PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch Features Description Low On-Resistance: 10-ohm max. The PI5A4599A is an improved, direct replacement for the MAX4599 single-pole, double-throw (SPDT) analog switch. Improved specifications include a low maximum ON resistance of 10-ohm and fast switching times (tON = 15ns max., tOFF = 7ns max.) with 5V supply operation. With a 2.5V supply, resistance is a low 400-ohm max. RON Matching: 2-ohm max. RON Flatness: 3.5-ohm max. Low 0.5nA Input Leakage at 25 °C 2V to 6V Single-Supply Operation Specifications are given for 2.5V, 3.3V and 5V power supply operation. Operating voltage range is 2.0V to 6.0V. Fast Switching Time 15ns tON 7ns tOFF Break-Before-Make Switching Guaranteed To minimize PC board area use, the PI5A4599A is available in a compact 6-pin SC70 package. Operating temperature range is – 40°C to 85°C. 5pC max Charge Injection 225MHz Channel Bandwidth 76dB Off-Isolation at 1MHz TTL/CMOS Logic Compatible Low Power Consumption: 5μW Improved Direct Replacement for MAX4599 Packaging (Pb-free & Green available): 6-pin Small Compact SC70 (C) 6-pin SOT23 (T) Functional Diagram, Pin Configuration Applications Communication Circuits Cellular Phones IN 1 6 NO V+ 2 5 COM GND 3 4 NC Audio and Video Signal Routing Portable Battery-Operated Equipment Data Acquisition Systems Computer Peripherals Telecommunications Relay Replacement SOT23; SC70-6 Wireless Terminals and Peripherals Top View Switches shown for Logic “0” input Truth Table PI5A4599A Logic NC NO 0 ON OFF 1 OFF ON All trademarks are property of their respective owners. 1 09-0001 www.pericom.com PS8553C 10/26/09 PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch Absolute Maximum Ratings Thermal Information Voltages Referenced to GND Continuous Power Dissipation V+..........................................................................–0.5V to +7V SC70-6 (derate 3.1mW/ºC above +70ºC)............................245mW VIN, VCOM, VNC , VNO (Note 1)..........................–0.5V to VCC +2V Storage Temperature..............................................–65ºC to +150ºC or 30mA, whichever occurs first Lead Temperature (soldering, 10s).......................................+300ºC Current (any terminal)........................................................±30mA Peak Current, COM, NO, NC Note: Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to 30mA. (Pulsed at 1ms, 10% duty cycle)........................................±30mA Caution: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Th is is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Electrical Specifications - Single +5V Supply (V+ = +5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V) Parameter Symbol Conditions Temp. (C°) Min. (1) Typ. (2) Max. (1) Units Analog Switch Analog Signal Range (3) VANALOG On Resistance RON On-Resistance Match Between Channels (4) ΔRON On-Resistance Flatness (5) RFLAT(ON) NO or NC Off Leakage Current (6) INO(OFF) or INC(OFF) COM Off Leakage Current (6) ICOM(OFF) On Leakage Current (6) ICOM(ON) Full V+ 25 V+ = 4.5V, ICOM = -30mA, Full VNO or VNC = +2.5V 25 7 V 8 10 0.1 Full 0.5 1 V+ = 5V, ICOM = -30mA, 25 2.72 VNO or VNC = 1V, 2.5V, 4V Full V+ = 5.5V, VCOM = 0V, 25 –0.5 VNO or VNC = 4.5V Full –5 V+ = 5.5V, VCOM = + 4.5V, 25 –1.0 VNO or VNC = ± 0V Full –10 V+ = 5.5V , VCOM = +4.5V 25 –1.0 VNO or VNC = +4.5V Full –10 Ω 3.5 4 0.18 0.5 5 20 1.0 10 20 nA 1.0 10 Continued All trademarks are property of their respective owners. 2 09-0001 www.pericom.com PS8553C 10/26/09 PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch Electrical Specifications - Single +5V Supply (V+ = +5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V) Parameter Symbol Conditions Temp. (C°) Input High Voltage VIH Guaranteed logic High Level Input Low Voltage VIL Guaranteed logic Low Level Min. (1) Typ. (2) Max. (1) Units Logic Input Input Current with Voltage IINH High VIN = 2.4V, all others = 0.8V Input Current with Voltage IINL Low VIN = 0.8V, all others = 2.4V 2 0.8 Full –1 0.005 V 1 μA –1 0.005 1 7 15 Dynamic Turn-On Time 25 tON Full VCC = 5V, Figure 1 Turn-Off Time tOFF Break-Before-Make tBBM Charger Injection (3) Q 20 25 Figure 3 7 Full 10 25 10 Full CL =1nF, VGEN = 0V, 1 ns 5 25 1.5 5 pC RGEN = 0Ω, Figure 2 Off Isolation OIRR R L = 50Ω, CL = 5pF, 80 f = 1MHz, Figure 4 dB R L = 50Ω, CL = 5pF, Crosstalk (8) XTALK NC or NO Capacitance C(OFF) COM Off Capacitance CCOM(OFF) COM ON Capacitance CCOM(ON) f = 1MHz, Figure 7 -3dB Bandwidth BW R L = 50Ω, Figure 8 80 f = 1MHz, Figure 5 5.0 f = 1MHz, Figure 6 pF 5.0 13 Full 300 MHz Supply Power Supply Range V+ Positive Supply Current I+ VCC = 5.5V, VIN = 0V or V+ Full 2 6 V 1 μA 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ΔRON = RON max. - RON min. 5. Flatness is defined as the difference between the maximum and minimum value of On-resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC. 7. Off Isolation = 20log10 [ VCOM / (V NO or V NC) ]. See Figure 3. 8. Between any two switches. See Figure 4. All trademarks are property of their respective owners. 3 09-0001 www.pericom.com PS8553C 10/26/09 PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch Electrical Specifications - Single +3.3V Supply (V+ = +3.3V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V) Parameter Symbol Test Conditions Temp. (C°) Min. (1) Typ. (2) Max. (1) Units 0 V+ Analog Switch Analog Signal Range (3) VANALOG On Resistance RON On-Resistance Match Between Channels (4) ΔRON On-Resistance Flatness (3, 5) RFLAT(ON) V+ = 3V, ICOM = -30mA, 25 VNO or VNC = 1.5V Full 12 Full VNO or VNC = 0.8V, 2.5V 25 14.0 17 25 V+ = 3.3V, ICOM = -30mA, V 0.2 0.5 Ω 1 5 Full 4 5 Logic Input Input High Voltage VIH Guaranteed logic High Level Input Low Voltage VIL Guaranteed logic Low Level Input High Current IINH VIN = 2.4V, all others = 0.8V Input Low Current IINL VIN = 0.8V, all others = 2.4V 2 Full 0.8 –1 1 –1 1 V μA Dynamic Turn-On Time 25 tON V+ = 3.3V, VNO or VNC = 1.5V, Figure 1 Turn-Off Time tOFF Break-Before-Make tBBM Charger Injection (3) Q 15 Full 40 25 1.5 Full Full CL =1nF, VGEN = 0V, 12 20 25 Figure 3 25 ns 10 5 25 1.3 5 pC 1 μA RGEN = 0Ω, Figure 2 Supply Positive Supply Current I+ V+ = 3.6V, VIN = 0V or V+ All channels on or off Full 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ΔRON = RON max. - RON min. 5. Flatness is defined as the difference between the maximum and minimum value of On-resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC. 7. Off Isolation = 20log10 [ VCOM / (V NO or V NC) ]. See Figure 4. 8. Between any two switches. See Figure 5. All trademarks are property of their respective owners. 4 09-0001 www.pericom.com PS8553C 10/26/09 PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch Electrical Specifications - Single +2.5V Supply (V+ = +2.5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V) Parameter Symbol Test Conditions Temp. (C°) Min. (1) Typ. (2) Max. (1) Units 0 V+ Analog Switch Analog Signal Range (3) VANALOG On Resistance RON On-Resistance Match Between Channels (4) ΔRON On-Resistance Flatness (3, 5) RFLAT(ON) V+ = 2.5V, ICOM = -30mA, 25 VNO or VNC = 1.5V Full 20 Full VNO or VNC = 0.8V, 2.5V 25 22 26 25 V+ = 2.5V, ICOM = -30mA, V 0.3 0.5 Ω 1 0.5 Full 6 6 Logic Input Input High Voltage VIH Guaranteed logic High Level Input Low Voltage VIL Guaranteed logic Low Level Input High Current IINH VIN = 2.4V, all others = 0.8V Input Low Current IINL VIN = 0.8V, all others = 2.4V 2 Full 0.8 –1 1 –1 1 V μA Dynamic Turn-On Time tON V+ = 2.5V, VNO or VNC = 1.5V, Figure 1 Turn-Off Time tOFF Break-Before-Make tBBM Charger Injection (3) Q Figure 3 25 20 30 Full – 45 25 Full – 25 10 Full CL =1nF, VGEN = 0V, 20 30 ns 5 25 0.9 5 pC 1 μA RGEN = 0Ω, Figure 2 Supply Positive Supply Current I+ V+ = 2.5V, VIN = 0V or V+ All channels on or off Full 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ΔRON = RON max. - RON min. 5. Flatness is defined as the difference between the maximum and minimum value of On-resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC. 7. Off Isolation = 20log10 [ VCOM / (V NO or V NC) ]. See Figure 4. 8. Between any two switches. See Figure 5. All trademarks are property of their respective owners. 5 09-0001 www.pericom.com PS8553C 10/26/09 PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch Switch 3 np t o ic 3 np t 0 C or C 50 20ns 20ns t C 35p Switch tp t o ic np t C tr tf 90 90 0 t C S A S A CAPAC A C C C S 1.5 P A S A A 3.3 S PP S PP S C Figure 1. Switching Time +5V DVOUT V+ COM VGEN VOUT NO or NC VOUT CL 0.22nF .1µF IN OFF ON OFF IN Logic Input GND IN ON OFF OFF Q = (DVOUT)(CL) Figure 2. Charge Injection V+ Logic Input V+ +3V NC VOUT COM +3V 0 50% NO RL 1kW IN Logic Input CL 35pF 0.9xVOUT Switch Output (VOUT) GND 0.9xVOUT tBBM CL INCLUDES FIXTURE AND STRAY CAPACITANCE Figure 3. Break-Before-Make Interval All trademarks are property of their respective owners. 6 09-0001 www.pericom.com PS8553C 10/26/09 PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch 5 10n C CC 10n 0 or 2. C or C Si nal enerator 0d m 1 C Analy er Analy er Figure 5. Crosstalk Figure 4. Off Isolation/On-Channel Bandwidth +5V 10nF +5V 10nF COM COM V+ IN V+ Capacitance Meter 0V or 2.4V IN f = 1MHz Capacitance Meter 0V or 2.4V NC f = 1 MHz GND NC GND Figure 7. Channel-On Capacitance Figure 6. Channel-Off Capacitance +5V 10nF V+ COM NC or NO Vo RL 50Ω Rg = 50Ω GND Figure 8. Bandwidth All trademarks are property of their respective owners. 7 09-0001 www.pericom.com PS8553C 10/26/09 PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch Packaging Mechanical: 6-Pin SC70 (C) DOCUMENT CONTROL NO. PD - 1902 REVISION: B 6 5 4 1 2 3 DATE: 03/09/05 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com Notes: 1. Controlling dimensions in millimeters 2. Ref: JEDEC MO-203B/AB 3. Package Outline Exclusive of Mold Flash and Metal Burr DESCRIPTION: 6-Pin, SC70 PACKAGE CODE: C Note: For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php All trademarks are property of their respective owners. 8 09-0001 www.pericom.com PS8553C 10/26/09 PI5A4599A SOTiny™ Low Resistance, Low -Voltage Single-Supply SPDT Switch Packaging Mechanical: 6-Pin SOT23 (T) DATE: 10/19/09 DESCRIPTION: 6-pin, Small Outline Transistor Plastic Package (SOT23) PACKAGE CODE: T (T6) REVISION: C DOCUMENT CONTROL #: PD-1912 09-0131 Note: For latest package info, please check: http://www.pericom.com/products/packaging/mechanicals.php Ordering Information Ordering Code Package Code Package Type Top Mark PI5A4599ACEX C Pb-free & Green, 6-pin SC70 ZN PI5A4599ATX T 6-pin SOT23 ZN PI5A4599ATEX T Pb-free & Green, 6-pin SOT23 ZN 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. "E" denotes Pb-free and Green 3. Adding an "X" at the end of the ordering code denotes tape and reel packaging Pericom Semiconductor Corporation • 1-800-435-2336 All trademarks are property of their respective owners. 9 09-0001 www.pericom.com PS8553C 10/26/09