DC-AC INVERTER UNIT PS-DA0137-138-E-B (S) (5 W SINGLE OUTPUT) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for single lamp. Optimized for Sharp: LQ075V3DG01 APPLICABLE LCD: Lamp Voltage 890 Vrms Lamp Current 6.0 mArms Lamp Start Up Voltage 2.400 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Current balance circuit Extra high starting Voltage RoHS compliant (S) Voltage Dimming TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity L x B x H 100 x 30 x 9 mm SM02(8.0)B-BHS-1-TB (JST) DIMENSIONS : -30°C ~ +80°C -35°C ~ +85°C 95 %RH max Unit : mm Weight :15 (g) typ. Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 Part Discription PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) 53261-0690 Note t=1m m Molex or equal 3 Connector CN2 1 SM02(8.0)B-BHS-1-TB JST or equal Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstraße 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 2.0.2, 30th September 2010 DC-AC INVERTER UNIT PS-DA0137-138-E-B (S) (5 W SINGLE OUTPUT) (PRELIMINARY INFORMATION) Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 CN 1-5 Output side CN2 Symbols Ratings Vin 10.8 ~ 13.2 Vdc Vin 10.8 ~ 13.2 Vdc Vrm t 0 ~ 0.4 = OFF / 2.5 ~ Vin = ON Vbr 0 ~ 5.0 Vdc GND GND CN 1-6 Pin No. CN 2-1 CN 2-2 Symbols Vhigh N.C. Ratings 890 Vrm s (6.0 m Arm s ) - CN 2-3 Vlow (GND) - ELECTRICAL CHARACTERISTICS : Conditions Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage No Load Shotdow n Iout Iout Iin F Vopen Ts d Note 1 : Note 2: Vin (V) Vbr (V) 12±1.2 12±0.6 12±1.2 12±1.2 11.4 12±1.2 0.0 5.0 0.0 0.0 0.0 0.0 Specification Tu (°C) -30 -30 -30 -30 -30 -30 ~ +80 ~ +80 ~ +80 ~ +80 ~ +80 ~ +80 Min. Typ. Max. 5.5 50 2.200 - 6.0 15 0.6 60 2.400 1.0 6.5 0.7 70 2.700 - Unit Note m Arm s % Adc kHz Vrm s s ec Dut y 10 0 % wit hout lo ad Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Open circuit on all lamps for more than 1 sec., will shut the inverter down. TEST CIRCUIT : SW 1 Operation of unit a Operation b Non operation Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstraße 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 2.0.2, 30th September 2010