PERICOM FNEPON125

TM
Application Specific Crystal Oscillator 7.0 x 5.0mm
FNEPON125
3.3V CMOS Low-Jitter 125MHz EPON XO
ASSP XO™ for Networking
7.0 x 5.0mm Ceramic SMD
Package:
Recommended Land Pattern:
Product Features
• Very low phase jitter - 0.5ps RMS
• Thicker crystal for improved reliability
• Low output current - 20mA max.
• Low power stand by mode
• Industrial Temperature Range
• Pb-free & RoHS compliant
Product Description
This is an enhanced high-frequency
3.3V, 125MHz crystal clock oscillator with
superb jitter and low operating current for
Ethernet Passive Optical Network (EPON)
applications.
Pin Functions:
The output clock signal, generated internally
with a patented oscillator design, is
compatible with LVCMOS logic levels.
Pin
Function
1
OE Function
2
Ground
3
Clock Output
4
V DD
Applications
• EPON Optical Network Unit (ONU)
• EPON Optical Line Termination (OLT)
• EPON Gateway
*Extended high frequency power decoupling is recommended (see test circuit for minimum
recommendation). To ensure optimal performance, do not route RF traces beneath the
package.
Part Ordering Information:
FNEPON125
SaRonix-eCera™ is a Pericom® Semiconductor company
•
US: +1-408-435-0800 TW: +886-3-4518888 • www.pericom.com
10-0020
All specifications are subject to change without notice.
FNEPON125 Rev C
04/09/10
1
3.3V CMOS Low-Jitter 125MHz EPON XO FNEPON125
TM
Application Specific Crystal Oscillator 7.0 x 5.0mm
Electrical Performance
Parameter
Min.
Typ.
Output Frequency
Max.
Units
125
Supply Voltage
2.97
MHz
3.63
V
Supply Current, Output Enabled
20
mA
Supply Current, Output Disabled
10
µA
3.3
Frequency Stability
Operating Temperature Range
±50
ppm
+70
°C
10% V DD
V
-20
Output Logic 0, VOL
Output Logic 1, VOH
90% V DD
15
45
Rise and Fall Time
Jitter, Phase RMS (1-σ)
See Note 1 below
V
Output Load
Duty Cycle
Notes
0.25
Jitter, pk-pk
pF
55
%
Measured 50% V DD
3
ns
Measured 20/80% of waveform
0.5
ps
12kHz to 20 MHz frequency band
30
ps
100.000 random periods
Notes:
1. Stability includes all combinations of operating temperature, load changes, rated input (supply) voltage changes, initial calibration tolerance (25°C),
aging (1 year at 25°C average effective ambient temperature), shock and vibration.
2. For specifications othere than those listed, please contact sales.
Output Enable / Disable Function
Parameter
Min.
Input Voltage (pin 1), Output Enable
Typ.
Max.
Units
0.7 V DD
Input Voltage (pin 1), Output Disable (low power standby)
0.3 V DD
Internal Pullup Resistance
30
Notes
V
or open
V
Output is Hi-Z
kΩ
Output Disable Delay
200
ns
Output Enable Delay
2
ms
Absolute Maximum Ratings
Parameter
Storage Temperature
Min.
Typ.
-55
Max.
Units
+125
°C
Notes
For the latest product information visit: http://www.pericom.com/products/timing/oscillators/FNEPON125/
For test circuit go to: http://www.pericom.com/pdf/sre/tc_hcmos.pdf
For soldering reflow profile and reliability test ratings go to: http://www.pericom.com/pdf/sre/reflow.pdf
For typical phase noise go to: http://www.pericom.com/pdf/sre/pn_FNEPON125.pdf
For tape and reel information go to: http://www.pericom.com/pdf/sre/tr_7050.pdf
SaRonix-eCera™ is a Pericom® Semiconductor company
•
US: +1-408-435-0800 TW: +886-3-4518888 • www.pericom.com
10-0020
All specifications are subject to change without notice.
FNEPON125 Rev C
04/09/10
2