PI5USB68 PI5USB68A USB Host Charger Controller IC for Single USB Port Features Description ÎÎManages communication to allow charging to occur USB ports have become the charging connector of choice for the majority of handheld devices such as MP3 players, Mobile phones, MP4 players, DSC, and even tablet/slate type devices. ÎÎProvides multiple modes of charging to ensure all of the following specs can be met: àà USB BC1.0, 1.1, & 1.2 spec àà YD/T - 1591 charger spec àà Samsung fast charging àà Sony Ericsson fast charging àà Apple fast charging 1A and 2A àà Amazon Kindle Fire àà Certain modes available can also support devices using non standard approaches to charges such as Apple products. ÎÎAutomatic USB Device Identification Circuit (used to determine charging mode required) Although the mechanical connector has converged such that these handheld devices can charge using the same cable, the communication scheme followed by each USB device is different when it comes to setting up a charging link. Pericom’s PI5USB68/A solves the multiple communication protocol problem by supporting all protocols available in the market. Therefore, regardless of what USB device is connected to a charger enabled by Pericom, the USB device will be able to understand the charging setup communication and in turn the USB device will be able to efficiently draw current to charge itself. Îα4kV High ESD contact Protection on D+/D- per IEC61000- 4-2 specification ÎÎ-40ºC to + 85ºC Operating Temperature Range ÎÎAEC-Q100 certified ÎÎPackaging (Pb-free & Green available): àà 8-pin W8 Applications ÎÎLaptops, Netbooks ÎÎUniversal Charger including IPod ®/ IPhone ® Chargers ÎÎAutomotive 13-0070 1 2 3 4 1 2 3 4 SEL INT VDD 5 PI5USB68 Pinout GND 6 D+ GND 7 D- NC 8 VDD 5 SEL GND 6 D+ GND 7 D- 8 INT/ NC Pin Configuration PI5USB68A Pinout 1 www.pericom.com06/18/13 PI5USB68 PI5USB68A USB Host Charge Controller IC for Single USB Port Block Diagram Internal Block Diagram of PI5USB68 VDD References U3 GND 2 3 1 3 1 D+ 2 3 1 3 1 D- USB Connector 4 4 Plug/Unplug and Mode Detection References Control logic GND Pinout Table Pin I/O Name Type PI5USB68 PI5USB68A 8 8 NC N/A Do Not Connect to GND or VDD. Leave floating 7 7 GND Ground Ground 6 6 GND Ground Ground 5 5 VDD Power 5V Power Supply. Connect a 0.1 mF capacitor between VDD and GND as close as possible to the device 4 4 SEL I Control pin. Tie to ground for normal operation 3 3 D+ I/O USB connector, D+ Connection 2 2 D- I/O USB connector, D- Connection * 1 INT O n-mosfet open drain output. When observe a logic change (from H to L or from L to H). INT is LOW for ~ 2.4 seconds, otherwise, INT is hi-z. External pull-up is required O p-mosfet open source output. When observe a logic change (from H to L or from L to H). INT/ is high for ~ 2.4 seconds, otherwise INT/ is hi-z. External pull-down is required. 1 * 13-0070 INT/ Description 2 www.pericom.com06/18/13 PI5USB68 PI5USB68A USB Host Charge Controller IC for Single USB Port Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested) Note: Stresses greater than those listed under MAXIMUM Storage temperature................................................... -65 to +150ºC RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device Ambient Operating Temperature.............................. -40 to +85ºC at these or any other conditions above those indicated in Supply Voltage to Ground Potential (VDD).......................... +5.5V the operational sections of this specification is not implied. Junction Temperature...........................................................+150ºC Exposure to absolute maximum rating conditions for Soldering Temperature (Max of 10 seconds).....................+260ºC extended periods may affect reliability. All Inputs and Outputs...................................-0.5V to VDD +0.5V Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Electrical Parameters/Characteristics Recommended Operation Conditions Parameter Min. Ambient Operating Temperature VDD Power Supply Voltage (measured in respect to GND) Typ. Max. Unit -40 +85 ºC +4.75 +5.25 V DC Electrical Characteristics (VDD = 5.0V +/- 5%, Ambient Temperature -40 to +85oC) Symbol Parameter VDD Operating Voltage IDD Supply Current VDD = 5.25V VIL for SEL Input Low Voltage For SEL pin VOH for INT/ Output high voltage For INT/ pin PI5USB68 only, IOH=-4mA VOL for INT Output Low voltage For INT pin PI5USB68A only, IOL=4mA IOFF Signal voltage on D+/Dwhen chip is OFF Vdd = 0v, VIN = 0v to 5.25v 13-0070 Conditions Min. Typ. 4.75 SEL = LOW 280 Max. Unit 5.25 V 400 µA 0.6 3 4.0 V 0.25 -5 +5 µA www.pericom.com06/18/13 PI5USB68 PI5USB68A USB Host Charge Controller IC for Single USB Port DOCUMENT CONTROL NO. PD - 1001 8 REVISION: F .149 .157 DATE: 03/09/05 3.78 3.99 .0099 .0196 0.25 x 45˚ 0.50 1 .189 .196 4.80 5.00 .0075 .0098 0-8˚ 0.19 0.25 0.40 .016 1.27 .050 1 .016 .026 0.406 0.660 .2284 .2440 5.80 6.20 1.35 1.75 .053 .068 SEATING PLANE REF .050 BSC 1.27 .0040 0.10 .0098 0.25 .013 0.330 .020 0.508 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Notes: 1) Controlling dimensions in millimeters. 2) Ref: JEDEC MS-012D/AA DESCRIPTION: 8-Pin, 150-Mil Wide, SOIC PACKAGE CODE: W Note: For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php Ordering Information Ordering Code Package Code Package Type Top Mark PI5USB68WE WE Pb-free & Green, 8pin W8 PI5USB68WE PI5USB68AWE WE Pb-free & Green, 8pin W8 PI5USB68AWE • Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ • E = Pb-free and Green • Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation • 1-800-435-2336 13-0070 4 www.pericom.com06/18/13