LED-CONVERTER UNIT PS-LD0403-x-yyy(S) (40W) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile LED-Converter is developed for max. 4 LED-lines APPLICABLE: 4 LED lines (Serial Mode) Pout max 7.5 Watt per line, total max. 40W LED Voltage max. 62Vdc Lamp Current per line: max. 200mAdc FEATURES : Internal Open LED Detection for every Line Analog or ext. PWM Dimming 1000:1 dimming ratio with external PWM Remote ON / OFF Wide input voltage range RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range -30°C ~ +60°C (Please contact factory for different displays) Storage Temperature Range -30°C ~ +85°C Humidity 95 %RH max DIMENSIONS : L x W x H 100 x 100 x 16 mm Weight : (g) typ. Components No. 1 2 Part Description PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) S08B-PH-SM3-TB Note t=1.0mm Molex or equal 3 Connector CN2 1 53261-1090 Molex or equal Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0.6, 14th May 2014 LED-CONVERTER UNIT PS-LD0403-x-yyy(S) (40W) (PRELIMINARY INFORMATION) Output side CN2: Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 CN 1-6 CN 1-7 Symbols GND GND N.C. Vbr Ext. PWM Vrmt Vin Ratings 0.0 ~ 5.0 (5V=low brightness) 0 ~ 0.5 = LOW / 2.5 ~ 5 = HIGH 0 ~ 0.8 = OFF / 2.5 ~ Vin = ON 21.6 ~ 26.4 Vdc CN 1-8 Vin 21.6 ~ 26.4 Vdc Pin No. CN 2-1 CN 2-2 CN 2-3 CN 2-4 CN 2-5 CN 2-6 CN 2-7 CN 2-8 CN 2-9 Symbols Vhigh(+) Vhigh(+) Vhigh(+) Vhigh(+) Vhigh(+) NC RTN1(-) RTN2(-) RTN3(-) Ratings max. 62Vdc max. 62Vdc max. 62Vdc max. 62Vdc max. 62Vdc LED LINE 1 RETURN LED LINE 2 RETURN LED LINE 3 RETURN CN 2-10 RTN4(-) LED LINE 4 RETURN *Configuration PS-LD0403-1-yyy (page 4) Output side CN2:* Pin No. CN 2-1 CN 2-2 CN 2-3 CN 2-4 Symbols Vhigh(+) Vhigh(+) Vhigh(+) Vhigh(+) Ratings max. 62Vdc max. 62Vdc max. 62Vdc max. 62Vdc CN 2-5 Vhigh(+) max. 62Vdc CN 2-6 NC - CN 2-7 RTN1(-) LED LINE 1 RETURN CN 2-8 RTN2(-) N.C. CN 2-9 RTN3(-) LED LINE 3 RETURN CN 2-10 RTN4(-) N.C. *Configuration PS-LD0403-2-yyy (page 4) ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current output Current Input Current Inrush Current Open Load Shutdown Iout Imin Imin Iin Ip Vbias Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: Vin (V) 21.6 ~ 26.4 21.6 ~ 26.4 21.6 ~ 26.4 21.6 ~ 26.4 21.6 ~ 26.4 21.6 ~ 26.4 Specification Vbr (V) Tu (°C) 0 5 0 0 0 0 -30~+60 -30~+60 -30~+60 -30~+60 -30~+60 -30~+60 Min. Typ. Max. 110 - 130 - TBD 120* 10 1 1.35 68 72 1.8 6.0 77 Unit Note mAdc % % Adc Apeak Vdc *Note 6 duty cycle analogue volt age dut y cycle ext . PWM *By 24Vdc By full load In case of not needing to connect all outputs please ask factory which pins to connect according to your needs. PWM-signal is LOW active. The external PWM-frequency should be within the range of 100 ~ 500Hz. For other frequencies please request. Output current is up to customer’s wish when no dimming function is required, Do not use analog dimming and external PWM dimming at the same time. Output voltage must be 6v higher then input voltage. Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0.6, 14th May 2014 LED-CONVERTER UNIT PS-LD0403-x-yyy(S) (40W) (PRELIMINARY INFORMATION) TEST CIRCUIT : Connect Vbr to Ground while using ext. PWM dimming. Do not connect ext. PWM dimming while using Vbr. Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (3) Version 1.0.6, 14th May 2014 LED-CONVERTER UNIT PS-LD0403-x-yyy(S) (40W) (PRELIMINARY INFORMATION) ORDER KEY : PS-LD0403-x-yyy When ordering this converter please give the following keys: -x is for different output configuration -1 four outputs -2 two outputs (by two outputs the typical current must divided with 2. -yyy is for output current (55~200mArms) Examples: PS-LD0403-1-120 (S) PCB with four outputs and 120mA current per line. PS-LD0403-2-060 (S) PCB with four outputs and 60mA current per line. For one output 120mA. CONFIGURATION CIRCUIT : PS-LD0403-1 CONFIGURATION CIRCUIT : PS-LD0403-2 CN2-1 D1 D1 D1 D1 D2 D2 D2 D2 Dx Dx Dx Dx CN2-2 CN2-3 CN2-4 CN2-5 CN2-6 N.C. CN2-7 CN2-8 CN2-9 CN2-10 CABLES : For input: 500 mm, stripped and tinned ends, order key <input cable #12> For output: 500 mm, stripped and tinned ends, order key <input cable #6> Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (4) Version 1.0.6, 14th May 2014