Data Sheet

The following document contains information on Cypress products.
FUJITSU MICROELECTRONICS
DATA SHEET
DS04-27271-2E
ASSP for Power Management Applications
Buck DC/DC Converter +
Low noise LDO
MB39C022G/MB39C022J/MB39C022L
MB39C022N
■ DESCRIPTION
The MB39C022 is a 2 channels power supply IC. It consists of one channel Buck DC/DC Converter and one
channel LDO regulator. The DC/DC converter has fast transient response with current mode control topology.
Moreover, the integrated LDO provides an auxiliary output supply for noise sensitive circuit.
■ FEATURES
• Power supply voltage range
: 2.5 V to 5.5 V
• For Buck DC/DC included SW FET (CH1) : output 0.8 V to 4.5 V, 600 mA Max DC
• For LDO (CH2)
: output 3.30 V (MB39C022G) 300 mA Max DC
output 2.85 V (MB39C022J) 300 mA Max DC
output 1.80 V (MB39C022L) 300 mA Max DC
output 1.20 V (MB39C022N) 300 mA Max DC
• Error amplifier threshold voltage
: 0.3 V ± (2.5%) (CH1)
• Fast line transient response with current mode topology (CH1)
• PFM mode at light load current with VO1/VIN1 ≤ 80% (IO1 ≤ 10 mA) (CH1)
• Power-on-reset with 66 ms delay (CH1)
• Built-in short circuit protect (CH2)
• Built-in over current protect (CH1, CH2)
• Built-in thermal protection function
• Small size plastic SON-10 (3 mm × 3 mm) package
■ APPLICATIONS
•
•
•
•
•
•
Portable Equipment
PND, GPS
PMP
Mobile TV, USB-dongle (CMMB, DVB-T, DMB-T)
Smart-phone
MP3
Copyright©2009 FUJITSU MICROELECTRONICS LIMITED All rights reserved
2009.11
MB39C022
■ PIN ASSIGNMENT
(TOP VIEW)
GND1
LX
VIN1
EN1
FB
10
9
8
7
6
1
2
3
4
5
EN2
VIN2
VOUT2
POR
GND2
(LCC-10P-M04)
■ PIN DESCRIPTIONS
Block
CH1 (Buck DC/DC)
CH2 (LDO)
Control
Power
Power-on Reset
2
Pin No.
Pin name
I/O
Descriptions
6
FB
I
CH1 Error Amplifier input pin
9
LX
O
CH1 Inductor connection pin
3
VOUT2
O
CH2 LDO output pin
7
EN1
I
CH1 Control pin (L : shutdown / H : operation)
1
EN2
I
CH2 Control pin (L : shutdown / H : operation)
8
VIN1
⎯
CH1 Power supply pin
2
VIN2
⎯
CH2 Power supply pin
10
GND1
⎯
CH1 Ground pin
5
GND2
⎯
CH2 Ground pin
4
POR
O
CH1 Power on reset output pin (NMOS open drain)
DS04-27271-2E
MB39C022
■ I/O TERMINAL EQUIVALENT CIRCUIT DIAGRAM
V IN 1
E N∗
POR
∗
G ND2
∗
G ND2
V IN 1
V IN 1
∗
LX
FB
∗
G ND2
G ND1
V IN 2
∗
V O U T2
∗
G ND2
* : ESD Protection device
DS04-27271-2E
3
MB39C022
■ BLOCK DIAGRAM
<<CH1 Buck DC/DC>>
VIN1
Error
Amp.
6
8
FB
ICOMP
PFM
PWM
Logic
Control
LX
IO1 (600 mA Max)
VO1 (0.8 V to 4.5 V)
9
DRV
Current
Limit
LEVEL
CONV.
OSC
GND1
10
VIN or VO1
<<CH2: LDO>>
Error
Amp.
POR
VIN2
2
4
POR
VOUT2
3
POR
IO2 (300 mA Max)
VO2 3.3 V: MB39C022G
OCP/SCP
VIN
GND2
(2.5 V to 5.5 V)
2.85 V: MB39C022J
1.8 V: MB39C022L
1.2 V: MB39C022N
5
OTP
VREF
UVLO
EN1
7
enb1 (H: CH1 ON)
EN2
1
enb2 (H: CH2 ON)
<<10 PIN>>
4
DS04-27271-2E
MB39C022
■ FUNCTION DESCRIPTIONS
(1) PFM/PWM Logic Control Block (CH1)
The built-in P-ch and N-ch MOS FETs are controlled for synchronization rectification according to the frequency
(2.0 MHz) oscillated from the built-in oscillator (square wave oscillation circuit). Under light load, it operates
intermittently.
This circuit protects the through current caused by synchronous rectification and the reverse current in
Discontinuous Conduction Mode.
Since the PWM control circuit of this IC is in the control method in current mode, the current peak value is
monitored and controlled as required.
(2) Level converter and Iout Comparator circuit (CH1)
The Level converter circuit detects the current (ILX) which flows to the external inductor from the built-in P-ch
MOS FET. By comparing VIDET obtained through I-V conversion of peak current IPK of ILX with the Error Amp.
output, the Iout Comparator turns off the built-in P-ch MOS FET via the PWM Logic Control circuit.
(3) Error Amp. circuit (CH1)
The error amplifier (Error Amp.) detects the output voltage from the DC/DC converter and output to the current
comparators (ICOMP). The output voltage setting resistor externally connected to FB allows an arbitrary output
voltage to be set.
(4) LDO Block (CH2)
The integrated low noise low dropout regulator (LDO) is available up to 300 mA current capability and 700 mA
over current protection (OCP) 350 mA short circuit protection (SCP). The LDO output VOUT2 requires a 4.7 μF
capacitor for MB39C022G and MB39C022N and a 1.0 μF capacitor for MB39C022J and MB39C022L for stability.
MB39C022G, MB39C022J, MB39C022L and MB39C022N have fixed 3.3 V, 2.85 V, 1.8 V and 1.2 V output
voltages respectively, eliminating the need for an external resistor divider.
(5) POR Block
The POR circuit monitors the VO1 through the FB pin voltage. When the FB pin voltage reaches 97% of VFBTH,
POR pin becomes high level after the hold time of 66 ms. The POR pin is an open-drain output and pulled up
to VIN or VO1 with an external resistor.
Timing Chart : (POR pin pulled up to VIN with resistor)
VUVLO
VIN
EN1
VTH × 97%
FB
POR
thold
thold
VUVLO : UVLO threshold voltage (VTLH = 2.050 V)
VTH : FB pin threshold voltage (VTH = 0.3 V)
DS04-27271-2E
5
MB39C022
(6) Reference Voltage Block (VREF)
A high accuracy reference voltage is generated with BGR (bandgap reference) circuit.
(7) Under Voltage Lockout Protection Circuit Block (UVLO)
The circuit protects against IC malfunction and system destruction/deterioration in a transitional state or a
momentary drop of when the internal reference voltage starts. It detects a voltage drop at the VIN1 pin and stops
IC operation. When voltages at the VIN1 pin exceed the threshold voltage of the under voltage lockout protection
circuit, the system is restored.
(8) Over Temperature Protection Block (OTP)
The circuit protects an IC from heat-destruction. If the junction temperature reaches 135 °C, the circuit turns off
the CH1 and CH2 operation, When the junction temperature comes down to + 110 °C, the CH1 and CH2 are
returned to the normal operation.
(9) Control Block (CTL)
• Control function table
EN1
EN2
6
CH1 and POR
CH2
VREF, UVLO, OTP
L
L
OFF
OFF
OFF
H
L
ON
OFF
ON
L
H
OFF
ON
ON
H
H
ON
ON
ON
DS04-27271-2E
MB39C022
■ ABSOLUTE MAXIMUM RATINGS
Parameter
Power supply voltage
Input voltage
POR pull-up voltage
Symbol
Condition
Rating
Min
Max
Unit
VIN1
VIN1 pin
− 0.3
+ 6.0
V
VIN2
VIN2 pin
− 0.3
VIN1 + 0.3
V
VFB
FB pin
− 0.3
VIN1 + 0.3
V
VEN1
EN1 pin
− 0.3
+ 6.0
V
VEN2
EN2 pin
− 0.3
+ 6.0
V
VPOR
POR pin
− 0.3
+ 6.0
V
− 0.3
VIN1 + 0.3
V
LX voltage
VLX
LX pin
LX peak current
ILX
LX pin AC
⎯
1.6
A
VOUT2 peak current
IO2
VOUT2 pin AC
⎯
0.8
A
Ta ≤ + 25 °C
Power dissipation
PD
Ta = + 85 °C
Storage temperature
TSTG
⎯
⎯
2632* *
⎯
980*1, *3
⎯
1053*1, *2, *4
⎯
392*1, *3, *4
− 55
+ 125
1, 2
mW
°C
*1: When mounted on four layer epoxy board of 11.7 cm × 8.4 cm
*2: At connect the exposure pad and with thermal via (Thermal via 4 pcs).
*3: At connect the exposure pad and not thermal via.
*4: Power dissipation value between + 25 °C and + 85 °C is obtained by connecting these two points with a straight
line
Notes: • The use of negative voltages below − 0.3 V to the GND pin may create parasitic transistors on LSI lines,
which can cause abnormal operation.
• If LX terminal is short-circuited to VIN1 or VIN2 or GND line, there is a possibility to destroy it. Such usage
is prohibit
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
DS04-27271-2E
7
MB39C022
■ RECOMMENDED OPERATING CONDITIONS
Parameter
Power supply voltage
Input voltage
Output voltage
Output current
Operating ambient
temperature
Symbol
Value
Condition
Unit
Min
Typ
Max
2.5
3.7
5.5
V
VIN1
VIN1 pin*1, *3, *4, *5
VIN2
VIN2 pin*2, *3
VFB
FB pin
⎯
0.30
⎯
V
VEN1
EN1 pin
0
⎯
5.5
V
VEN2
EN2 pin
0
⎯
5.5
V
VO1
CH1 : Buck DC/DC* *
0.8
⎯
4.5
V
ILX
LX pin DC
⎯
⎯
0.6
A
VOUT2 pin DC
⎯
⎯
0.3
A
− 40
+ 25
+ 85
°C
IVOUT2
1, 5
Ta
⎯
*1 : The minimum VIN1 has to meet two conditions : VIN1 ≥ (VIN1 Min) and VIN1 ≥ VO1 + 0.5 V
*2 : The minimum VIN2 has to meet two conditions : VIN2 ≥ (VIN2 Min) and VIN2 ≥ VO2 + Vdrop (VO2 and Vdrop
values are specified in “■ ELECTRICAL CHARACTERISTICS”)
*3 : VIN1 ≥ VIN2
*4 : VIN1 startup rise time ≤ 1 ms is recommended
*5 : PFM mode at light load current with VO1/VIN1 ≤ 80% (IO1 ≤ 10 mA)
WARNING: The recommended operating conditions are required in order to ensure the normal operation of
the semiconductor device. All of the device's electrical characteristics are warranted when the
device is operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges.
Operation outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented
on the data sheet. Users considering application outside the listed conditions are advised to contact
their representatives beforehand.
8
DS04-27271-2E
MB39C022
■ ELECTRICAL CHARACTERISTICS
(Ta = + 25 °C, VIN1 = VIN2 = 3.7 V)
Symbol
Pin No.
Threshold voltage
VTH
6
FB pin
Input Bias current
IFB
6
FB = 0 V
SW PMOS-Tr On
resistor
RPON
8,9
RNON
9,10
Vline1
Parameter
CH1
SW NMOS-Tr On
[ Buck
resistor
DC/DC ]
Line regulation
Load regulation
Over current
protect
Output voltage
Condition
Value
Unit
Min
Typ
Max
− 2.5%
0.3
+ 2.5%
V
− 100
0
+ 100
nA
ILX = − 100 mA
⎯
0.35
⎯
Ω
ILX = 100 mA
⎯
0.25
⎯
Ω
⎯
VIN1 = 2.5 V to 5.5 V*1
⎯
10
⎯
mV
Vload1
⎯
IO1 = 100 mA to 600 mA
⎯
10
⎯
mV
ILIM1
9
VOUT1 × 0.9
0.9
1.2
1.5
A
IO2 = 0 mA to − 300 mA
MB39C022G
− 2.5%
3.30
+ 2.5%
V
IO2 = 0 mA to − 300 mA
MB39C022J
− 2.5%
2.85
+ 2.5%
V
IO2 = 0 mA to − 300 mA
MB39C022L
− 2.5%
1.80
+ 2.5%
V
IO2 = 0 mA to − 300 mA
MB39C022N
− 2.5%
1.20
+ 2.5%
V
VO2
3
Line regulation
Vline2
3
VIN2 = 2.5 V to 5.5 V*2
⎯
⎯
10
mV
Load regulation
Vload2
3
IO2 = 0 mA to − 300 mA
⎯
⎯
25
mV
Drop out voltage
Vdrop
3
IO2 = − 300 mA,
VIN2 = VO2 :
MB39C022G, MB39C022J
⎯
200
⎯
mV
f = 1 kHz
⎯
70*4
⎯
dB
f = 10 kHz
⎯
4
70*
⎯
dB
f = 1 kHz
⎯
65*4
⎯
dB
f = 10 kHz
⎯
65*4
⎯
dB
f = 1 kHz
⎯
60*4
⎯
dB
f = 10 kHz
⎯
4
⎯
dB
f = 1 kHz
⎯
4
⎯
dB
f = 10 kHz
⎯
4
55*
⎯
dB
⎯
55*4
⎯
μVrms
CH2
[ LDO ]
MB39C022G*3
MB39C022J*3
Power supply
rejection ratio
PSRR
3
MB39C022L*3
MB39C022N*3
60*
55*
Output noise
voltage
Vnoise
3
f = 10 Hz to 100 kHz,
EN1 = 0 V
Over current
protect
ILIM2
3
VO2 × 0.9
500
700
980
mA
Short circuit
protect
ISCP2
3
VO2 = 0 V
150
350
700
mA
(Continued)
DS04-27271-2E
9
MB39C022
(Continued)
(Ta = + 25 °C, VIN1 = VIN2 = 3.7 V)
Parameter
Symbol
Pin No.
Hold time
Thold
4
fosc = 2 MHz
Output voltage
VPOR
4
Output current
IPOR
4
Under Voltage
Lockout
Protection
Circuit Block
[ UVLO ]
Threshold
voltage
VTHL
2, 8
Hysteresis
width
VH
2, 8
Over
Temperature
Protection
Block
[ OTP ]
Stop
temperature
TOTPH
Hysteresis
width
Output
frequency
Power On
Reset
[ POR ]
Oscillator
Block
[ OSC ]
Control Block
[CTL ]
General
Condition
Value
Unit
Min
Typ
Max
52.8
66
79.2
ms
POR = 250 μA
⎯
⎯
0.1
V
POR = 5.5 V
⎯
⎯
1
μA
1.95
2.10
2.25
V
⎯
⎯
0.20
⎯
V
⎯
⎯
⎯
+ 135
⎯
°C
TOTPHYS
⎯
⎯
⎯
+ 25
⎯
°C
fosc
9
⎯
1.6
2.0
2.4
MHz
VIH
1, 7
EN1, EN2 ON
1.5
⎯
⎯
V
VIL
1, 7
EN1, EN2 OFF
⎯
⎯
0.4
V
Input current
IEN
1, 7
EN1, EN2 = 0 V
− 100
0
+ 100
nA
Shut down
power supply
current
ICC1
8
EN1, EN2 = 0 V
⎯
0
1
μA
ICC1
2
EN1, EN2 = 0 V
⎯
0
1
μA
Standby power
supply current
(DC/DC)
ICC2
8
⎯
30
60
ICC2
2
EN1 = VIN1, EN2 = 0 V
IO1 = 0 mA, VFB = VIN1
⎯
0
1
Standby power
supply current
(LDO)
ICC3
8
⎯
10
18
ICC3
2
⎯
60
120
Power-on
invalid
current
ICC4
8
⎯
0.9
1.5
mA
ICC4
2
⎯
60
120
μA
Input voltage
VIN1
EN1 = 0 V, EN2 = VIN1
IO2 = 0 mA
EN1, EN2 = VIN1,
VFB = 0.2 V
μA
μA
*1 : The minimum VIN1 has to meet two conditions : VIN1 ≥ (VIN1 Min) and VIN1 ≥ VO1 + 0.5 V
*2 : The minimum VIN2 has to meet two conditions : VIN2 ≥ (VIN2 Min) and VIN2 ≥ VO2 + Vdrop (VO2 and Vdrop
values are specified in “■ ELECTRICAL CHARACTERISTICS”)
*3 : VIN2 = VO2 + 1 V, (MB39C022N: VIN2 = 2.5 V), IO2 = 100 mA
*4 : This value is not be specified. This should be used as a reference to support designing the circuits.
10
DS04-27271-2E
MB39C022
■ TEST CIRCUIT FOR MEASURING TYPICAL OPERATING CHARACTERISTICS
EN2
EN2
GND1
C2
LX
VIN2
C4
VO2
VOUT2
VIN1
C5
VIN
C1
POR
POR
VO1
L1
EN1
R3
EN1
R5
GND2
C3
FB
R6
Component
Item
Specification
C1
Ceramic capacitor
10 μF
C2
Ceramic capacitor
4.7 μF
C3
Ceramic capacitor
22 pF
C4
Ceramic capacitor
4.7 μF
C5
Ceramic capacitor
L1
Inductor
2.2 μH
R3
Resistor
1 MΩ
R5
Resistor
600 kΩ
R6
Resistor
200 kΩ
Remarks
1 μF
for MB39C022J, MB39C022L
4.7 μF
for MB39C022G, MB39C022N
at VO1 = 1.2 V*
* : The output voltage of VO1 can be adjusted by the external resistor divider R5.
(R5 + R6)
(600 kΩ + 200 kΩ)
= 0.3 V ×
= 1.2 V
VO1 = Vref ×
R6
200 kΩ
DS04-27271-2E
11
MB39C022
■ APPLICATION NOTES
[1] Selection of components
Selection of an external inductor for DC/DC
This IC is designed to operate well with a 2.2 μH inductor. Choosing larger values would lead to larger overshoot/
undershoot during load transient. Choosing a smaller value would lead to larger ripple voltage.
The inductor should be rated for a saturation current higher than the LX peak current value during normal
operating conditions, and should have a minimal DC resistance. (100 mΩ or less is recommended to improve
efficiency.)
LX peak current value IPK is obtained by the following formula.
IPK = IOUT +
VIN − VOUT
L
×
D
fosc
L
: External inductor value
IOUT
: Load current (DC)
VIN
: Power supply voltage
×
1
2
= IOUT +
(VIN − VOUT) × VOUT
2 × L × fosc × VIN
VOUT : Output setting voltage
D
: ON- duty to be switched ( = VOUT/VIN)
fosc : Switching frequency (2.0 MHz)
ex) At VIN = 3.7 V, VOUT = 1.2 V, IOUT = 0.6 A, L = 2.2 μH, fosc = 2.0 MHz
The maximum peak current value IPK;
IPK = IOUT +
(VIN − VOUT) × VOUT
2 × L × fosc × VIN
= 0.6 A +
(3.7 V − 1.2 V) × 1.2 V
2 × 2.2 μH × 2 MHz × 3.7 V
= 0.69 A
I/O capacitor selection
• DC/DC's output capacitor's finite equivalent series resistance (ESR) causes ripple voltages on output equal
to the amount of current variation multiplied by the ESR value. The output capacitor value also has a significant
impact on the operating stability of the device when used as a DC/DC converter. Therefore, FUJITSU
MICROELECTRONICS generally recommends C2 = 4.7 μF as DC/DC output capacitor, or a larger capacitor
value can be used if ripple voltages are not suitable.
• For DC/DC, select a low ESR for the VIN1/VIN2 input capacitor to suppress dissipation from ripple currents.
In addition, to reduce startup overshoot for DC/DC and LDO, it is recommended that larger ceramic capacitor
be used for input capacitors C1 and C4. Recommended values are C1 = 10 μF, C4 = 4.7 μF.
• Types of capacitors
Ceramic capacitors are effective for reducing the ESR and afford smaller DC/DC converter circuit. However,
power supply functions as a heat generator, therefore avoid using capacitor with the F-temperature rating
( − 80% to + 20%). FUJITSU MICROELECTRONICS recommends capacitors with the B-temperature rating
( ± 10% to ± 20%).
Normal electrolytic capacitors are not recommended due to their high ESR.
Tantalum capacitor will reduce ESR, however, it is dangerous to use because it turns into short mode when
damaged. If you insist on using a tantalum capacitor, FUJITSU MICROELECTRONICS recommends the type
with an internal fuse.
12
DS04-27271-2E
MB39C022
[2] DC/DC Output voltage setting
The output voltage VO1 of this IC is defined by the external resistive divider R5 & R6. Note that C3 is a capacitor
used for improving stability. Use a 22 pF cap for C3 should be suitable in all cases.
VO1 = Vref ×
R5 + R6
R6
= 0.3 V ×
600 kΩ + 200 kΩ
200 kΩ
= 1.2 V
VO1
MB39C022
R5
C3
6 FB
R6
Vref
(0.3 V)
+
[3] Power On Reset (POR)
R3 and R4 are the pull-up resistors for POR (Pin 4). A 1 MΩ resistor is required to placed at either R3 or R4.
When R3 has a 1 MΩ resistor and R4 is open; the POR will be connected VIN. When R4 has a 1 MΩ resistor
and R3 is open; the POR pin will be connected to VO1.
By default, only R3 require a 1 MΩ resistor while R4 is open.
DS04-27271-2E
13
MB39C022
[4] Power dissipation and heat considerations
The DC/DC is so efficient that no consideration is required in most cases. The LDO, on the other hand, would
be the dominant heat generator due to its inherent efficiency loss. Thus, if the IC is used at a high power supply
voltage, heavy load, and low LDO output voltage, or high temperature, it requires further consideration.
The internal loss (Pc) is roughly obtained from the following formula :
PC = PC1 + PC2 = IO12 × (RDC + D × RONP + (1 − D) × RONN) + IO2 × Vdrop
PC1
: DC/DC continuity loss
PC2
: LDO continuity loss
RDC
: External inductor series resistance ( < 100 mΩ recommended)
D
: Switching ON-duty cycle ( = VOUT / VIN)
RONP
: Internal P-ch SW FET ON resistance
RONN
: Internal N-ch SW FET ON resistance
IO1
: DC/DC Load current
IO2
: LDO Load current
Vdrop
: LDO Dropout voltage
The loss expressed by the above formula is continuity loss. The internal loss includes the switching loss and the
control circuit loss as well but they are so small compared to the continuity loss they can be ignored.
For PC1, consider the scenario with high temperature and heavy load (VIN = 3.7 V, VO1 = 1.2 V, IO1 = 0.6 A, Ta =
+ 70 °C). Here, RONP =: 0.4 Ω and RONN =: 0.3 Ω according to the graph “MOS FET ON resistance vs. Operating
ambient temperature”. PC1 = 156 mW.
For PC2, consider the scenario with low output voltage (MB39C022N), high temperature and heavy load
(VIN = 3.7 V, VO2 = 1.2 V, IO2 = 0.3 A, Ta = + 70 °C). Here, PC2 = 0.75 W. Note that PC2 >> PC1.
According to the graph “Power dissipation vs. Operating ambient temperature”, the maximum permissible power
dissipation at an operating ambient temperature Ta of + 70 °C is 1.4 W. The internal loss is lower than the
maximum permissible power dissipation.
14
DS04-27271-2E
MB39C022
[5] Board layout, design example
Some basic design guidelines should be used when physically placing the MB39C022 on a Printed Circuit Board
(PCB).
• Regarding to GND pattern of PCB layout of MB39C022, It needs to separate like AGND (analog ground) and
PGND (power ground). By separating grounds, it is possible to minimize the switching frequency noise on the
LDO output.
• Arrange the input capacitor C1 and C4 as close as possible between VIN1 & PGND pins and VIN2 & AGND
pins. Make a through hole near the pins of this capacitor if the board has planes for power and GND.
• Large AC currents flow between this IC and the input capacitor (C1), output capacitor (C2), and external
inductor (L1). Group these components as close as possible to this IC to reduce the overall loop area occupied
by this group. Also try to mount these components on the same surface and arrange wiring without through
hole wiring. Use thick, short, and straight routes to wire the net (The layout by planes is recommended.).
• The C1 and C2 capacitor returns are connected closely together at the PGND plane.
• The LDO input capacitor (C4) and LDO output capacitor (C5) are returned to the AGND plane.
• The analog ground plane and power ground plane are connected at one point.
• All other signals (EN1, EN2, FB) should be referenced to AGND and have the AGND plane underneath them.
• The feedback wiring to the VO1 and the VO1 pin should be wired closest to the output capacitor (C2). The
resistive divider and FB pin is extremely sensitive and should thus be kept wired away from the LX pin of this
IC as far as possible.
• Try to make a GND plane on the surface to which this IC will be mounted. For efficient heat dissipation when
using the SON-10 package, FUJITSU MICROELECTRONICS recommends providing a thermal via in the
footprint of the thermal pad.
Layout Example of IC components
VO1
PGND
PGND
Plane
C2
AGND Plane
VIN2
L1
PGND
AGND
C4
C1
C5
VIN1
VO2
DS04-27271-2E
R5
R6
15
MB39C022
■ EXAMPLE OF STANDARD OPERATION CHARACTERISTICS
(Shown below is an example of characteristics for connection according to “■ TEST CIRCUIT FOR MEASURING
TYPICAL OPERATING CHARACTERISTICS”.)
(1) DC/DC Conversion Efficiency
Conversion Efficiency η (%)
CH1 Test Condition :
EN1 = VIN; EN2 = 0 V
VO1 = 1.2 V; C1 = 10 μF; C2 = 4.7 μF
100
90
80
70
60
50
40
30
20
10
0
0.001
VIN = 3.7 V
VIN = 4.3 V
VIN = 5.5 V
0.01
0.1
1
Load Current IO1 (A)
(2) DC/DC Load Regulation
Output Voltage VO1 (V)
CH1 Test Condition :
EN1 = VIN; EN2 = 0 V
VO1 = 1.2 V; C1 = 10 μF; C2 = 4.7 μF
1.3
1.28
1.26
1.24
1.22
1.2
1.18
1.16
1.14
1.12
1.1
VIN = 3.7 V
VIN = 4.3 V
VIN = 5.5 V
0
16
0.2
0.4
Load Current IO1 (A)
0.6
DS04-27271-2E
MB39C022
(3) DC/DC Line Regulation
Output Voltage VO1 (V)
CH1 Test Condition :
EN1 = VIN; EN2 = 0 V
VO1 = 1.2 V; C1 = 10 μF; C2 = 4.7 μF
1.3
1.28
1.26
1.24
1.22
1.2
1.18
1.16
1.14
1.12
1.1
IO1 = 0 mA
IO1 = 300 mA
IO1 = 600 mA
3.2
3.7
4.2
4.7
Input Voltage VIN (V)
5.2
(4) DC/DC Switching Waveform
CH1 Test Condition :
EN1 = EN2 = VIN = 3.7 V;
VO1 = 1.8 V; IO1 = 250 mA; C1 = 10 μF; C2 = 4.7 μF
VO2 = 3.3 V; IO2 = 150 mA; C4 = C5 = 4.7 μF
VLx
5 V/div
ILx
100 mA/div
VO1
20 mV/div
VO2
20 mV/div
500 ns/div
DS04-27271-2E
17
MB39C022
(5) LDO Load Regulation
MB39C022G CH2 Test Condition :
EN2 = VIN; EN1 = 0 V
VO2 = 3.3 V; C4 = C5 = 4.7 μF
Output Voltage VO2 (V)
3.4
3.38
VIN = 3.7 V
3.36
VIN = 4.3 V
VIN = 5.5 V
3.34
3.32
3.3
3.28
3.26
3.24
3.22
3.2
0
0.05
0.1
0.15
0.2
0.25
0.3
Load Current IO2 (A)
(6) LDO Line Regulation
MB39C022G CH2 Test Condition :
EN2 = VIN; EN1 = 0 V
VO2 = 3.3 V; C4 = C5 = 4.7 μF
3.4
Output Voltage VO2 (V)
3.38
IO2 = 0 mA
3.36
IO2 = 120 mA
3.34
IO2 = 300 mA
3.32
3.3
3.28
3.26
3.24
3.22
3.2
3.6
4.1
4.6
5.1
Input Voltage VIN (V)
18
DS04-27271-2E
MB39C022
(7) LDO Power Supply Rejection Ratio
MB39C022G CH2 Test Condition :
EN2 = VIN = 3.7 V; EN1 = 0 V
VO2 = 3.3 V; IO2 = 100 mA; C1 = C4 = 0 μF
PSRR (dB)
0
−10
VIN = 3.7 V
−20
VIN = 4.3 V
−30
−40
−50
−60
−70
−80
−90
10
100
1000
10000
Frequency (Hz)
100000
1000000
(8) DC/DC Load Transient Waveforms
Test Condition :
VIN = EN1 = EN2 = 3.7 V; VO1 = 1.2 V; C1 = 10 μF; C2 = 4.7 μF; VO2 = 3.3 V; C4 = C5 = 4.7 μF
T
IO1 = 10 mA to 400 mA
IO1
500 mA/div
VO1
100 mV/div
VO2
IO2 = 150 mA
20 mV/div
100 μs/div
CH1 Load Transient Waveforms
DS04-27271-2E
19
MB39C022
N-ch MOS FET ON Resistance RON (Ω)
MOS FET ON Resistance RON (Ω)
MOS FET ON Resistance vs. Input Voltage
20
0.6
0.5
P-ch
0.4
0.3
0.2
N-ch
0.1
0.0
2.0
3.0
4.0
5.0
6.0
Input voltage VIN (V)
P-ch MOS FET ON Resistance RON (Ω)
(9) DC/DC Power MOS FET ON Resistance
P-ch MOS FET ON Resistance vs.
Operating Ambient Temperature
0.6
0.5
0.4
VIN = 3.7 V
0.3
0.2
0.1
0.0
-50
VIN = 5.5 V
0
50
100
Operating Ambient Temperature Ta ( °C)
N-ch MOS FET ON Resistance vs.
Operating Ambient Temperature
0.6
0.5
VIN = 3.7 V
0.4
0.3
0.2
VIN = 5.5 V
0.1
0.0
-50
0
50
100
Operating Ambient Temperature Ta ( °C)
DS04-27271-2E
MB39C022
Permissible Power Dissipation vs. Operating Ambient Temperature
3000
2630
Power Dissipation PD (mW)
2500
2000
1500
1000
500
0
-40
-20
0
20
40
60
80
100
Operating Ambient Temperature Ta ( °C)
DS04-27271-2E
21
MB39C022
■ APPLICATION CIRCUITS EXAMPLES
EXAMPLE 1 (VIN1 = VIN2)
VIN1 and VIN2 are connected together and POR is pulled up to VIN
(MB39C022)
EN2
EN2
GND1
C2
VIN2
C4
VO2
IO2 ≤ 300 mA
L1
VOUT2
VIN1
C5
VIN
C1
POR
POR
VO1
IO1 ≤ 600 mA
LX
EN1
EN1
R3
R6
GND2
C3
FB
R5
EXAMPLE 2 (VIN2 = VO1)
• VIN2 is connected to VO1 and POR is pulled up to VIN
• It is possible to maximize LDO efficiency by connecting DC/DC Output to LDO supply.
• Maximum DC/DC output current ( = IO1) is limited by VIN2 input current ( =: IO2)
(MB39C022)
EN2
EN2
GND1
C2
VIN2
C4
VO2
IO2 ≤ 300 mA
L1
VOUT2
VIN1
C5
POR
VO1
IO1 ≤ 600 mA - IO2
LX
VIN
C1
POR
EN1
EN1
R3
R6
GND2
C3
FB
R5
22
DS04-27271-2E
MB39C022
EXAMPLE 3 (POR and RC delay channel control)
• EN1 is controlled by RC delay and EN2 is controlled by POR output.
• It is possible to control each channel without signal from MCU
R3
(MB39C022)
EN2
GND1
C2
VIN2
L1
C4
VO2
IO2 ≤ 300 mA
VO1
IO1 ≤ 600 mA
LX
VOUT2
VIN1
C5
VIN
C1
100 kΩ
POR
POR
EN1
1 μF
R5
GND2
C3
FB
R6
Timing chart
VIN
VUVLO
Vth(POR)
VO1
(1.2 V)
VO2
(1.8 V)
tc
ta
tb
td
Start up control
ta : RC delay time (28 ms at VIN = 3.7 V, R = 100 kΩ, C = 1 μF)
tb : POR hold time (66 ms fixed)
Power down control
tc, td : depend on internal discharge path and output loading
DS04-27271-2E
23
MB39C022
■ USAGE PRECAUTIONS
1. Never use setting exceeding maximum rated conditions.
Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature,
etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
2. Use the devices within recommended conditions
It is recommended that devices be operated within recommended conditions.
Exceeding the recommended operating condition may adversely affect devices reliability.
Nominal electrical characteristics are warranted within the range of recommended operating conditions otherwise
specified on each parameter in the section of electrical characteristics.
3. Design the ground line on printed circuit boards with consideration of common impedance.
4. Take appropriate measures against static electricity.
The LX pin has less built-in ESD protection than other pins.
LX pin : 150 V (MM), 1500 V (HBM), Other pins : 200 V (MM), 2000 V (HBM)
Containers for semiconductor materials should have anti-static protection or be made of conductive material.
After mounting, printed circuit boards should be stored and shipped in conductive bags or containers.
Work platforms, tools, and instruments should be properly grounded.
Working personnel should be grounded with resistance of 250 kΩ to 1 MΩ between body and ground.
5. Do not apply negative voltages
The use of negative voltages below − 0.3 V may activate parasitic transistors on the device, which can cause
abnormal operation.
24
DS04-27271-2E
MB39C022
■ ORDERING INFORMATION
Part number
Package
Remarks
MB39C022GPN
MB39C022JPN
MB39C022LPN
10-pin plastic SON
(LCC-10P-M04)
MB39C022NPN
DS04-27271-2E
25
MB39C022
■ RoHS COMPLIANCE INFORMATION OF LEAD(Pb) FREE VERSION
The LSI products of FUJITSU MICROELECTRONICS with “E1” are compliant with RoHS Directive, and has
observed the standard of lead, cadmium, mercury, chromium, polybrominated biphenyls (PBB), and polybrominated diphenylethers (PBDE).
A product whose part number has trailing characters “E1” is RoHS compliant.
26
DS04-27271-2E
MB39C022
■ PACKAGE DIMENSION
10-pin plastic SON
Lead pitch
0.50 mm
Package width ×
package length
3.00 mm × 3.00 mm
Sealing method
Plastic mold
Mounting height
0.75 mm MAX
Weight
0.018 g
(LCC-10P-M04)
10-pin plastic SON
(LCC-10P-M04)
3.00±0.10
(.118±.004)
2.40±0.10
(.094±.004)
10
6
INDEX AREA
3.00±0.10
(.118±.004)
1.70±0.10
(.067±.004)
0.40±0.10
(.016±.004)
1
5
1PIN CORNER
(C0.30(C.012))
0.50(.020)
TYP
0.25±0.03
(.010±.001)
0.05(.002)
0.00
(.000
C
+0.05
–0.00
+.002
–.000
0.75(.030)
MAX
0.15(.006)
)
2008 FUJITSU MICROELECTRONICS LIMITED C10004S-c-1-2
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
Please check the latest package dimension at the following URL.
http://edevice.fujitsu.com/package/en-search/
DS04-27271-2E
27
MB39C022
FUJITSU MICROELECTRONICS LIMITED
Shinjuku Dai-Ichi Seimei Bldg., 7-1, Nishishinjuku 2-chome,
Shinjuku-ku, Tokyo 163-0722, Japan
Tel: +81-3-5322-3329
http://jp.fujitsu.com/fml/en/
For further information please contact:
North and South America
FUJITSU MICROELECTRONICS AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600 Fax: +1-408-737-5999
http://www.fma.fujitsu.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE. LTD.
151 Lorong Chuan,
#05-08 New Tech Park 556741 Singapore
Tel : +65-6281-0770 Fax : +65-6281-0220
http://www.fmal.fujitsu.com/
Europe
FUJITSU MICROELECTRONICS EUROPE GmbH
Pittlerstrasse 47, 63225 Langen, Germany
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/microelectronics/
FUJITSU MICROELECTRONICS SHANGHAI CO., LTD.
Rm. 3102, Bund Center, No.222 Yan An Road (E),
Shanghai 200002, China
Tel : +86-21-6146-3688 Fax : +86-21-6335-1605
http://cn.fujitsu.com/fmc/
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
206 Kosmo Tower Building, 1002 Daechi-Dong,
Gangnam-Gu, Seoul 135-280, Republic of Korea
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://kr.fujitsu.com/fmk/
FUJITSU MICROELECTRONICS PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel : +852-2377-0226 Fax : +852-2376-3269
http://cn.fujitsu.com/fmc/en/
Specifications are subject to change without notice. For further information please contact each office.
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose
of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS
does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating
the device based on such information, you must assume any responsibility arising out of such use of the information.
FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use
or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS
or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or
other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured
as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to
the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear
facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon
system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising
in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current
levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of
the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited: Sales Promotion Department