TM Application Specific Crystal Oscillator 5.0 x 3.2mm PD10GE156 3.3V PECL Low Jitter 156.25MHz 10GbE XO ASSP XO™ for Networking 5.0 x 3.2mm Ceramic SMD Package: Product Features Recommended Land Pattern: • Very low phase jitter • Thicker crystal for improved reliability • Pb-free & RoHS compliant • Industrial temperature range Product Description CREATED USING CADSTD LITE FREEWARE FROM WWW.CADSTD.COM. NON-COMMERCIAL USE ONLY. The PD Series 3.3V, 156.25MHz crystal clock oscillator achieves superb jitter for 10GbE applications. The output clock signal, generated internally with a custom oscillator design, is compatible with LVPECL logic levels. The device, available on tape and reel, is contained in a 5.0 x 3.2mm surface-mount ceramic package. Pin Functions: Applications • 10 Gigabit Ethernet Network Interface Card (NIC) Pin Function 1 OE Function 2 N/C 3 V EE 4 OUT 5 OUT 6 VCC • 10 Gigabit Ethernet Switch/Router • 10 Gigabit Ethernet PHY Module • Serial Attached iSCSI *Extended high frequency power decoupling is recommended (see test circuit for minimum recommendation). To ensure optimal performance, do not route RF traces beneath the CREATED USING CADSTD LITE FREEWARE FROM WWW.CADSTD.COM. NON-COMMERCIAL USE ONLY. package. Part Ordering Information: PD10GE156 SaRonix-eCera™ is a Pericom® Semiconductor company • US: +1-408-435-0800 TW: +886-3-4518888 • www.pericom.com 11-0010 All specifications are subject to change without notice. PD10GE156 Rev D 03/16/11 1 3.3V PECL Low Jitter 156.25 MHz 10GbE XO PD10GE156 TM Application Specific Crystal Oscillator 5.0 x 3.2mm Electrical Performance Parameter Min. Typ. Output Frequency Max. Units 156.25 Supply Voltage 2.97 MHz 3.63 V Supply Current, Output Enabled 80 mA Supply Current, Output Disabled 30 mA 3.30 Frequency Stability Operating Temperature Range ±50 ppm +85 °C VCC – 1.620 V -40 Output Logic 0, VOL Output Logic 1, VOH Notes See Note 1 below V VCC – 1.025 Output Load output requires termination 50Ω to VCC – 2V 55 % Measured 50% waveform Rise and Fall Time Duty Cycle 45 1.0 ns Measured 10/90% of waveform Jitter, Phase RMS (1-σ) 1.0 ps 12 kHz to 20 MHz frequency band Jitter, pk–pk 40 ps 100,000 random periods Notes: 1. Stability includes all combinations of operating temperature, load changes, rated input (supply) voltage changes, initial calibration tolerance (25°C), aging (5 year at 40°C average effective ambient temperature), shock and vibration. 2. For specifications othere than those listed, please contact sales. Output Enable / Disable Function Parameter Min. Input Voltage (pin 1), Output Enable Typ. Max. Units 0.7* VCC Input Voltage (pin 1), Output Disable (low power standby) Output Disable Delay Output Enable Delay or open 0.3* VCC V Outputs disabled to Hi-Z 200 ns 2 Internal Pull Up Resistance Notes V ms 50 kΩ Absolute Maximum Ratings Parameter Storage Temperature Min. Typ. -55 Max. Units +125 °C Notes For the latest product information visit: http://www.pericom.com/products/timing/oscillators/PD10GE156/ For test circuit go to: http://www.pericom.com/pdf/sre/tc_pecl.pdf For soldering reflow profile and reliability test ratings go to: http://www.pericom.com/pdf/sre/reflow.pdf For tape and reel information go to: http://www.pericom.com/pdf/sre/tr_5032_xo.pdf SaRonix-eCera™ is a Pericom® Semiconductor company • US: +1-408-435-0800 TW: +886-3-4518888 • www.pericom.com 11-0010 All specifications are subject to change without notice. PD10GE156 Rev D 03/16/11 2