PARA LIGHT ELECTRONICS CO., LTD. 4F, No.1, Lane 93, Chien Yi Road, Chung Ho City, Taipei, Taiwan Tel: 886-2-2225-3733 Fax: 886-2-2225-4800 http://www.para.com.tw E-mail: [email protected] DATA SHEET PART NO. : L-C150JGCT REV : B / 2 CUSTOMER’S APPROVAL : _______________ DCC : ____________ DRAWING NO. : DS-71-05-0006 DATE : 2010-05-05 PAGE 1 of 14 PARA-FOR-065 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z PACKAGE OUTLINE DIMENSIONS 1 .2 0 1 .1 0 R 0 .1 0 0 .5 5 2 .1 0 0 .5 5 5 .0 0 1 .1 0 0 .4 8 ~ 0 .5 0 0 .5 0 Notes: 1. All dimensions are in millimeters. 2. Tolerance is 0.1mm (.004") unless otherwise noted. z Features ½ ½ ½ ½ ½ ½ ½ ½ Top view, wide view angle, single color Chip LED. Package in 8mm tape on 7" diameter reels. Compatible with automatic Pick & Place equipment. Compatible with Infrared and Wave soldering reflow solder processes. EIA STD package. I.C. compatible. Pb free product. Meet RoHS Green Product. DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 2 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z Chip Materials ½ ½ ½ Dice Material : AlInGaP Light Color : Super Green Lens Color : Water Clear z Absolute Maximum Ratings(Ta=25 ) Symbol Parameter Rating Unit PD Power Dissipation 60 mW IPF Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) 60 mA IF Continuous Forward Current 25 mA - De-rating Linear From 25 VR 0.25 Reverse Voltage mA/ 5 V 2000 V ESD Electrostatic Discharge Threshold(HBM)Note A Topr Operating Temperature Range -40 ~ +85 Tstg Storage Temperature Range -40 ~ +85 Note A : HBM : Human Body Model. Seller gives no other assurances regarding the ability of to withstand ESD. z Electro-Optical Characteristics(Ta=25 ) Parameter Luminous Intensity Viewing Angle Unit Test Condition 40.0 mcd IF=20mA 130 deg Note 2 Symbol Min. Typ. IV 16.0 2 1/2 Max. Peak Emission Wavelength p 571 nm Measurement @Peak Dominant Wavelength d 570 nm IF=20mA 15 nm Spectral Line Half-Width Forward Voltage VF Reverse Current IR DRAWING NO. : DS-71-05-0006 PARA-FOR-068 2.05 2.4 10 V A DATE : 2010-05-05 IF =20mA VR = 5V PAGE 3 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z Bin Code List Luminous Intensity(IV), Unit:mcd@20mA Bin Code Min Max M 18.0 28.0 N 28.0 P 45.0 Forward Voltage(VF), Unit:V@20mA Bin Code Min Max 4 1.90 2.00 45.0 5 2.00 2.10 71.0 6 2.10 2.20 7 2.20 2.30 Tolerance of each bin are 15% Tolerance of each bin are 0.1Volt Dominant Wavelength (Hue),Unit: nm@20mA Bin Code Min Max GA 567.0 570.0 GB 570.0 573.0 GC 573.0 575.0 Tolerance of each bin are 1nm Notes: 1. Luminous intensity is measured with a light sensor and filter combination that proximities the CIE eye-response curve. 2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength d is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Caution in ESD : Static Electricity and surge damages the LED. It is recommended use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. 5. Major standard testing equipment by “Instrument System” Model : CAS140B Compact Array Spectrometer and “KEITHLEY” Source Meter Model : 2400. DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 4 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z Typical Electro-Optical Characteristics Curves Ambient Temperature Unless Otherwise Noted) Luminous lntensity(mcd) (25 Fig.2 Forward Current vs.Forward Voltage Fig.3 Luminous Intensity vs.Forward Current Relative luminous intensity(%) Relative Luminous lntensity Normalized of 20mA 1000 100 10 1 -60 -40 -20 -0 20 40 60 80 100 Ambient Temperature Ta( ) Fig.4 Relative Luminous Intensity vs.Forward Current Fig.5 Luminous Intensity vs.Ambient Temperature 0° Forward Current IF(mA) 50 10° 20° 30° 40 30 20 1.0 40° 0.9 50° 0.8 60° 70° 80° 90° 10 0.7 0 0 20 40 60 80 100 0.5 0.3 0.1 0.2 0.4 0.6 Ambient Temperature Ta( ) Fig.6 Forward Current Derating Curve DRAWING NO. : DS-71-05-0006 PARA-FOR-068 Fig.7 Relative Intensity vs.Angle DATE : 2010-05-05 PAGE 5 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z Label Explanation CUS. PART NO: To be denominated. CUSTOMER: To be denominated. PART NO: Refer to P14 IV --- Luminous Intensity Code VF --- Forward Voltage Code WD --- Dominant Wavelength Code LOT NO: E L S 6 8 0001 A B C D E F A---E: For series number B---L: Local F: Foreign C---S:SMD D---Year E---Month F---SPEC. PACKING QUANTITY OF BAG : 3000pcs for 150 170 110 155 4000pcs for 191 series 5000pcs for 192 series DATE CODE 2006 06 08 G H 115 series I G--- Year H--- Month I --- Day DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 6 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z Typical Electro-Optical Characteristics Curves Fig.1 Relative Intensity vs. Wavelength z Reel Dimensions Notes: 1. Taping Quantity : 3000pcs 2. The tolerances unless mentioned is 0.1mm, Angle DRAWING NO. : DS-71-05-0006 PARA-FOR-068 0.5 , Unit : mm. DATE : 2010-05-05 PAGE 7 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z Package Dimensions Of Tape And Reel P rogressive d irection P olarity Notes:All dimensions are in millimeters. Label H:\SMD\SMD\SMD° ü × ° \± ê ? ? .jpg H:\SMD\SMD\SMD° ü × ° \± ê ? ? .jpg H:\S MD\ SMD \SMD ° °ü× \± ê ? ? .jpg Moisture Resistant Packaging Reel Label Desiccant Aluminum moistue-proof bag 240 ×° D° ü D\SM D\SM H:\SM ? .jpg \± ê ? 145 210 255 Label Box 435 Carton Notes : One reel in a bag, one bag in a inner box, ten inner boxes in a carton. Unit : mm. DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 8 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z Cleaning ½ ½ ½ If cleaning is required , use the following solutions for less than 1 minute and less than 40 . Appropriate chemicals: Ethyl alcohol and isopropyl alcohol. Effect of ultrasonic cleaning on the LED resin body differs depending on such factors as the oscillator output, size of PCB and LED mounting method. The use of ultrasonic cleaning should be enforced at proper output after confirming there is no problem. z Suggest Soldering Pad Dimensions Direction of PWB camber and go to reflow furnace DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 9 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 Suggest Sn/Pb IR Reflow Soldering Profile Condition: Suggest Pb-Free IR Reflow Soldering Profile Condition: DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 10 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 z CAUTIONS 1.Application Limitation : The LED’s described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household application).Consult PARA’s sales in advance for information on application in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LED’s may directly jeopardize life or health (such as airplanes, automobiles, traffic control equipment, life support system and safety devices). 2.Storage : Before opening the package : The LEDs should be store kept at 5°C to 30°C or less and 85%RH or less. After opening the package : The LEDs should be kept at 5°C to 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours(7 days) after opening the package. Please avoid rapid transitions in ambient temperature in high humidity environments where condensation may occur. LEDs stored out of their original packaging for more than a week should be baked at 30°C for at 24 hours before solder assembly. 3.Soldering Do not apply any stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering condition. DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 11 of 12 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 Reflow Soldering : Pre-heat 120~150°C, 120sec. MAX., Peak temperature : 240°C Max. Soldering time : 10 sec Max. Soldering Iron : (Not recommended) Temperature 300°C Max., Soldering time : 3 sec. Max.(one time only), power dissipation of iron : 20W Max. use SN60 solder of solder with silver content and don’t to touch LED lens when soldering. Wave soldering : Pre-heat 100°C Max, Pre-heat time 60 sec. Max, Solder wave 260°C Max, Soldering time 5 sec. Max. preformed consecutively cooling process is required between 1st and 2nd soldering processes. 4. Lead-Free Soldering For Reflow Soldering : 1 2 3 4 5 Pre-Heat Temp:150-180 ,120sec.Max. Soldering Temp:Temperature Of Soldering Pot Over 230 ,40sec.Max. Peak Temperature:260 5sec. Reflow Repetition:2 Times Max. Suggest Solder Paste Formula 93.3 Sn/3.1 Ag/3.1 Bi /0.5 Cu For Soldering Iron (Not Recommended) : 1 Iron Tip Temp:350 Max. 2 Soldering Iron:30w Max. 3 Soldering Time:3 Sec. Max. One Time. For Dip Soldering : 1 Pre-Heat Temp:150 Max. 120 Sec. Max. 2 Bath Temp:265 Max. 3 Dip Time:5 Sec. Max. 5. Drive Method Circuit model A Circuit model B (A)Recommended circuit. (B)The difference of brightness between LED`s could be found due to the Vf-If characteristics of LED. DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 12 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT REV:B / 2 6.Reliability Test Classification Test Item Test Condition Reference Standard Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS)*@20mA. MIL-STD-750D:1026 (1995) MIL-STD-883D:1005 (1991) JIS C 7021:B-1 (1982) IR-Reflow In-Board, 2 Times Ta= 65±5 ,RH= 90 95% *Test Time= 1000HRS±2HRS MIL-STD-202F:103B(1980) JIS C 7021:B-11(1982) Ta= 105±5 Test Time= 1000HRS (-24HRS,72HRS) MIL-STD-883D:1008 (1991) JIS C 7021:B-10 (1982) Ta= -55±5 *Test Time=1000HRS (-24HRS,72H RS) JIS C 7021:B-12 (1982) Temperature Cycling 105±5 10mins MIL-STD-202F:107D (1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1010 (1991) JIS C 7021:A-4(1982) Thermal Shock IR-Reflow In-Board, 2 Times 105±5 -55 ±5 10mins 10mins 100 Cycles MIL-STD-202F:107D(1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1011 (1991) Tsol= 260 ± 5 Dwell Time= 10 ± 1sec MIL-STD-202F:210A(1980) MIL-STD-750D:2031(1995) JIS C 7021:A-1(1982) Tsol= 235 ± 5 Immersion time 2±0.5 sec Immersion rate 25±2.5 mm/sec Coverage 95% of the dipped surface MIL-STD-202F:208D(1980) MIL-STD-750D:2026(1995) MIL-STD-883D:2003(1991) IEC 68 Part 2-20 JIS C 7021:A-2(1982) Operation Life High Temperature Endurance Test High Humidity Storage High Temperature Storage Low Temperature Storage Environmental Test Solder Resistance Solder ability -55±5 10mins 100 Cycles 7.Others: The appearance and specifications of the product may be modified for improvement without notice. DRAWING NO. : DS-71-05-0006 PARA-FOR-068 DATE : 2010-05-05 PAGE 13 of 14 SURFACE MOUNT DEVICE LED Part No. : L-C150JGCT z PART NO. SYSTEM : L–C 1 5 0 X C X X - X X X X REV:B / 2 XXXX : Special specification for customer T : Taping for 7 inch reel TC : Taping for 13 inch reel TH : IV half binning TP : Wavelength binning Lens color C : Water Clear W : White Diffused T : Color Transparent D : Color Diffused G : Gap 570nm Green Y : GaAsp 585 nm Yellow E : GaAsp 620 nm Orange SR : GaAlAs 634 nm Red KG(JG) : AlInGap 570nm Super Green KY(JY) : AlInGap 590nm Super Yellow KF : AlInGap 605nm Super Amber KR(JR) : AlInGap 630 nm Super Red LB : InGaN 470nm Blue LG: InGaN 525nm Green 0 : Single chip 1/2 : Super thin single chip 5/6 : Dual chip F : Three chip(Full color) C : Top View Type S : Side View Type DRAWING NO. : DS-71-05-0006 PARA-FOR-068 150 : 1206 1.1T 170 : 0805 0.8T 191 : 0603 0.6T 192 : 0603 0.4T 110 : 1206 1.0T DATE : 2010-05-05 Type Type Type Type Type PAGE 14 of 14