PI3A4626 3.0V, SOTiny™ Single-Supply 0.4Ω SPST (NO) CMOS Analog Switch Features Description • Low On-Resistance: 0.4Ω Max (+2.7V Supply) PI3A4626 is a single-pole/single-throw (SPST) normally open (NO) analog switch that operates from a single +1.5V to +3.6V supply. • 0.1Ω Max. On-Resistance Flatness at +25°C • Fast Switching: 10ns Max. The switch has 0.4Ω Max On-Resistance (RON), with 0.1Ω Max RON flatness over the analog signal range when powered from a +3.0V supply. Leakage currents are less than 2nA and fast switching times are less than 10ns. • +1.5V to +3.6V Single-Supply Operation • TTL/CMOS-Logic Compatible • –25dB Off-Isolation at 100kHz To minimize PC board area use, the device is available in the ultra compact TDFN, and the small compact SOT-23 packages. • 1nA Max. Off-Leakage at +25°C • Packaging (Pb-free & Green available): – 5-pin Small Compact SOT-23 (T) – 6-pin TDFN (ZC) Block Diagrams/Pin Configurations Top Views Applications • Cellular Phones • Communications Circuits COM 1 5 VCC • Battery-Operated Equipment • DSL Modems NO 2 • Audio and Video Signal Routing • PCMCIA Cards GND 3 4 IN SOT23 Pin Description TDFN SOT-23 Name Function 1 1 COM 2 2 NO 3 3 GND 4 4 IN 6 5 VCC Positive Supply Voltage 5 - N.C. No Internal Connection Analog Switch, Common Analog Switch, Normally Open COM 1 6 VCC NO 2 5 N.C. Ground Digital Control Input GND 3 Note: 1. NO and COM pins are identical and interchangeable. Any pin may be considered as an input or an output; signals pass. 4 IN TDFN N.C. = No Internal Connection Switches shown for Logic “0” input Truth Table Input Switch State LOW OFF HIGH ON 1 PS8714A 06/27/04 PI3A4626 3.0V, SOTiny™ Single-Supply 0.4Ω SPST (NO) CMOS Analog Switch Absolute Maximum Ratings Thermal Information Voltages Referenced to GND VCC ...................................................................... –0.5V to +3.6V Continuous Power Dissipation SOT-23 (derate 7.1mW/ºC above +70ºC) ........................... 0.5W VIN, VCOM, VNC, VNO (1) ............................ –0.5V to VCC +0.3V or 30mA, whichever occurs first Current (any terminal)..................................................... ±200mA Peak Current, COM, NO, NC (Pulsed at 1ms, 10% duty cycle)..................................... ±400mA Storage Temperature ........................................ –65ºC to +150ºC Lead Temperature (soldering, 10s) ................................. +300ºC Note: 1. Signals on NC, NO, COM, or IN exceeding VCC or GND are clamped by internal diodes. Limit forward diode current to 30mA. Caution: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Electrical Specifications - Single +3.3V Supply (VCC = +3.3V ± 10%, GND = 0V, VIH = 1.4V, VIL = 0.5V) Description Parameters Test Conditions Package Temp.(°C) Min.(1) Full 0 Typ.(2) Max.(1) Units VCC V Analog Switch Analog Signal Range(3) VANALOG 25 On Resistance RON On-Resistance Match Between Channels(4) On-Resistance Flatness(5) NO or NC Off Leakage Current(6) COM On Leakage Current(6) ∆RON VCC = 2.7V, ICOM = 100mA, VNO or VNC = +1.5V RFLAT(ON) VCC =2.7V ICOM = 100mA, VNO or VNC =0.8V, 2.0V ICOM(OFF) or INC(OFF) VCC =3.3V, VCOM = 0V,VNO or VNC = +2.0V ICOM(ON) VCC =3.3V, VCOM = +2.0V, VNO or VNC = + 2.0V SOT23 TDFN 2 0.4 0.5 Full 0.6 25 0.05 Full 0.06 25 0.1 Full 0.1 25 –1 1 Full –20 10 25 –2 2 Full –20 20 PS8714A Ω nA 06/27/04 PI3A4626 3.0V, SOTiny™ Single-Supply 0.4Ω SPST (NO) CMOS Analog Switch Electrical Specifications - Single +3.3V Supply (continued) (VCC = + 3.3V ± 10%, GND = 0V, VIH = 1.4V, VIL = 0.5V) Description Parameters Test Conditions Temp (ºC) Min.(1) Typ.(2) Max.(1) Units Logic Input Input High Voltage VIH Guaranteed logic High Level Full 1.4 Input Low Voltage VIL Guaranteed logic Low Level Input Current with Voltage High IINH VIN = 1.4V, all others = 0.5V –1 1 Input Current with Voltage Low IINL VIN = 0.5V, all other = 1.4V –1 1 tON VCC = 3.3V, VNO or VNC = 2.0V, Figure 1 0.5 V µA Dynamic Turn-On Time Turn-Off Time Charge Injection(3) Off Isolation(7) tOFF Q OIRR NC or NO Capacitance C(OFF) COM Off Capacitance CCOM(OFF) COM On Capacitance CCOM(ON) CL = 1nF, VGEN = 0V, RGEN = 0Ω, Figure 2 25 10 Full 10 25 10 Full 10 25 RL = 50Ω, f = 100KHz, Figure 3 ns 50 pC -25 dB 130 f = 1 MHz, Figure 4 130 f = 1 MHz, Figure 4 pF 270 Supply Power Supply Range VCC Positve Supply Current ICC Full VCC = 3.6V, VIN = 0V or VCC 1.5 3.6 V 100 nA Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ΔRON = RON Max. - RON Min. 5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC. 7. Off Isolation = 20log10 [ VCOM / (VNO or VNC) ]. See Figure 3. 3 PS8714A 06/27/04 PI3A4626 3.0V, SOTiny™ Single-Supply 0.4Ω SPST (NO) CMOS Analog Switch Electrical Specifications - Single +2.5V Supply (VCC = +2.5V ± 10%, GND = 0V, VIH = 1.4V, VIL = 0.5V) Description Parameters Test Conditions Temp.(°C) Min.(1) Typ.(2) Max.(1) Units VCC V Analog Switch Analog Signal Range(3) On-Resistance On-Resistance Match Between Channels (4) On-Resistance Flatness(5) VANALOG RON ∆RON RFLAT(ON) 0 VCC = 2.5V, ICOM = –8mA, VNO or VNC = 1.8V VCC = 2.5V, ICOM = –8mA, VNO or VNC = 0.8V, 1.8V 25 0.4 Full 0.4 25 0.05 Full 0.06 25 0.1 Full 0.1 25 10 Full 15 25 10 Full 10 Ω Dynamic Turn-On Time Turn-Off Time Charge Injection(3) tON tOFF Q VCC = 2.5V, VNO or VNC = 1.8V, Figure 1 CL = 1nF, VGEN = 0V, RGEN = 0V, Figure 2 25 42 ns pC Logic Input Input HIGH Voltage VIH Guaranteed logic high level Full 1.4 Input LOW Voltage VIL Guaranteed logic Low level Full Input HIGH Current IINH VIN = 1.4V, all others = 0.5V Full –1 1 Input HIGH Current IINL VIN = 0.5V, all others = 1.4V Full –1 1 0.5 V µA Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ΔRON = RON max. - RON min. 5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured. 4 PS8714A 06/27/04 PI3A4626 3.0V, SOTiny™ Single-Supply 0.4Ω SPST (NO) CMOS Analog Switch Electrical Specifications - Single +1.8V Supply (VCC = +1.8V ± 10%, GND = 0V, VIH = 1.4V, VIL = 0.5V) Description Parameters Test Conditions Temp.(°C) Min.(1) Typ.(2) Max.(1) Units VCC V Analog Switch Analog Signal Range(3) On-Resistance On-Resistance Match Between Channels(4) On-Resistance Flatness(5) VANALOG 0 RON VCC = 1.8V, ICOM = –4mA, VNO or VNC = 1.5V ∆RON VCC = 1.8V, ICOM = –4mA, VNO or VNC = 0.8V,1.5V RFLAT(ON) 25 0.4 Full 0.8 25 0.05 Full 0.06 25 0.4 Full 0.6 25 15 Full 15 25 10 Full 15 Ω Dynamic Turn-On Time Turn-Off Time Charge Injection(3) tON tOFF Q VCC = 1.8V, VNO or VNC = 1.5V, Figure 1 CL = 1nF, VGEN = 0V, RGEN = 0V, Figure 2 25 29 ns pC Logic Input Input HIGH Voltage VIH Guaranteed logic high level Full 1.4 Input LOW Voltage VIL Guaranteed logic Low level Full Input HIGH Current IINH VIN = 1.4V, all others = 0.5V Full –1 1 Input HIGH Current IINL VIN = 0.5V, all others = 1.4V Full –1 1 0.5 V µA Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ΔRON = RON max. - RON min. 5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured. 5 PS8714A 06/27/04 PI3A4626 3.0V, SOTiny™ Single-Supply 0.4Ω SPST (NO) CMOS Analog Switch Test Circuits/Timing Diagrams VCC Switch +3V* Input VCC NO COM RL 50ohm IN Logic Input VOUT CL 35pF GND Logic VINH Input VINL Switch Output tr <20ns tf <20ns 50% tOFF VOUT 90% 90% 0V tON LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES THAT HAVE OPPOSITE LOGIC * 1.5V FOR 3.3V SUPPLY CL INCLUDES FIXTURE AND STRAY CAPACITANCE RL VOUT = VNO R L + R ON ( ) Figure 1. Switching Time VCC COM VGEN VCC NO VOUT CL 1nF .1µF ∆VOUT VOUT IN OFF OFF ON IN GND Logic Input IN OFF ON OFF Q = (∆VOUT)(CL) Figure 2. Charge Injection 10nF +3.3V +3.3V 10nF VCC COM COM IN 50Ω Analyzer 50Ω NO VCC IN 0V to 2.4V or 0V to 2V 0V to 2.4V or 0V to 2V Capacitance Meter f = 1 MHz GND NO GND Figure 3. Off Isolation Figure 4. Channel On/Off Capacitance 6 PS8714A 06/27/04 PI3A4626 3.0V, SOTiny™ Single-Supply 0.4Ω SPST (NO) CMOS Analog Switch Packaging Mechanical: 5-Pin SOT-23 (T) .075 1.90� BSC 5 4 .059 1.50 .068 1.75 1 2 .037 0.95 BSC .102 2.60 .118�3.00 0º - 10º 3 Datum "A" .004 0.10 .023 0.60 .014 0.35 .019 0.50� X.XX DENOTES DIMENSIONS X.XX IN MILIMETERS .110 2.80 .118 3.00 .057 1.45�MAX. SEATING PLANE .000 0.00 .005 0.15 Packaging Mechanical: 6-Pin TDFN (ZC) 2.00 ± 0.10 0.65 BSC 0.80 MAX. 2.00 ± 0.10 0.40 ± 0.10 0.20 REF. 0.0 - 0.05 2.30 ± 0.10 1.40 ± 0.10 2.30 ± 0.10 0.90 ± 0.10 0.30 ± 0.05 0.80 MAX. Pin #1 Pin #1 0.0 - 0.05 7 PS8714A 06/27/04 PI3A4626 3.0V, SOTiny™ Single-Supply 0.4Ω SPST (NO) CMOS Analog Switch Ordering Information Ordering Code Packaging Code Package Description Top Mark PI3A4626TX T 5-pin Small Compact SOT-23 ZD PI3A4626TEX T Pb-free & Green, 5-pin Small Compact SOT-23 ZD PI3A4626ZCEX ZC Pb-free & Green, 6-pin Ultra Compact TDFN ZD Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. X = Tape/Reel 3. Number of transistors = TBD Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 8 PS8714A 06/27/04