Ordering number : ENA2213 LV8806QA Bi-CMOS IC 3-phase sensor-less http://onsemi.com Motor Driver IC Overview LV8806QA is a 3-phase sensor-less motor driver IC. 3-phase driver allows low power consumption and low vibration. And Hall sensor-less drive allows reduction of the size of a motor system. This IC is suitable for use in products which require high reliability and long life such as note PC fan. Function • Built-in current limit circuit (Operates when RF resistance is 0.5Ω and Io=0.53A) • 3-phase full-wave sensor-less driver • Direct PWM input • FG (rotation count) output signal pin • RD (lock detection) output signal pin • Built-in lock protection and auto-recovery circuit • Built-in TSD (thermal shutdown) circuit Specifications Absolute Maximum Ratings at Ta = 25°C Parameter VCC maximum supply voltage Symbol Conditions Ratings Unit VCC max 7 V OUT pin maximum output current IOUT max 0.7 A OUT(VO, VO, WO) pin withstand voltage VOUT max 7 V FG output pin maximum sink current IFG max 5 mA FG output pin withstand voltage VFG max 7 V RD output pin maximum sink current IRD max 5 mA RD output pin withstand voltage VRD max Allowable power dissipation Pd max With specified board *1 7 Operating temperature Topr *2 Storage temperature Tstg 800 V mW -40 to 95 °C -55 to 150 °C *1: With specified board: 50mm×50mm×1.6mm, grass epoxy board / single layer. *2: Tjmax must not exceed 150°C Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. ORDERING INFORMATION See detailed ordering and shipping information on page 7 of this data sheet. Semiconductor Components Industries, LLC, 2013 April, 2013 82113NK 20130729-S00005 No.A2213-1/8 LV8806QA Recommended Operating Conditions at Ta = 25°C Parameter Symbol VCC supply voltage VCC Operating VCC supply voltage range VCC op PWM input frequency range fPWM Conditions Ratings Unit 5.0 V 2.0 to 6.0 V 20 to 50 kHz Electrical Characteristics at Ta = 25°C, VCC = 5.0V Parameter Circuit current Symbol Conditions Ratings min typ Unit max ICC1 PWM=5V 1.5 2.5 mA ICC2 PWM=0V 10 50 µA Ω Output circuit ON-resistance of high-side output transistor RON(H) IO=500mA 0.5 0.9 ON-resistance of low-side output transistor RON(L) IO=500mA 0.5 0.9 Ω Sum of the ON-resistance of high/low-side RON(H+L) IO=500mA 1.0 1.8 Ω -3.25 -2.50 -1.75 µA 1.75 2.50 3.25 µA output transistor Startup oscillation (OSC) pin OSC pin charge current IOSCC OSC=0V OSC pin discharge current IOSCD OSC=1.2V OSC pin High level threshold voltage VOSCTHH 1.0 1.1 1.2 V OSC pin Low level threshold voltage VOSCTHL 0.5 0.6 0.7 V PWM pin High level input voltage VPWMH 2.5 VCC V PWM pin Low level input voltage VPWML 0 1.0 PWM pin current IPWM PWM input (PWM) pin PWM pin=0V -50 -10 V µA Forward/reverse switching (F/R) pin F/R pin High level input voltage VFRH 2.5 VCC V F/R pin Low level input voltage VFRL 0 1.0 V F/R pin current IFR FR pin=5V 10 50 µA VFG IFG=3mA 0.2 0.3 V 10 µA 0.2 0.3 V 10 µA FG, RD output pin FG pin Low level voltage FG pin leakage current IFG VFG=7V RD pin Low level voltage VRD IRD=3mA RD pin leakage current IRD VRD=7V VRF Operating when RF=0.5Ω, IO=0.53A Current limiter circuit Limiter voltage 0.238 0.265 0.291 V 0.35 0.50 0.65 S S Lock protection circuit Output ON-time LT1 Output OFF-time LT2 3.2 4.5 5.9 Output ON/OFF ratio LRTO LRTO=LT2/LT1 4.9 9.0 16.8 Operating temperature TSD *Design guarantee 150 180 °C Hysteresis width ΔTSD *Design guarantee 30 °C Thermal shutdown circuit *Design guarantee: This is a design target value, which will not be measured independently. No.A2213-2/8 LV8806QA Package Dimensions unit : mm (typ) UQFN16 2.6x2.6, 0.5P CASE 523AU ISSUE A D A B NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.25mm FROM THE TERMINAL TIP. L2 PIN ONE INDICATOR 0.20 REF 0.03 REF E 0.15 REF 0.10 C 2X 2X DETAIL A 0.10 C TOP VIEW 2X A3 0.05 C 0.42 0.61 A 10X DIM A A1 A3 b D E e L L1 L2 0.15 REF 0.26 0.28 0.05 C A1 SIDE VIEW C 15X 5 16X DETAIL A SEATING PLANE b 0.10 C A B 0.05 C 1 GENERIC MARKING DIAGRAM* 0.78 DETAIL B L 9 MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.13 REF 0.20 0.30 2.60 BSC 2.60 BSC 0.50 BSC 0.30 0.50 --0.15 0.40 0.70 16 e/2 XXXX AYW XXXX A Y W = Specific Device Code = Assembly Location = Year = Work Week = Pb -Free Package e BOTTOM VIEW RECOMMENDED SOLDERING FOOTPRINT* DETAIL B 2.90 6X 0.21 6X 0.21 2.90 15X 0.61 16X 0.33 0.50 PITCH PACKAGE OUTLINE DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. No.A2213-3/8 LV8806QA Pd max -- Ta 1.0 Specified board: 50 50 1.6mm glass epoxy board single layer. 0.8 0.6 0.35 0.4 0.2 0 20 0 40 40 60 80 100 120 Block Diagram FG 10 FG PWM 11 OSC 13 RD 9 RD REFOSC SENSORLESS LOGIC F/R SWITCH START OSC PRI DRIVE 12 F/R FIL 8 5 7 COMIN 4 SELECTOR 6 3 COM 2 VCC UO VO COM WO CURR LIM 16 GND 14 TGND1 15 TGND2 1 RF No.A2213-4/8 LV8806QA GND TGND2 TGND1 OSC Pin Assignment 16 15 14 13 RF 1 12 F/R WO 2 11 PWM LV8806QA 5 6 7 8 FIL 9 RD COMIN UO 4 COM 10 FG VCC VO 3 Top view Pin function Pin No. 1 Symbol RF Function Equivalent circuit Output current detection pin. Drive current is 5 detectable with resistors connected to GND. 2 UO Output pin. 3 VO Connected to motor coil. 4 WO 5 VCC 2 3 4 1 IC power supply pin and motor power supply pin. A capacitor is connected between GND and this pin. 6 COM Connected to the midpoint of the motor. 7 COMIN Motor position detection comparator filter pin. A capacitor is connected between FIL (PIN8) and this pin. 8 FIL UO VO WO 6 Motor position detection comparator filter pin. A capacitor is connected between COMIN (PIN7) 7 and this pin. 9 RD Motor lock detection output pin. 9 10 Outputs High when motor is locked. 10 FG 8 FG pulse output pin. This pin outputs pulse equivalent to one Hall sensor system pulse output. 11 PWM PWM signal input pin. VCC When input voltage is High, output transistor turns on. When input voltage is Low, output transistors 11 turn off, and motor stop. By controlling duty of input signal, motor rotation count is adjustable. Motor is full-speed when pin is open. 12 F/R Switches motor rotation direction. High level voltage input: U→W→V, VCC Reverse signal Low level voltage input: U→V→W. Current flow into the motor according to the above Forward/Reverse Switching signal 12 order. Motor rotates reversely when the order of Forward signal energization is changed. Continued on next page. No.A2213-5/8 LV8806QA Continued from preceding page. Pin No. 13 Symbol OSC Function Equivalent circuit Motor start-up frequency setting pin. VCC A capacitor is connected between this pin and GND. The start-up frequency is adjustable with a 13 capacitor and charge/discharge current (2.5µA). 14 TGND2 15 TGND1 16 GND GND pin of the IC Application Circuit Example (1)Application to Y-Connector Motor (2)Application to Delta-Connector Motor VCC VCC *2 *2 VCC VCC UO UO VO PWM *6 PWM VO WO PWM *6 PWM WO COM COM VCC COMIN F/R *3 *8 VCC *8 COMIN RD F/R *3 *6 FG *6 FG RD RF *5 TGND1 TGND2 GND *1 *4 OSC *7 *8 *8 FIL RD OSC *7 FIL FG *4 *7 RF *6 FG *6 RD *5 TGND1 TGND2 GND *1 *1. [Connection of power supply and GND] GND is connected to the power supply line of control circuit. *2. [Power supply stabilizer capacitor] The power supply stabilizer capacitor needs to be 4.7µA or higher. Connect VCC and GND as wide and short as possible. If the supply voltage increases due to the kickback of coil as a result of using reverse connection protector diode, make sure to connect Zener diode between the power supply and GND. LV8806QA uses synchronous rectification for high efficiency drive. Synchronous rectification is effective for heat reduction and higher efficiency. However, it may increase supply voltage under the following conditions: *When output duty is reduced rapidly. *PWM input frequency is low. If the supply voltage shall increase, make sure that it does not exceed the maximum ratings with the following measures: *Select an optimal capacitor between power supply and GND. *Insert a zener diode between power supply and GND. *3. [COMIN and FIL] COMIN and FIL are the filter capacitor connection pins. LV8806QA detects the position of rotor using BEMF signal generated during motor rotation. Based on the information, current-carrying timing of the output is determined. By inserting a filter capacitor of about 1000 to 10000pF (recommendation) between COMIN and FIL, start-up failure caused by noise is alleviated. However, if the capacitance is too high, timing of current-carrying for output may be delayed during high-speed rotation and efficiency may be degraded. Make sure that the filter capacitor is connected between COMIN and FIL as short as possible to avoid influence of noise. No.A2213-6/8 LV8806QA *4. [OSC] Capacitor connection pin for setting boot frequency. Make sure to connect a capacitor of 500pF to 2200pF (recommendation) between this pin and GND. The capacitor is required to determine boot frequency to start motor. How to define capacitance: The capacitance should allow the shortest boot time for the target rotation count and less variation. The higher the capacitance is, the more likely the variation occurs in boot time. On the other hand, the lower the capacitance is, the more likely an idling occurs. Since an optimum value for OSC pin constant varies depends on motor characteristics and boot current, make sure to confirm the constant when motor or circuit specification are changed. *5. [RF] Current limit setting pin. When a pin voltage exceeds 0.265V, current limiter operates and the mode shifts to regeneration mode. The calculation formula is as follows. RF resistance value = 0.265V / desired current limit value *6. [Pin protection resistor] It is recommended that resistors higher than 1kΩ are connected serially to protect pins against misconnection such as GND open and reverse connection. *7. [Resistor for pseudo midpoint] Delta connector motor does not have midpoint. Therefore, we need to create a pseudo midpoint by external resistor. Please note that the amplitude of BEMF signal generated during motor rotation varies depends on motor types. Some motors require the external pseudo midpoint and others do not. *8. [FG, RD pull-up resistor] Since FG and RD are open-drain output, make sure to use pull-up resistors. It is recommended that the pull-up resistor is approximately 10kΩ. ORDERING INFORMATION Device LV8806QA-MH Package UQFN16 (2.6×2.6) (Pb-Free / Halogen Free) Shipping (Qty / Packing) 3000 / Tape & Reel No.A2213-7/8 LV8806QA ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A2213-8/8