Ordering number : ENA2015 LB1948MC Monolithic Digtal IC 12V Low Saturation Voltage Drive http://onsemi.com Forward/Reverse Motor Driver Overview The LB1948MC is a two-channel low saturation voltage forward/reverse motor driver IC. It is optimal for motor drive in 12V system products and can drive either two DC motors, one DC motor using parallel connection, or a two-phase bipolar stepping motor with 1-2 phase excitation mode drive. Features • Supports 12V power supply systems • Low saturation voltage: VO(sat) = 0.5V (typical) at IO = 400mA • Zero current drawn in standby mode • Braking function • Supports parallel connection: IO max = 1.6A, VO(sat) = 0.6V (typical) at IO = 800mA • Built-in spark killer diode • Built-in thermal shutdown circuit • Miniature package: MFP-10S (6.4mm × 5.0mm) Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Maximum supply voltage VCC max -0.3 to +20 Output voltage VOUT -0.3 to +20 V V Input voltage VIN -0.3 to +18 V Ground pin source current IGND Per channel 800 mA Allowable power dissipation Pd max Mounted on a specified board* 870 mW Operating temperature Topr -20 to +85 °C Storage temperature Tstg -40 to +150 °C * Specified board: 114.3mm × 76.1mm × 1.6mm, glass epoxy board. Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Semiconductor Components Industries, LLC, 2013 June, 2013 30712 SY 20111213-S00004 No.A2015-1/6 LB1948MC Allowable Operating Range at Ta = 25°C Parameter Symbol Conditions Ratings Unit Supply voltage VCC 2.5 to 16 V Input high-level voltage VIH 1.8 to 10 V Input low-level voltage VIL -0.3 to +0.7 V Electrical Characteristics at Ta = 25°C, VCC = 5V Parameter Symbol Ratings Conditions min Current drain Unit typ max ICC0 IN1, 2, 3, 4 = 0V (Standby mode) 0.1 10 μA ICC1 *1 (Forward or reverse mode) 15 21 mA mA ICC2 *2 (Brake mode) 30 40 Output saturation voltage VO(sat)1 IOUT = 200mA (High Side and Low Side) 0.25 0.35 VO(sat)2 IOUT = 400mA (High Side and Low Side) 0.50 0.75 V Input current IIN VIN = 5V 85 110 μA 30 μA 1.7 V V Spark Killer Diode Reverse current IS(leak) Forward voltage VSF IOUT = 400mA *1:IN1/IN2/IN3/IN4=H/L/L/L or L/H/L/L or L/L/H/L or L/L/L/H. *2:IN1/IN2/IN3/IN4=H/H/L/L or L/L/H/H. Package Dimensions unit : mm (typ) 3420 Allowable power dissipation, Pd max -- W 0.5 4.4 6.2 10 1 0.15 0.35 0.05 (1.5) 1.55 0.8 MAX 2 1.0 Pd max -- Ta 1.0 5.0 Specified board: 114.3×76.1×1.6mm3 glass epoxy board. 0.87 0.8 0.6 0.45 0.4 0.2 0 -20 0 20 40 60 80 85 100 Ambient temperature, Ta -- C SANYO : MFP10SK(225mil) Pin Assignment VCC 1 10 OUT1 IN1 2 9 OUT2 IN2 3 LB1948MC 8 OUT3 IN3 4 7 OUT4 IN4 5 6 GND Top view No.A2015-2/6 LB1948MC Truth Table Input Output Notes IN1 IN2 IN3 IN4 OUT1 OUT2 OUT3 OUT4 L L L L OFF OFF OFF OFF L L OFF OFF H L H L L H L H Reverse H H L L Brake Standby mode Standby mode 1CH Forward L L OFF OFF H L H L Standby mode L H L H Reverse H H L L Brake 2CH Forward Block Diagram 10μF VCC 60kΩ OUT1 80kΩ IN1 M IN3 60kΩ 80kΩ 60kΩ 80kΩ IN4 Thermal shutdown circuit 60kΩ 80kΩ IN2 Control block OUT2 OUT3 M OUT4 GND No.A2015-3/6 LB1948MC Design Documentation (1) Voltage magnitude relationship There are no restrictions on the magnitude relationships between the voltages applied to VCC and IN1 to IN4. (2) Parallel connection The LB1948MC can be used as a single-channel H-bridge power supply by connecting IN1 to IN3, IN2 to IN4, OUT1 to OUT3, and OUT2 to OUT4 as shown in the figure. (IOmax = 1.6A, VO(sat) = 0.6V (typical) at IO = 800mA) 1 VCC OUT1 10 2 IN1 OUT2 9 M 3 IN2 LB1948MC OUT3 8 4 IN3 OUT4 7 5 IN4 GND 6 (3) Observe the following points when designing the printed circuit board pattern layout. • Make the VCC and ground lines as wide and as short as possible to lower the wiring inductance. • Insert bypass capacitors between VCC and ground mounted as close as possible to the IC. • Resistors of about 10KΩ must be inserted between the CPU output ports and the IN1 to IN4 pins if the microcontroller and the LB1948MC are mounted on different printed circuit boards and the ground potentials differ significantly. (4) Penetration electric current At the time of the next mode shift, a penetration electric current is generated in VCC-GND. There are not the deterioration of the IC by), the destruction as follows 1Atyp per this penetration electric current (1ch, 1μs; but for the stabilization of the power supply line of the IC is most recent, and, please can enter with a condenser. (i) Forward (Reverse) ↔ Brake (ii) Forward ↔ Reverse (iii) Standby → Brake In addition, the penetration electric current disappears when I put a wait mode of 10μs at the time of the change of the Forward ↔ Reverse. (5) Supplementary matter of the penetration electric current According to (4), a penetration electric current cannot influence IC life. LB1948MC Thermal shutdown reference chart 14 VCC = 12V 100 C 12 Output voltage, VO -- V Thermal Shutdown Temperature (1) Thermal shutdown temperature The thermal shutdown temperature Ttsd is 200 ± 20°C with fluctuations. (2) Thermal shutdown operation The operation of the thermal shutdown circuit is shown in the figure below. When the chip temperature Tj is in the direction of increasing (solid line), the output turns off at approximately 200°C. When the chip temperature Tj is in the direction of decreasing (dotted line), the output turns on (returns) at approximately 125°C. 220 C Return 10 TSD operation 8 6 4 2 220 C 0 100 120 140 160 100 C 180 200 220 Chip temperature, Tj -- C No.A2015-4/6 LB1948MC Thermal Shutdown Circuit Block Diagram Reference voltage circuit Thermal shutdown circuit Drive circuit Vref Function equivalent circuit Note: The above is an example of thermal shutdown circuits although there are some differences from the actual internal circuit. Thermal Shutdown Operation The thermal shutdown circuit compares the voltage of the heat sensitive element (diode) with the reference voltage and shuts off the drive circuit at a certain temperature to protect the IC chip from overheating. ICC -- VCC 40 IIN -- VIN 400 VIN = 5V VCC = 12V 30 Input current, IIN -- μA Current drain, ICC -- mA (= IN1 / IN2 or IN3 / IN4) H/H 20 H / L, L /H 10 0 L/L 0 5 10 15 300 1~ IN 100 0 20 4 200 0 5 Supply voltage, VCC -- V VO(sat) -- IO 15 VCC = 12V VCC = 12V 0.5 (IN1 0.4 e ow 0.3 nd sid L a de h ig 0.2 20 ICC -- Ta 40 Current drain, ICC -- mA Output saturation voltage, VO(sat) -- V 0.6 10 Input voltage, VIN -- V si H 30 / 2) H /H 20 H / L, L /H 10 0.1 0 0 100 200 300 400 Output current, IO -- mA 500 600 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature, Ta -- °C No.A2015-5/6 LB1948MC Output saturation voltage, VO(sat) -- V 0.7 0.6 VO(sat) -- Ta VCC = 12V High side and Low side 00mA 0.5 IO= 4 0.4 300mA 0.3 200mA 0.2 100mA 0.1 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature, Ta -- °C ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A2015-6/6