LED-CONVERTER UNIT PS-LD0608-02(S) (150 W) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile LED-Converter is developed for max. 6 LED-lines APPLICABLE: 1~6 LED lines (Serial Mode) Pout max. 25 Watt per line, total max. 80 Watt LED Voltage max. 32V Lamp Current max. 700mAdc per line FEATURES : Internal Open LED Detection for every Line Analog dimming Remote ON / OFF RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH 0°C ~ +50°C -20°C ~ +85°C 95 %RH max 125 x 100 x 14.6 mm Weight :98 (g) typ. Components No. 1 2 Part Description PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) S12B-PH-SM3-TB Note t=1.6mm JST or equal 3 Connector CN2 1 S10B-PH-SM3-TB JST or equal Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0.3, 15th May 2014 LED-CONVERTER UNIT PS-LD0608-02(S) (150 W) (PRELIMINARY INFORMATION) Output side CN2: Input side CN1 Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 CN 1-6 CN 1-7 CN 1-8 CN 1-9 CN 1-10 CN 1-11 Symbols Ratings Vin 21.6 ~ 26.4 Vdc Vin 21.6 ~ 26.4 Vdc Vin 21.6 ~ 26.4 Vdc Vin 21.6 ~ 26.4 Vdc Vin 21.6 ~ 26.4 Vdc Vrmt 0 ~ 0.8 = OFF / 2.5 ~ Vin = ON Vbr 0.0 ~ 5.0 (5V=low brightness) GND GND GND GND GND CN 1-12 Pin No. CN2-1 CN2-2 CN2-3 CN2-4 CN2-5 CN2-6 CN2-7 CN2-8 CN2-9 Symbols Vhigh (+) Vhigh (+) Vhigh (+) Vhigh (+) RTN1 (-) RTN2 (-) RTN3 (-) RTN4 (-) RTN5 (-) Ratings max. 38Vdc max. 38Vdc max. 38Vdc max. 38Vdc LED LINE 1 RETURN LED LINE 2 RETURN LED LINE 3 RETURN LED LINE 4 RETURN LED LINE 5 RETURN CN2-10 RTN6 (-) LED LINE 6 RETURN - ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Open Load Shutdown Output Power Iout Imin Iin Vbias Pout Note 1 : Note 2 : Note 3 : Note 4 : Vin (V) Specification Vbr (V) Tu (°C) 21.6 ~ 26.4 21.6 ~ 26.4 21.6 ~ 26.4 21.6 ~ 26.4 21.6 ~ 26.4 0 5 0 0 0 0~+50 0~+50 0~+50 0~+50 0~+50 Min. Typ. Max. 630 25 1.0 43 700 35 45 770 45 9.0 49 80 Unit Note mAdc mAdc Adc Vdc Watt 100% Output voltage must always be 3.0Vdc higher than input voltage. The inrush current can be reduced by analog dimming. In case of not needing to connect all outputs please ask factory which pins to connect according to your needs. Pin temperature can be reduced when all the connector pins from both CN1 and CN2 are used. TEST CIRCUIT : Vin 10.8 ~ 13.2 Vdc Iin A CN1-1 V CN1-2 CN1-3 CN1-4 CN1-5 Vrmt 0.8 / 2.5 ~ Vin CN2-1 CN2-2 CN2-3 D1 D1 D2 D2 D6 D6 CN2-4 a V b SW1 Vbr 0 ~ 5.0 Vdc CN1-6 CN1-7 CN 2-5 A ~ CN 2-10 A ~ CN1-8 CN1-9 CN1-10 CN1-11 CN1-12 Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0.3, 15th May 2014