Toggles Series LP01 Short Body Pushbuttons Rockers General Specifications Electrical Capacity (Resistive Load) Pushbuttons Programmable Illuminated PB Keylocks Rotaries Slides Power Level (silver): Other Ratings D Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Contact Timing: Travel: Materials & Finishes Actuator: Housing: Base: Movable Contact: Stationary Contacts: Lamp Terminals: Tilt Tactiles Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC 50 milliohms maximum 200 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum 1,500V AC minimum between contacts and case for 1 minute minimum 500,000 operations minimum 50,000 operations minimum for 3A @ 125V/250V AC & 3A @ 30V DC 100,000 operations minimum for 1A @ 125V/250V AC & 1A @ 30V DC 1.5N for Single Pole; 3.0N for Double Pole Nonshorting (break-before-make) Total Travel .118” (3.0mm) Polycarbonate Bushing mount: Glass fiber reinforced polyamide (UL94V-0); Snap in mount: Polyphenylene ether (UL94V-0) Diallyl phthalate (UL94V-0) Phosphor bronze & silver with silver plating Common terminal: Phosphor bronze with silver plating; Contact terminals: Phosphor bronze with tin & copper plating Phospher bronze with tin and copper plating –10°C through +50°C (+14°F through +122°F) for Illuminated –25°C through +70°C (+13°F through +158°F) for Nonilluminated 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Mounting Torque: 0.8Nm (7.08 lb • in) Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section. Cleaning: Hand clean locally with alcohol based solution Standards & Certifications Flammability Standards: UL: UL94V-0 housing & base File No. E44145 All single & double pole models recognized at 3A @ 125V/250V AC or 3A @ 30V DC. Add “/U” to end of part number to order UL mark on switch. Add “/CUL” to end of part number to order cULus mark on switch. Supplement Accessories Indicators Touch Installation D66 www.nkk.com Toggles Series LP01 Rockers Distinctive Characteristics Pushbuttons Environmentally friendly components and packaging materials meet RoHS Directive restricting use of hazardous materials. Suited for lead-free soldering because of heat resistant resin materials. Smooth, slightly concave surface of cap designed to fit fingertip. Unique design and construction of cap prevents its removal and limits tampering. D Keylocks Bright LED illumination in choice of red, green, or amber through translucent white cap. Programmable Illuminated PB Short Body Pushbuttons Rotaries Short body of .551” (14.0mm) conserves behind-panel space. Slides Combination solder lug and .110” quick connect terminals. Touch Tilt Tactiles Crisp actuation and clear circuit status provided by snap-action contact mechanism. Arc barrier between movable contacts protects against crossover. Supplement Accessories Indicators Actual Size www.nkk.com D67 Series LP01 Toggles Short Body Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE 1 5 Poles C SPDT C Bushing 2 DPDT M Snap-in Circuit ON Housing (ON) K LEDs Black ( ) = Momentary Red Slides B 5D Amber 5F Green Cap Color B White Nonilluminated Cap Colors No Nonilluminated Code Switches are supplied without UL & cULus markings unless specified. Specific models & ratings noted on General Specifications page. Rotaries 5C Nonilluminated IMPORTANT: A Black C Red F Green * Wire harness & cable assemblies offered only in Americas DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Tactiles LP0115CCKW015CB White Cap Red LED SPDT ON-(ON) Circuit Bushing Mount Black Housing Tilt Silver Contacts Rated 3A @ 125/250V AC; Solder Lug/Quick Connect Terminals POLES & CIRCUIT Touch Indicators Accessories 5C Contacts & Terminals D 5 W01 K Silver Rated 3A @ 125V AC/250V AC W01 Solder Lug/ Quick Connect Terminals* Plunger Position ( ) = Momentary Supplement C Mounting Types 1 Keylocks Programmable Illuminated PB Pushbuttons Rockers LP01 Connected Terminals Throw & Power/Lamp Schematics Normal Down Normal Down 1-3 1-2 Pole Model SP LP0115 ON (ON) DP LP0125 ON (ON) Note: Terminal markings “COM, NO, NC, L, + and – ” are actually on the switch; terminal numbers are not on the switch. 1 (COM) 1-3 4-6 1-2 4-5 SPDT 3 1 (COM) DPDT 3 D68 www.nkk.com L (+) (-) L L (+) (-) L 2 2 4 6 5 Series LP01 Toggles Short Body Pushbuttons MOUNTING TYPES M Snap-in .630” (16.0mm) Diameter Rockers Bushing .669” (17.0mm) Diameter Recommended Panel Thickness: 0.2 (18.1) +– 0.0 .713 (1.7) +– 0.0 0.1 .067 0.2 (16.0) +– 0.0 Dia .630 Pushbuttons This mounting option is supplied with a brass hexagon nut with nickel plating. Recommended Panel Thickness: 0.1 (7.5) –+ 0.0 .295 .079” ~ .256” (2.0mm ~ 6.5mm) .039” ~ .126” (1.0mm ~ 3.2mm) (25.0) Min .984 (17.3) .681 (21.0) Min .827 Allow .984” (25.0mm) distance from center-to-center between switches when mounted side-by-side. D 0.2 (1.1) +– 0.0 R .043 + 0.2 – 0.0 Dia Allow .827” (21.0mm) distance from center-to-center between switches when mounted side-by-side. K Black Keylocks HOUSING Housing available in black only. The one-piece body and bezel have a matte finish. Solder Lug/ .110” (2.8mm) Quick Connect Power Level Epoxy Seal 3A @ 125V AC/250V AC; 3A @ 30V DC (0.6) R .024 (1.2) .047 Thk = (0.5) .020 Tactiles Note: If used at 1A @ 125V AC/250V AC or 1A @ 30V DC, electrical life will be 100,000 operations minimum. (7.3) .287 (2.0) .079 (2.8) .110 Slides Silver Rotaries CONTACT MATERIALS, RATINGS, & TERMINALS W01 LED COLORS & SPECIFICATIONS 5D 5F Red Amber Green Forward Peak Current I FM 30mA 30mA 30mA Continuous Forward Current IF 20mA 20mA 20mA Forward Voltage VF 1.95V 2.0V 2.1V Reverse Peak Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆I F 0.41mA/°C 0.29mA/°C 0.39mA/°C No Code –10°C ~ +50°C Supplement Ambient Temperature Range Touch Colors 5C Indicators LEDs are an integral part of the switch and are not available separately. (-) Accessories (+) Tilt The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Single Color LED with 1 Element Programmable Illuminated PB C No Lamp www.nkk.com D69 Series LP01 Toggles Short Body Pushbuttons CAP COLORS Illuminated Cap Rockers Cap Color Available: B The translucent cap is an integral part of the switch and is not available separately. White Finish: Matte Nonilluminated Caps Cap Colors Available: D A Black C Red F Green The cap is an integral part of the switch and is not available separately. Material: Polycarbonate Finish: Matte TYPICAL SWITCH DIMENSIONS Bushing Mount • Single Pole Rotaries Keylocks Programmable Illuminated PB Pushbuttons Material: Polycarbonate (3.7) .146 (1.2) x (2.0) Typ .047 x .079 M16 P1 (0.5) Typ .020 NO Slides Tactiles (2.5) .098 (7.3) .287 1 COM (3.0) .118 (5.55) .219 (21.3) .838 (5.5) .217 L –+ 2 (2.8) Typ .110 (13.6) Dia .535 (20.0) Dia .787 NC 3 NO (9.7) .382 Tilt LP0115CCKW015CB Touch Bushing Mount • Double Pole (3.7) .146 (1.2) x (2.0) Typ .047 x .079 M16 P1 NO (2.8) Typ .110 Accessories Supplement 3 (2.5) .098 (13.6) Dia .535 (20.0) Dia .787 (5.5) .217 LP0125CCKW015CB D70 www.nkk.com (7.3) .287 (21.3) .838 NC 6 L –+ 2 1 5 4 COM (6.0) .236 (11.1) .437 NO Indicators (0.5) Typ .020 (9.7) .382 Series LP01 Toggles Short Body Pushbuttons TYPICAL SWITCH DIMENSIONS Snap-in • Single Pole Rockers (3.7) .146 NO (2.5) .098 1 COM (3.0) .118 (5.55) .219 (7.3) .287 (21.3) .838 (5.5) .217 L –+ 2 (2.8) Typ .110 (13.6) Dia .535 (20.0) Dia .787 NC 3 NO (9.7) .382 Pushbuttons (0.5) Typ .020 D LP0115CMKW015CB Snap-in • Double Pole Keylocks (3.7) .146 (1.2) x (2.0) Typ .047 x .079 Programmable Illuminated PB (1.2) x (2.0) Typ .047 x .079 (0.5) Typ .020 NO (2.8) Typ .110 (9.7) .382 4 COM (7.3) .287 (6.0) .236 (11.1) .437 (21.3) .838 Slides (5.5) .217 5 LP0125CMKW015DB Tactiles (2.5) .098 (13.6) Dia .535 (20.0) Dia .787 1 NO 6 L –+ 2 Rotaries NC 3 Tilt LEGENDS NKK Switches can provide custom legends for caps. Contact factory for more information. Recommended Methods: Epoxy based ink is recommended. (12.07) Dia .475 (13.6) Dia .535 (0.76) Typ .030 Accessories Pad Print or Laser Etch on cap. Shaded area is printable area Supplement R PW Indicators Touch Suggested Printable Area for LP01 Cap www.nkk.com D71