2 222 66% 12 16.7 167 75% 15 13.3 133 72% 24 8.3 83 72% 5 40 400 67% 9 22.2 222 70% 12 16.7 167 70% 15 13.3 133 68% 24 8.3 83 72% 5 40 400 72% 9 22.2 222 75% 12 16.7 167 72% 15 13.3 133 70% 24 8.3 83 71% Notes: Other input and output models may available on request. ELECTRICAL ±3% max Output voltage accuracy --- Line regulation --- Load regulation 10% ~ 100% full load Isolation voltage Leakage current < 1mA/1min. 1500Vdc min. Isolation resistance Test at 500VDC 1000m Switching frequency --- Ripple & noise Bend width 20MHz www.pairuigroup.com ±0.5% max. ±1.5% max. Ω min. 100KHz typ. Page: 1/3 75mVp-p max. Date: 07/20/2015 * Subject to change without prior notice DC-DC Converter DIP-Package DAN-2 SERIES, 2WATT, 1.5KVDC, ISOLATED, REGULATED ELECTRICAL Temperature coefficient Rated load Operating temperature range --- Storage temperature range --- ±0.03%/℃ -40℃ to +85℃ -55℃ to +125℃ Short circuit protection --- 1S MTBF --- 3500KHrs Weight --- 2.8g Notes: All the parameters are measured at 25℃ ambient temperature, humidity < 75%, nominal input voltage, full load and after warm-up, unless otherwise specified. MECHANICAL CONNECTION PIN # SINGLE 1 GND 7 NC 8 No Pin 9 +Vo 10 No Pin 11 0V 14 +Vin Note: * Unit is mm(inch). ELECTRICAL CURVE www.pairuigroup.com Page: 2/3 Date: 07/20/2015 * Subject to change without prior notice DC-DC Converter DIP-Package DAN-2 SERIES, 2WATT, 1.5KVDC, ISOLATED, REGULATED NOTE RECOMMENDED TEST AND APPLICATION CIRCUIT CAPACITOR SELECTION INPUT VOLTAGE C1 OUTPUT VOLTAGE C2 5VDC 4.7μF 5VDC 4.7μF 12VDC 2.2μF 9VDC 4.7μF 15VDC 1.0μF 12VDC 2.2μF 24VDC 0.47μF 15VDC 1.0μF -- -- 24VDC 0.47μF www.pairuigroup.com Page: 3/3 Date: 07/20/2015 * Subject to change without prior notice