pi3eqxdp1201

COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with Aux Listener/AutoTest mode
Features
Description
ÎÎCompliant with VESA DisplayPort 1.2 specification
PI3EQXDP1201 provides the ability to reduce signal jitter
by transmission line effects to enable longer cable length on
the 5.4Gbps DisplayPort1.2 signals.
Integrated AUX decoder can support Displayport link
training. It can decipher the link training message and automatically configure Displayport differential signal outputs
with the best pre-emphasis and output swing level settings.
Input Equalization, Output level swing and pre-emphasis
are controlled by either Aux link snooping or pin configuration. Decoding of the Aux command happens during link
training.
Built-in Sync Request Auto Test mode enables users to complete DisplayPort link status through Aux channels in minutes.
PI3EQXDP1201 is intended for use in any systems, DP signal compliance is required, including notebook PC and
docking stations, Graphic cards and digital video systems.
for HBR2, HBR, RBR rate (5.4/2.7/1.62Gbps)
ÎÎDual mode DisplayPort Outputs by providing DDC
signals across the Aux sink pin
ÎÎBuilt-in Aux interception circuit only listen to the
link training, but does not affect link training
ÎÎSink Request Auto Test Mode through Aux Channels
ÎÎDynamic EQ through Aux configuration register
programming for deterministic jitter reduction
ÎÎCable Detection pins, toggle between DP and TMDS
mode
ÎÎAutomatic power down state when HPD signal is low
ÎÎLow insertion loss across the Aux signal path
ÎÎDedicated pin control mode for Equalization setting
control
ÎÎInternally Biased AC coupled in Aux channel
ÎÎSingle Power Supply: 3.3V
ÎÎIntegrated ESD protection
ÎÎPackage : 48-pin TQFN, 7mm x 7mm
Applications
ÎÎNotebook and Dock station
ÎÎPC system boards
ÎÎDigital video systems
Typical Application
Functional Block Diagram
OUT0P/N
IN0P/N
IN1P/N
5-10” trace length
recommended
DP
Mux
DP Redriver
IN2P/N
Connector
DP++
Source
Device
IN3P/N
HPD_SRC
ENABLE
CNTRL
CAD_SRC
AUX_SRC
SCL/SDA
15-0021
Equalizer
Pre-Emphasis
1
OUT1P/N
OUT2P/N
OUT3P/N
Control Logic & Configuration Registers
Aux Listener, Aux Pass-through, DDC pass-through
Blocks
HPD_SNK
CAD_SNK
AUX_SNK
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
15-0021
SCL_DDC
V3P3
GND
AUX_SRCP
AUX_SRCN
AUX_SNKP
AUX_SNKN
ENABLE
V3P3
33
32
31
29
28
27
26
25
30
SDA_DDC
34
35
V3P3
AUTO_EQ
36
Package Pinout
DNC
37
24
GND
IN0P
38
23
OUT0P
IN0N
EQ
39
22
OUT0N
40
21
DNC
IN1P
41
20
OUT1P
IN1N
42
19
OUT1N
DNC
43
18
GND
IN2P
44
17
OUT2P
IN2N
OC_0
45
16
OUT2N
46
15
DNC
IN3P
47
14
OUT3P
IN3N
48
13
OUT3N
1
2
3
4
5
6
7
8
9
10
11
12
V3P3
DNC
OC_1
OP_0
OP_1
V3P3
CNTRL
CAD_SRC
HPD_SRC
CAD_SNK
HPD_SNK
V3P3
GND
2
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Pin Description
Pin #
Pin Name
Pin
Type
Description
1
V3P3
Power
3.3V +/10% Power rail
2
DNC
NC
3
OC_1
Input
Swing control bit 1. Pulled-up internally with 100kOhm
See truth tables for functionality
4
OP_0
Input
Pre-emphasis control bit 1. Internally pulled-up with 100kOhm
See truth tables for functionality
5
OP_1
Input
Pre-emphasis control bit 0. Internally pulled-up with 100kOhm
See truth tables for functionality
6
V3P3
Power
3.3V +/-10% Power rail
7
CNTRL
Input
Configure Output Voltage Swing and Pre-Emphasis (See truth table for functionality)
Do Not Connect; leave pin floating
Cable Adapter Detection from DP connector
8
CAD_SRC
CAD_SRC = "0" : no cable adapter; enable DP ReDriver mode with AUX listening and link
Output training active
CAD_SRC = "1" & Installed cable adapter; enable TMDS ReDriver mode and disable AUX
interception
9
HPD_SRC
Output Hot Plug detect to system DP source. 3.3V CMOS output.
10
CAD_SNK
Input
11
HPD_SNK
Input
12
V3P3
Power
13
OUT3N
Output Lane 3 data negative output
14
OUT3P
Output Lane 3 data positive output
15
DNC
16
OUT2N
Output Lane 2 data negative output
17
OUT2P
Output Lane 2 data positive output
18
GND
19
OUT1N
Output Lane 1 data negative output
20
OUT1P
Output Lane 1 data positive output
21
DNC
22
OUT0N
Output Lane 0 data negative output
23
OUT0P
Output Lane 0 data positive output
24
GND
Power
Ground
25
V3P3
Power
3.3V +/10% Power rail
26
ENABLE
Input
External Power Down pin "1"=Enable ; "0"=Disable ; Pulled-up internally with 100kOhm
27
AUX_SNKN
I/O
AUX negative channel connected to DP sink device
28
AUX_SNKP
I/O
AUX positive channel connected to DP sink device
NC
Power
NC
Cable detect from sink side.
Hot Plug Detect from the sink side
200kOhm Pull-down
3.3V +/- 10% Power rail
Do Not Connect
Ground
Do Not Connect
continued >
15-0021
3
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Pin Description
Pin #
Pin Name
Pin
Type
29
AUX_SRCN
I/O
AUX negative channel connected to DP source device
30
AUX_SRCP
I/O
AUX positive channel connected to DP source device
31
GND
Power
Ground
32
V3P3
Power
3.3V +/10% Power rail
33
SCL_DDC
I/O
DDC clock channel from source side when CAD_SNK=1
34
SDA_DDC
I/O
DDC Data channel from source side when CAD_SNK=1
35
AUTO_EQ
Input
Description
Auto EQ Control pin. Enable = “1”, Disable = “0”. This pin is internally pulled up through
100kOhm.
EQ-pin (Pin 40) can control Auto EQ mode 0, 1 and 2.
36
V3P3
Power
3.3V +/10% Power rail
37
DNC
NC
38
IN0P
Input
Lane 0 data positive input
39
IN0N
Input
Lane 0 data negative input
40
EQ
Input
Be able to configure Fixed EQ setting, when disable Auto-EQ mode (AUTO_EQ pin =“0”).
This pin is internally biased to 50% of V3P3.
41
IN1P
Input
Lane 1 data positive input
42
IN1N
Input
Lane 1 data negative input
43
DNC
NC
44
IN2P
Input
Lane 2 data positive input
45
IN2N
Input
Lane 2 data negative input
46
OC_0
Input
47
IN3P
Input
Lane 3 data positive input
48
IN3N
Input
Lane 3 data negative input
Do Not Connect
Do Not Connect
Output Control pin. See Output Control truth table for functionality
Internally pulled-high with 100kOhm
15-0021
4
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Control Pin Functional Tables
Mode
Control Pins
Normal Mode
Test Mode
Output Swing
Pre-emphasis
EQ setting
XX
800mV
0dB
Follow Auto EQ & Fixed EQ Table
X,X
Follow listener
Follow listener
Follow Auto EQ & Fixed EQ Table
00
11
400mV
0dB`
Pin Control
X
00
00
400mV
3.5dB
Pin Control
X
00
01
400mV
6dB
Pin Control
1
X
00
10
400mV
9.5dB
Pin Control
1
X
01
11
600mV
0dB
Pin Control
1
X
01
00
600mV
3.5dB
Pin Control
1
X
01
01/
600mV
6dB
Pin Control
1
X
11
11
800mV
0dB
Pin Control
1
X
11
0X/
800mV
3.5dB
Pin Control
1200mV
0dB
Pin Control
CNTRL
CAD SINK
OC_1, OC_0
OP_1, OP_0
0
1
XX
0
0
X, X
1
X
1
1
10
10
1
X
10
XX
Normal Mode
Normal
Mode
Auto EQ
mode 0
Auto EQ
mode 1
Auto EQ
mode 2
Fixed Eq.
2.5dB @
2.7GHz
Fixed Eq.
5.1dB @
2.7GHz
Fixed Eq.
7.2dB @
2.7GHz
Notes
EQ pin is internally biased to ~50% of V3P3 at
"M(Middle)" or floating statue. Measured Gains
EQ
L
Auto EQ
H
M
H
H
L
H
M
L
H
L
L
1.62G
2.7G
5.4G
Unit
L
-1.42
-2.01
-2.79
dB
M
2.41
3.9
5.16
dB
H
6.96
9.28
10.8
dB
Auto EQ pin has a internal pull-up.
EQ Setting in Auto EQ Mode
Auto EQ mode 0
Auto EQ mode 1
Auto EQ mode 2
PRE-EMPHASIS_SET Bit[4:3]
in DPCD registers
1.62G
2.7G
5.4G
1.62G
2.7G
5.4G
1.62G
2.7G
5.4G
Unit
00
2.26
2.74
2.49
3.97
5.92
7.3
3.97
7.27
8.69
dB
01
0.34
0.57
0.22
1.44
2.5
3.41
3.21
5.1
6.42
dB
10
-1.42
-2.01
-2.79
0.34
0.57
0.22
1.44
2.5
3.41
dB
11
-2.39
-3.62
-4.71
-1.42
-2.01
-2.79
0.34
0.57
0.22
dB
15-0021
5
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
00600h
Functional Description
Power Down
The AUX listener support Sink request Test sequence.
After HPD IRQ event and DP source read 00201h AUX
register and if bit 1 is high, the DP source will enter a Sink
request test mode and initiate a sequence of AUX read
request cycle. During the read cycle, data matching the following registers address are stored in the listener.
Intelligent Power Management
Pericom’s block based design and intelligent detection scheme
allow portions, or all of the IC, to be disabled for power savings. For example, in DP mode, if only one or two lanes are
active, the other lanes will be automatically powered off. If there
is no input video signal the entire IC will be powered down.
If there is no monitor detected, Pericom’s PI3EQXDP1201
can also automatically power down the IC. This intelligent
power management concept not only saves system power,
but also stops the device from outputting useless data or
noise when no signal is present at the input of the IC. The
power-down mode can also be entered using hard pin ENABLE, or through DPCD register (AUX link training)
00206hADJUST_REQUEST_LANE0_1
00207hADJUST_REQUEST_LANE2_3
00218h Test Request
00219h Test link rate
00220h Test Lane count
DisplayPort AUX Listener
After the read request cycle, the DP source will write 1 to
Bit 0 register 00260h if the DP source enters sink request
mode, or 1 to Bit 1 of register 00260h if the source declined
the sink test request. The data stored in registers 002xx
above will override the value set in 00101h to 00106h registers when the sink entered the Sink Test mode.
PI3EQXDP1201 integrates an AUX listener(decoder),
which enables the device to receive and decipher all AUX link training data and use this extracted information for its own configuration.
The intercepted DPCD data is used to adjust the active lane
count, output swing level, output pre-emphasis level, and to
manage the device’s D3 power saving state.
Sink Test Request Acknowledgement
AUX Listener Specification
00260h
mode
Buffer configuration outputs
DP AUX listener will support Native AUX CH Syntax.
Mapping of I2C onto AUX CH Syntax is not supported.
AUX listener monitors AUX channel from requester and
replier for transactions and stored AUX command from
requester and reply command from sinks that are related
to the link settings. AUX listener recovered the clock from
AUX data input by cycle counting the synchronization
pulse at the beginning of the AUX cycle. In a AUX write
request cycle, the AUX address compare the addresses
with the following registers’ address, data is extracted and
stored into the respective registers when the addresses
matches. These registers are set during link training sequence following hot plug detection.
xxxxxx00b
No action
00100 : 00106h
xxxxxx01b
Sink Test
mode
00206h,00207h,00219h,00220h
Override 00100,1,3,4,5,6h register
settings
xxxxxx10b
Sink test mode
00100h : 00106h
declined
xxxxxx11b
Not Legal code 00100h : 00106h
00100h
Data Rate Register
00101hLANE_COUNT_SET
00103hTRAINING_LANE0_SET
00104hTRAINING_LANE1_SET
00105hTRAINING_LANE2_SET
00106hTRAINING_LANE3_SET
00260h
15-0021
Sink Test request response
6
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
A complete two way AUX transaction is defined as one of
the following
1. AUX write and Sink issue ACK reply
From Source
Sync
From Source
Sync
Start/Start
4-bit cmd
20-bit
8-bit
Pattern
1000
address
length
Data
Stop
Start bit
4-bit cmd
20-bit
8-bit
1001
address
length
00001000
data = 0
Stop
From Sink NACK
Sync
Start bit
Stop
From sink ACK
Sync
Start bit
00000000
Typical AUX Test request handshake sequences with HPD_IRQ
Stop
AUX listener stores the last transaction in the register to
identify the current transaction type.
2. AUX write and Sink issue NACK reply
For Write transaction:
A data byte “M” must follow AUX NACK, “M” indicates the number of data bytes successfully written.
When a Source Device is writing a DPCD address not
supported by the Sink Device, the Sink Device shall
reply with AUX NACK and “M” equal to zero.
Source side
AUX ACK 00201h
AUX reply 00201h
AUX read 00218h
to 0027Fh
From Source
AUX reply 00218h
4-bit
Sync
Start bit
Sink side
cmd
20-bit adr
1000
8-bit
Data
length
AUX ACK 00201h..
AUX ACK 00218h
to 0027Fh
AUX write 00260h
Stop
AUX write 00260h
Enable Test registers
If bit0=1, do nothing if
bit1=1.
From sink NACK
Sync
Start bit
00010000
8-bit data byte M
Stop
3. AUX Read and Sink issue ACK reply
For Read transaction:
Ready to reply to Read request with data following.
DisplayPort receiver may assert a STOP condition
before transmitting the total number of requested data
bytes when not all the bytes are available.
From Source
Sync
Start bit
4-bit cmd
20-bit ad-
8-bit
1001
dress
length
Stop
From sink ACK
Sync
Start bit
00000000
Data
Stop
4. AUX Read and Sink issue NACK reply
For Read transaction:
A Sink Device receiving a Native AUX CH read request
for an unsupported DPCD address must reply with an
AUX ACK and read data set equal to zero instead of
replying with AUX NACK.
15-0021
7
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Start up Sequence and Hot Plug Detect (HPD) Usage
After Power on, HPD_SNK control state machine goes to Low Power state 1 and then state 2, and then monitor HPD_
SNK. At Power on Reset state, low power state 1 and low power state 2, all outputs are HiZ, equalizer is powered down,
HPD _SRC is HiZ.
At Lower Power Mode State 2, if HPD_SNK is asserted, it will turn output signals active.
If output port is active and HPD_SNK = 0, then it will go to a debounce timer and wait for 300ms, if HPD_SNK is still
=0, the controller will return to Low Power mode wait state 2.
If HPD_SNK is 1 then the controller will return to output port active state. HPD_SNK will pass through HPD _SRC.
HPD Detection & Control Circuit State Diagram
Power On
Reset
Low Power
Mode 1
Wait 2ms
Low Power
Mode 2
HPDA=1
Port A
active
HPDA=0
HPDA=1
Port A
wait
HPDA=0
15-0021
8
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Maximum Ratings(1)
(Above which useful life may be impaired. For user guidelines, not tested.)
Storage Temperature.......................................................... –65°C to +150°C
V3P3 I/O supply voltage to ground potential....................... -0.5V to 4.0V
DC Signal Voltage........................................................ -0.5V to V3P3 +0.5V
Current Output...................................................................-25mA to+25mA
Power Dissipation Continous...........................................................500mW
Operating Temperature............................................................ -40 to +85°C
ESD Protection
2
Note:
1) Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or
any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
reliability.
2) ESD results are for single supply mode only
All Pins, HBM..................................................................................2kV
DC Electrical Characteristics
Symbol
Parameters
V3P3
Condition
Min.
Typ.
Max.
Units
3.3V Power Supply
3.0
3.3
3.6
V
VIH
LVTTL input high voltage
2.4
V3P3
V
VIL
LVTTL input low voltage
GND
0.8
V
IIH
Input High-level current
VIH=2V to V3P3
-5
5
uA
IIL
Input Low-level current
VIL=GND to 0.8V
-50
-15
uA
Control Pin ENABLE
HPD_SRC and HPD_SNK Pins
VIH
LVTTL input high voltage
2.4
V3P3
V
VIL
LVTTL input low voltage
1/3*V3P3
2/3*V3P3
V
IIH
Input High-level current
GND
0.6
uA
IIL
Input Low-level current
20
40
uA
VOH
LVTTL high level output voltage
IOH=-8mA
VOL
LVTTL low level output voltage
IOL= 8mA
2.4
V
0.4
V
AUXP/N, SCL/SDA
When Configure SCL/SDA pins
IIH
Input High-level current
VIH=V3P3
-1
1
uA
Input Low-level current
When configure as Aux pins
VIL=0
-1
1
uA
Vcom
Common mode voltage
0
2.0
V
VAUX-PP
Peak to peak differential voltage
0.19
1.26
V
RON
On resistance
11
20
Ω
BW
3dB Bandwidth
IIL
15-0021
Vin = -0.3V to +0.4V
ION=-40mA
1
9
dB
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
DC Electrical Characteristics
Symbol
Parameters
Condition
Min.
Typ.
Max.
Units
mV
DP differential Input
VID
Peak to peak differential input
voltage
400
1200
VODO
Differential overshoot voltage
15%*V3P3
V3P3
VODU
Differential undershoot voltage
25%*V3P3
Ioff
Single end standby current
10
uA
V3P3
Isc
Output short current
60
mA
DP differential Output
Vtx diff-lev1
Differential pk-pk level 1
340
400
460
mV
Vtx diff-lev2
Differential pk-pk level 2
510
600
680
mV
Vtx diff-lev3
Differential pk-pk level 3
690
800
920
mV
Vtx diff-lev4
Differential pk-pk level 4
1020
1200
1380
mV
Pre-emphasis level
0dB
Vtx diff = 0.8V
0
0
0
dB
3.5dB (1.5x)
Vtx diff = 0.8V
2.8
3.5
4.2
dB
6dB (2x)
Vtx diff = 0.8V
4.8
6
7.2
dB
9.5dB (3x)
Vtx diff = 0.8V
7.6
9.5
11.4
dB
80
115
150
ps
DP differential output CML driver AC Switching Characteristics
Trise / Tfall
Rise and Fall Time
20% to 80 %
Tsk(D)
Intrapair differential skew
50
ps
Tsk(O)
Intrapair differential skew
50
ps
Power Consumption
Symbol
Condition
Icc_V3P3
ENABLE = High, HPD_SNK = High
4 DP lanes active, Pre-emphasis = 0dB,
Output Swing = 400mV
Icc_V3P3_SB
ENABLE = Low
Iccq_V3P3
PowerDown_V3P3
15-0021
Min
Typ
5.4Gbps
340
2.7Gbps
310
1.62Gbps
300
Max
Units
mA
1.4
5
mA
ENABLE = High, HPD_SNK = Low
4
20
mA
AUX Reg 600h = 02h, ENABLE= High, HPD_SNK = High,
CNTRL = Low
5
10
mA
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Measured Output Waveforms
As following is shown the actual measured output waveforms on the condition of 5.4Gbps with PRBS27-1 pattern. Auto
EQ=High; CAD_Snk=0; HPD=High; OC_1=High; OC_0=OP_0=Low; OP_1=Low; Input Level is 0.6V differential peakpeak with 12-in FR4 Length and 36-in output Coaxial Cable
Swing=400mV,
Swing=600mV,
Swing=800mV,
Preemph=0dB
Preemph=0dB
Preemph=0dB
Swing=1200mV,
Preemph=0dB
Swing=400mV,
Preemph=3.5dB
Swing=600mV,
Preemph=3.5dB
Swing=800mV,
Preemph=3.5dB
Swing=400mV,
Preemphasis=6dB
Swing=600mV,
Swing=400mV,
Preemphasis=9.5dB
Preemph=6dB
15-0021
11
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
2012
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Packaging Mechanical: 48-Contact TQFN (ZBE)
1
DATE: 03/25/10
Notes:
DESCRIPTION: 48-Pin, Thin Fine Pitch Quad Flat No-Lead (TQFN)
PACKAGE CODE: ZB48
DOCUMENT CONTROL #: PD-2080-T
REVISION: A
Note: For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php
Ordering Information
Ordering Code
Package Code
Package Type
PI3EQXDP1201ZBE
ZB
Pb-free & Green, 48-pin TQFN
1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
2. E = Pb-free and Green
3. Adding an X suffix = Tape/Reel
15-0021
12
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Related Products
Part Number
Product Description
PI3HDX1204-B
HDMI2.0 6Gbps ReDriver & Level Shifter
PI3DPX1203
DP1.3 8Gbps ReDriver
PI3HDX511D/E/F
3.4G HDMI1.4 Redriver for Source application, supporting Dual mode DisplayPort
PI3HDX412BD
1:2 Active 3.4Gbps HDMI1.4 compliant Splitter/DeMux/Redriver
PI3HDX414
1:4 Active 3.4Gbps HDMI1.4 compliant Splitter/DeMux/Redriver
PI3HDX621
2:1 3.4Gbps HDMI1.4 Switch/Re-driver with ARC and Fast Switching support for Sink Application
PI3PCIE3242
PCIe 3.0, 1-lane (2-Channel), Differential 2-Lane Exchange (2x2 matrix) switch. 3.3V for
Type-C connector
PI3WVR12412
Wide Voltage Range DisplayPort™ & HDMI Video Switch
PI3VDP12412
4-Lane DisplayPort1.2 Compliant Switch
Reference Information
Document
Description
AN
PI3EQXDP1201 Design Guideline for DisplayPort Source Application Note
15-0021
13
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Appendix:
1. Displayport Compliance Test Report
Notebook application example
Notebook Docking application example
15-0021
14
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
2. Reference Schematics
Dual-mode DP Source Application Diagram with Separate AUX and DDC Channels from Source
Dual-mode DP Source Application Diagram with Combined AUX and DDC Channels from Source
15-0021
15
www.pericom.com02/27/15
COMPANY CONFIDENTIAL
PI3EQXDP1201
3.3V, 4-Ch DisplayPort 1.2 Redriver with AUX Listener/AutoTest mode
Revision History
Version
Changes
2015/2/4
Removed 3.3/1.5V power supply and SMBus option for new design. Please contact Pericom if you need this function support.
15-0021
16
www.pericom.com02/27/15