LED-CONVERTER UNIT PS-LD0301-038(S) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile LED-Converter is developed for max. 3 LED-lines Optimized for Optrex: T55465D065J-LW-A-AAN Optimized for Mitsubishi: AA065VD01 APPLICABLE: 1~3 LED lines (Serial Mode) Pout max. 7W LED Voltage max. 25Vdc Lamp Current max. 90mAdc FEATURES : Internal open LED detection for every line Voltage or ext. PWM dimming 1000:1 dimming ratio with external PWM Remote ON / OFF Wide input voltage range RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH -20°C ~ +70°C -20°C ~ +85°C 95 %RH max 64 x 32 x 6.5 mm Weight :8 (g) typ. Components No. 1 2 Part Description PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) 53261-0890 / PBD Note t=1.0mm Molex 3 Connector CN3 1 53261-0690 / PBD Molex Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0, 27th November 2009 LED-CONVERTER UNIT PS-LD0301-038(S) (PRELIMINARY INFORMATION) Output side CN3: Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 CN 1-6 CN 1-7 CN 1-8 Symbols Ratings Vin 4.75 ~ 13.2 Vdc Vin 4.75 ~ 13.2 Vdc Vrmt 0 ~ 1.5 = OFF / 2.5 ~ Vin = ON Ext. PWM 0 ~ 0.5 = LOW / 2.5 ~ 5 = HIGH Vbr 0.0 ~ 5.0 (5V=low brightness) GND GND GND Pin No. CN 3-1 CN 3-2 CN 3-3 CN 3-4 CN 3-5 Symbols RTN1(-) RTN2(-) N.C. N.C Vhigh(+) Ratings LED LINE 1 RETURN LED LINE 2 RETURN CN 3-6 Vhigh(+) 25Vdc (90mArms) 25Vdc (90mArms) - ELECTRICAL CHARACTERISTICS : Conditions Parameters Output Current Output Current Input Current Open Load Shutdown PWM Frequency Output Power Output Power Output Power Output Power Note 1 : Note 2 : Note 3 : Symbols Vin (V) Iout 4.75 ~ 13.2 Imin 4.75 ~ 13.2 Iin 4.75 ~ 13.2 Vbias 4.75 ~ 13.2 f(PWM) 4.75 ~ 13.2 Pout 4.75 ~ 13.2 Pout 4.75 ~ 13.2 Pout 4.75 ~ 13.2 Pout 4.75 ~ 13.2 Specification Vbr (V) Tu (°C) 0 5 0 0 0 0 0 0 0 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 -20~+70 Min. Typ. Max. TBD TBD 150 TBD TBD TBD TBD 90 10 1.0 25 TBD TBD TBD TBD TBD TBD 300 TBD TBD TBD TBD Unit Note mAdc % Adc Vdc Hz Watt Watt Watt Watt Dut y 100%, max current dut y cycle *By 12Vdc Tu: -20~+50degC Tu: -20~+70degC For one line For one line Do not use analog dimming function and external PWM for dimming at the same time. Pin terminal style converters have Molex connectors mounted. External PWM-signal is Low active. Vin 4. 75 ~ 13.2 Vdc TEST CIRCUIT : Iin A CN1-1 V CN1-2 CN3-6 CN3-5 a Vrmt 1. 5 / 2. 5 Vdc V Ext. PWM 0. 0 ~ Vin b CN3-4 SW1 D1 D1 D2 D2 Dx Dx N.C. CN1-3 CN1-4 SW2 c Connect Vbr to Ground while using ext. PWM dimming. Vbr 0. 0 ~ 5. 0 Vdc CN1-5 SW3 CN1-6 CN1-7 CN1-8 CN3-3 N.C. CN3-2 CN3-1 CABLES : For input: For output: 500 mm, stripped and tinned ends, order key < input cable # 13> For Optrex panel and Mitsubishi panel in the top: matching connectors, 200 mm, order key <Adapter cable 14> Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0, 27th November 2009