NJG1608KB2 SPDT SWITCH GaAs MMIC

NJG1608KB2
SPDT SWITCH GaAs MMIC
! GENERAL DESCRIPTION
The NJG1608KB2 is a SPDT switch IC featured low
insertion loss, medium handling power and high isolation.
The NJG1608KB2 is suitable for switching of Tx/Rx
signals at sub-microwave applications. The NJG1608KB2
exhibits wide frequency range from 100MHz to 6.0GHz at
low operating voltage of 2.5V, and is operated up to 25dBm
at 3.0V operating voltage.
The Pb free FLP6-B2 package is applied.
! FEATURES
"Single low voltage control
"Low insertion loss
"High isolation
"Handling power
"Ultra-small and ultra-thin package
! PACKAGE OUTLINE
NJG1608KB2
+2.5~+6.5V
0.30dB typ.
@f=2.0GHz
0.35dB typ.
@f=2.5GHz
0.60dB typ.
@f=5.85GHz
29dB typ.
@f=2.0GHz
30dB typ.
@f=2.5GHz
18dB typ.
@f=5.85GHz
P-1dB=30dBm typ. @f=2.5GHz, VCTL=3.0V
FLP6-B2 (Package size: 2.0mmx2.1mmx0.75mm typ.)
! PIN CONFIGURATION
Orientation Mark
KB2 Type
Top view
1
Pin connection
6
2
5
3
4
1.P1
2.GND
3.P2
4.VCTL2
5.PC
6.VCTL1
! TRUTH TABLE
“H”=VCTL (H), “L”=VCTL (L)
Ver.2010--06-10
VCTL1
VCTL2
H
L
L
H
PC – P1
OFF
ON
PC – P2
ON
OFF
-1-
NJG1608KB2
! ABSOLUTE MAXIMUM RATINGS
(Ta=25°C, Zs=Zl=50Ω)
PARAMETER
SYMBOL
RATINGS
UNITS
VCTL (L)=0V, VCTL (H)=3.0V
32
dBm
VCTL
VCTL (H)-VCTL (L)
7.5
V
Power Dissipation
PD
on PCB board
550
mW
Operating Temp.
Topr
-40~+85
°C
Storage Temp.
Tstg
-55~+150
°C
Input Power
Control Voltage
Pin
CONDITIONS
! ELECTRICAL CHARACTERISTICS
(with application circuit, VCTL
PARAMETERS
SYMBOL
Operating voltage (LOW)
Operating voltage (HIGH)
(L)=0V,
CONDITIONS
VCTL
(H)=3.0V,
ZS=Zl=50Ω, Ta=25°C)
MIN
TYP
MAX
UNITS
VCTL (L)
-0.2
0
0.2
V
VCTL (H)
2.5
3.0
6.5
V
Control current
ICTL
f=2.0GHz
-
5
10
µA
Insertion loss 1
LOSS1
f=2.0GHz
-
0.30
0.45
dB
Insertion loss 2
LOSS2
f=2.5GHz
-
0.35
0.50
dB
Insertion loss 3
LOSS3
f=5.85GHz
0.60
0.80
dB
ISL1
f=2.0GHz,
26
29
-
dB
ISL2
f=2.5GHz,
27
30
-
dB
ISL3
f=5.85GHz
16
18
P-1dB(1)
f=2.5GHz
28
30
-
dBm
P-1dB(2)
f=5.85GHz
25
27
-
dBm
VSWR
f=0.1~5.85GHz, ON State
-
1.4
1.6
f=0.1~5.85GHz
-
100
-
Isolation 1
(PC-P1, PC-P2, P1-P2)
Isolation 2
(PC-P1, PC-P2, P1-P2)
Isolation 3
(PC-P1, PC-P2, P1-P2)
Input power at 1dB
compression point 1
Input power at 1dB
compression point 2
VSWR (PC, P1, P2)
Switching time
-2-
TSW
dB
ns
NJG1608KB2
! TERMINAL INFORMATION
No.
SYMBOL
1
P1
2
GND
3
P2
4
VCTL2
5
PC
6
VCTL1
DESCRIPTION
RF port. This port is connected with PC port by controlling 4th pin (VCTL(H))
to 2.5~6.5V and 6th pin(VCTL(L)) to -0.2~+0.2V. An external capacitor is
required to block the DC bias voltage of internal circuit
Ground terminal. Please connect this terminal with ground plane as close
as possible for excellent RF performance.
RF port. This port is connected with PC port by controlling 6th pin (VCTL (H))
to 2.5~6.5V and 4th pin(VCTL(L)) to -0.2~+0.2V. An external capacitor is
required to block the DC bias voltage of internal circuit.
Control port 2. The voltage of this port controls PC to P1 state. The ‘ON’
and ‘OFF’ state is toggled by controlling voltage of this terminal such as
high-state (2.5~6.5V) or low-state (-0.2~+0.2V). The voltage of 6th pin
have to be set to opposite state. The bypass capacitor has to be chosen
to reduce switching time delay from 10pF~1000pF range.
Common RF port. In order to block the DC bias voltage of internal circuit,
an external capacitor is required.
Control port 1. The voltage of this port controls PC to P2 state. The ‘ON’
and ‘OFF’ state is toggled by controlling voltage of this terminal such as
high-state (2.5~6.5V) or low-state (-0.2~+0.2V). The voltage of 4th pin
have to be set to opposite state. The bypass capacitor has to be chosen
to reduce switching time delay from 10pF~1000pF range.
-3-
NJG1608KB2
! ELECTRICAL CHARACTERISTICS
(0.1~6.0GHz, with application circuit, without DC Blocking Capacitor, Losses of external circuit are excluded.)
PC-P1 Insertion Loss vs. Frequency
PC-P2 Insertion Loss vs. Frequency
( VCTL1=0V, VCTL2=3V )
( VCTL1=3V, VCTL2=0V )
0.0
Insertion Loss (dB)
Insertion Loss (dB)
0.0
-0.5
-1.0
-1.5
-2.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
-0.5
-1.0
-1.5
-2.0
0.0
1.0
2.0
Frequency (GHz)
3.0
4.0
5.0
6.0
Frequency (GHz)
PC VSWR vs. Frequency
( PC-P1 ON, VCTL1=0V, VCTL2=3V )
2.0
VSWR
1.8
1.6
1.4
1.2
1.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
Frequency (GHz)
PC-P1 Isolation vs. Frequency
PC-P2 Isolation vs. Frequency
0
-5
-5
-10
-10
-15
-20
-25
-15
-20
-25
-30
-30
-35
-35
-40
0.0
1.0
2.0
3.0
4.0
Frequency (GHz)
-4-
( VCTL1=0V, VCTL2=3V )
0
Isolation (dB)
Isolation (dB)
( VCTL1=3V, VCTL2=0V )
5.0
6.0
-40
0.0
1.0
2.0
3.0
4.0
Frequency (GHz)
5.0
6.0
NJG1608KB2
! ELECTRICAL CHARACTERISTICS
PC-P1 Insertion Loss vs. Input Power
Control Current 2 vs. Input Power
( PC-P1 ON, f=2.5GHz, VCTL1=0V )
( f=2.5GHz, VCTL1=0V )
-0.2
25
Control Current 2 (μA)
Insertion Loss (dB)
-0.4
-0.6
-0.8
VCTL2=2V
VCTL2=2.5V
VCTL2=3V
VCTL2=3.5V
VCTL2=4.5V
VCTL2=5.5V
VCTL2=6.5V
-1.0
-1.2
-1.4
16
18
20
22
24
26
28
30
32
34
15
10
5
0
36
VCTL2=2V
VCTL2=2.5V
VCTL2=3V
VCTL2=3.5V
VCTL2=4.5V
VCTL2=5.5V
VCTL2=6.5V
20
16
18
20
Input Power (dBm)
22
24
26
28
30
32
34
36
Input Power (dBm)
PC-P1 Insertion Loss vs. Input Power
( f=5.85GHz, VCTL1=0V )
-0.4
Insertion Loss (dB)
-0.6
-0.8
-1.0
-1.2
VCTL2=2V
VCTL2=2.5V
-1.4
VCTL2=3V
-1.6
VCTL2=3.5V
VCTL2=6.5V
-1.8
10 12 14 16 18 20 22 24 26 28 30 32 34
Input Power (dBm)
2nd Harmonics vs. Input Power
3rd Harmonics vs. Input Power
( PC-P1 ON, f=2.5GHz, VCTL1=0V )
( PC-P1 ON, f=2.5GHz, VCTL1=0V )
-30
VCTL2=2V
VCTL2=2.5V
VCTL2=3V
VCTL2=3.5V
VCTL2=4.5V
VCTL2=5.5V
VCTL2=6.5V
Input 2fo
-60
-70
3rd Harmonics (dBc)
2nd Harmonics (dBc)
-50
-80
-90
-100
VCTL2=2V
VCTL2=2.5V
VCTL2=3V
VCTL2=3.5V
-40
VCTL2=4.5V
VCTL2=5.5V
VCTL2=6.5V
Input 3fo
-50
-60
-70
-80
14
16
18
20
22
24
26
28
30
Input Power (dBm)
32
34
36
-90
14
16
18
20
22
24
26
28
30
32
34
36
Input Power (dBm)
-5-
NJG1608KB2
! ELECTRICAL CHARACTERISTICS
90ns
VCTL2
P1
-6-
70ns
VCTL2
P1
NJG1608KB2
! APPLICATION CIRCUIT
VCTL1 (0V/3.0V)
Zo=50Ω
P1
1
6
2
5
C1
C5
Zo=50Ω
PC
C3
Zo=50Ω
3
P2
4
C2
C4
VCTL2 (3.0V/0V)
NJG1608KB2
Parts List
Parts number
List 1
List 2
List 3
Notes
C1~C3
C4, C5
100~500MHz
1000pF
10pF
0.5~2.0GHz
56pF
10pF
2.0~6.0GHz
16pF
10pF
GRM15 MURATA
GRM15 MURATA
! TEST PCB LAYOUT
(TOP VIEW)
C2
P2
C1
C4
C5
P1
PCB SIZE=19.4x14.0mm
PCB: FR-4, t=0.2mm
VCTL2
C3
PC
VCTL1
CAPACITOR: size 1005
STRIPLINE WIDTH=0.4mm
PRECAUTIONS
[1] The DC blocking capacitors have to be placed at RF terminal of P1, P2 and PC.
Please choose appropriate capacitance values to the application frequency.
[2] To reduce stripline influence on RF characteristics, please locate bypass
capacitors (C4, C5) close to each terminal.
[3] For good isolation, the GND terminal (2nd pin) must be placed possibly close to
ground plane of substrate, and through holes for GND should be placed near by
the pin connection.
-7-
NJG1608KB2
!PACKAGE OUTLINE (FLP6-B2)
0.75±0.05
2.0±0.1
+0.1
0.15-0.05
5
4
1
2
3
2.1±0.1
0.2
1.7±0.1
0.2
6
0.65
0.1
0.1
0.65
+0.1
0.2-0.05
Lead material
: Copper
Lead surface finish : Solder plating
Molding material : Epoxy resin
UNIT
: mm
Weight
: 6.5mg
Cautions on using this product
This product contains Gallium-Arsenide (GaAs) which is a harmful material.
• Do NOT eat or put into mouth.
• Do NOT dispose in fire or break up this product.
• Do NOT chemically make gas or powder with this product.
• To waste this product, please obey the relating law of your country.
This product may be damaged with electric static discharge (ESD) or spike voltage. Please
handle with care to avoid these damages.
-8-
[CAUTION]
The specifications on this databook are only
given for information , without any guarantee
as regards either mistakes or omissions. The
application circuits in this databook are
described only to show representative usages
of the product and not intended for the
guarantee or permission of any right including
the industrial rights.