P6AU-xxxxELF

P6AU-xxxxELF
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
PMA-SERIES
Rev.11-2008
1 Watt
Unregulated
Single Output
SIP4 Case
1 kV DC I/O Isolation
Low Ripple and Noise
The PMA series P6AU-xxxxELF is a family of cost effective 1 W single
output DC/DC converters. These converters are in an ultra miniature SIP4
case. Devices are encapsulated. High performance features: 1000VDC
input/output isolation, high efficiency operation, output voltage accuracy of
±3% maximum, input range of ±10% tolerance and low output ripple and
noise.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
± 10%
Capacitors
20 mA pk-pk
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (20% - 100%)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
± 3%
Short Term
± 1.2% / 1% Vin Change
± 10% (3.3Vout Models: ± 20%)
100 mV pk-pk
± 0.02% / °C
General Specifications
Efficiency
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
See Table
1000 VDC
60 pF, typ.
1000 MOhm
80 kHz (Variable)
95% rel H
> 1.121 Mhrs
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Epoxy (UL94V-0 rated)
~ 1.5g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85°C (ambient)
100°C
-40 to +125°C
Free Air Convection
Soldering 260°C, max. (1.5mm from case 10s.)
PMA-Series – P6AU-xxxxELF – Single Output – SIP4 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/3
Selection Guide
Single Output
A)
)
)
mA ad (mA
d (m
(
a
)
o
d
²
L
)
Loa
uF)
ll L o
VDC
DC
Full
)
ad (
t No rent Fu
ge (
e (V
ent
o
n
a
r
%
g
t
L
r
(
l
e
a
r
u
r
t
o
r
r
l
o
V
C
cy
t Cu put Cu
t Vo
acit
put
put
cien
Inpu
Inpu
In
Out
Out
Effi
Cap
Order #
SINGLE OUTPUT
P6AU-3R33R3ELF
P6AU-3R305ELF
P6AU-053R3ELF
P6AU-0505ELF
P6AU-057R2ELF
P6AU-0509ELF
P6AU-0512ELF
P6AU-0515ELF
P6AU-0518ELF
P6AU-0524ELF
P6AU-123R3ELF
P6AU-1205ELF
P6AU-127R2ELF
P6AU-1209ELF
P6AU-1212ELF
P6AU-1215ELF
P6AU-1218ELF
P6AU-1224ELF
P6AU-243R3ELF
P6AU-2405ELF
P6AU-247R2ELF
P6AU-2409ELF
P6AU-2412ELF
P6AU-2415ELF
P6AU-2418ELF
P6AU-2424ELF
P6AU-483R3ELF
P6AU-4805ELF
P6AU-487R2ELF
P6AU-4809ELF
P6AU-4812ELF
P6AU-4815ELF
P6AU-4818ELF
P6AU-4824ELF
3.3
3.3
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
25
30
25
25
25
25
25
25
25
25
16
16
16
16
16
16
16
16
10
10
10
10
10
10
10
10
7
7
7
7
7
7
7
7
452
415
278
267
264
260
257
257
257
257
116
112
110
109
107
107
107
107
58
56
55
55
54
54
54
54
29
28
27
27
27
27
27
27
3.3
5
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
303
200
303
200
138.8
111.1
83.3
66.67
55.5
41.67
303
200
138.8
111.1
83.3
66.67
55.5
41.67
303
200
138.8
111.1
83.3
66.67
55.5
41.67
303
200
138.8
111.1
83.3
66.67
55.5
41.67
67
73
72
75
76
77
78
78
78
78
72
75
76
77
78
78
78
78
72
75
76
77
78
78
78
78
72
75
76
76
76
76
76
76
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
If you need other specifications, please enquire.
PMA-Series – P6AU-xxxxELF – Single Output – SIP4 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/3
1.25
(0.05)
Package / Pinning / Derating
1
2
3
4
All dimensions are typical in millimeters (inches).
- Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002)
- Pin pitch tolerance: +/-0.35 (+/-0.014)
- Case tolerance +/-0.5 (+/-0.02)
Specification may change without notice.
Bottom View
0.50
(0.02)
9.65
(0.38)
11.68
(0.46)
6.00*
(0.24)*
PEAK
Modelcode
Datecode
2
3
4
0.50
(0.02)
1
* The thickness
of 48Vin voltage
is 7.50 (0.29)
3.05
(0.12)
0.25
(0.01)
0.50
(0.02)
2.54
(0.10)
0.50
(0.02)
SIP4 – PLASTIC CASE
PIN CONNECTIONS
#
SINGLE
1 - Vin
2 +Vin
3 - Vout
4 +Vout
App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH.
² = Tested by minimal Vin and constant resistive load.
- Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications.
- For reduce converter’s ripple & noise, it is recommended to add a 4.7µF~100µF capacitor in output end. For EMI performance
improvement, it is recommended to add a 12µH inductor and a 10µF~220µF capacitor in input end.
Radiated
Emissions
ESD
RS
EMC SPECIFICATIONS
EN 55022
CLASS B
FCC 47CFR Part 15/B
CLASS B
IEC 61000-4-2
Perf. Criteria B
IEC 61000-4-3
Perf. Criteria A
PMA-Series – P6AU-xxxxELF – Single Output – SIP4 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/3