160 MHz SAW Filter 3 MHz Bandwidth Part Number SF0160BA03093S DESCRIPTION • • • 160 MHz SAW bandpass filter with 3 MHz bandwidth. 9 x 7 mm ceramic LCC package. RoHS compliant. TYPICAL PERFORMANCE Amp 10 dB/div Amp 1 dB/div Phase 15 deg/div Delay 80 ns/div Center = 160 MHz, 10 MHz/div (125 kHz incr) S11 (110-210 MHz) S22 (110-210 MHz) Spectrum Microwave, Inc. 400 Nickerson Road, Marlborough, MA 01752, USA Phone 508-251-6400 Fax 508-251-6401 www.SpectrumMicrowave.com DS0138BA03093S Rev - 20-Oct-2010 ECN 181-MAR Page 1 of 3 160 MHz SAW Filter 3 MHz Bandwidth Part Number SF0160BA03093S SPECIFICATION Parameter Center Frequency, FC 1 Minimum Insertion Loss Amplitude Ripple (159.5-160.5 MHz) Group Delay Variation (159.5-160.5 MHz) Phase Linearity (159.5-160.5 MHz) Absolute Delay 1 dB bandwidth 2 3 dB bandwidth 2 Relative Attenuation (10 to 132 MHz) 2 Relative Attenuation (132 to 146 MHz) 2 Relative Attenuation (146 to 156 MHz) 2 Relative Attenuation (164 to 174 MHz) 2 Relative Attenuation (174 to 183 MHz) 2 Relative Attenuation (183 to 193 MHz) 2 Relative Attenuation (193 to 320 MHz) 2 Input/Output Return Loss (Fc+/-150 kHz) Input IP3 3 Source and Load Impedance Temperature Coefficient of Frequency Ambient Temperature Notes: Min 2 3 55 50 20 18 50 50 46 10 37 - Typ 160 1.5 0.5 25 2 300 2.3 3.3 58 56 34 35 53 54 55 13 50 -32 25 Max 4 1 80 8 - - Units MHz dB dB p-p ns p-p deg p-p ns MHz MHz dB dB dB dB dB dB dB dB dBm ohms ppm/˚C ˚C 1. Reference frequency. Computed as mean of the 3 dB frequencies. 2. All dB values are referenced to the insertion loss value. 3. Measured inside filter passband. MAXIMUM RATINGS Parameter Storage Temperature Range Input Power Level Min -40 - Max 85 10 Units ˚C dBm MATCHING CIRCUIT 8 3 Input 50 Ω Single ended GND Output 50 Ω Single ended All other pads GND Notes: • Matching components are not required. • Device to operate in a 50 ohm single ended system. Spectrum Microwave, Inc. 400 Nickerson Road, Marlborough, MA 01752, USA Phone 508-251-6400 Fax 508-251-6401 www.SpectrumMicrowave.com DS0138BA03093S Rev - 20-Oct-2010 ECN 181-MAR Page 2 of 3 160 MHz SAW Filter 3 MHz Bandwidth Part Number SF0160BA03093S PACKAGE OUTLINE SUGGESTED FOOTPRINT SMI BA03093S ∆ YYDDD Date Code (YY = Year, DDD = Day) ESD / Pad 1 Modified pad at this location (Pad 1) Tolerances are typically ±0.15 mm except where indicated. Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating Pad Configuration: Input: 8 Output: 3 Ground: All other pads Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 µm min, over a 1.3-8.9 µm Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves right to make changes without notice. © 2010 All rights reserved. Spectrum Microwave, Inc. 400 Nickerson Road, Marlborough, MA 01752, USA Phone 508-251-6400 Fax 508-251-6401 www.SpectrumMicrowave.com DS0138BA03093S Rev - 20-Oct-2010 ECN 181-MAR Page 3 of 3