ASSP VCXO Application Specific Voltage Controlled Crystal Oscillator 7.0 x 5.0mm PRBST1122 3.3V PECL 122.88MHz Base Station VCXO ASSP VCXO™ 7.0 x 5.0mm Ceramic SMD for Base Station Package: Product Features Recommended Land Pattern: • Very low Pk to Pk jitter - 50ps Max • Low supply current - 90mA Max • Low power standby mode • RoHS Compliant Product Description CREATED USING CADSTD LITE FREEWARE FROM WWW.CADSTD.COM. NON-COMMERCIAL USE ONLY. This is an enhanced 3.3V, 122.88MHz with superb jitter and low operating current for providing clock references in base station applications. Pin Functions: Applications • Base Station Pin Function 1 Voltage Control 2 Enable/Disable 3 Ground 4 Output 5 Output 6 VCC CREATED USING CADSTD LITE FREEWARE FROM WWW.CADSTD.COM. NON-COMMERCIAL USE ONLY. *Extended high frequency power decoupling is recommended (see test circuit for minimum recommendation). To ensure optimal performance, do not route RF traces beneath the package. Part Ordering Information: PRBST1122 SaRonix-eCera™ is a Pericom® Semiconductor company • US: +1-408-435-0800 TW: +886-3-4518888 • www.pericom.com 11-0008 All specifications are subject to change without notice. PRBST1122 Rev 04 02/25/11 1 3.3V PECL 122.88MHz Base Station VCXO PRBST1122 ASSP VCXO Application Specific Voltage Controlled Crystal Oscillator 7.0 x 5.0mm Electrical Performance Parameter Min. Typ. Output Frequency Max. Units 122.880 Supply Voltage VCC 3.135 3.3 Supply Current, Output Enabled Frequency Stability Operating Temperature Range -40 Output Logic 0, VOL 3.465 V 90 mA ±50 ppm +85 °C VCC - 1.62 V VCC - 1.025 Output Logic 1, VOH See Note 1 below V Output Load 50 Duty Cycle Notes MHz From outputs to VCC -2V DC ohms 45 Measured 50% VCC 55 % Rise and Fall Time 5 ns Measured 20/80% of waveform Jitter, Phase 1 ps, RMS(1-s) 12kHz~20MHz Frequency Band Jitter, Peak to Peak 40 ps, Pk-Pk 100.000 Random Periods Phase Noise -65 -50 dBc/Hz At 10Hz offset Phase Noise -90 -85 dBc/Hz At 100Hz offset Phase Noise -120 -115 dBc/Hz At 1kHz offset Phase Noise -130 -125 dBc/Hz At 10kHz offset Phase Noise -135 -130 dBc/Hz At 100kHz offset Notes: 1. Stability includes all combinations of operating temperature, load changes, rated input (supply) voltage changes, initial calibration tolerance (25°C), aging (5 years at +40°C average effective ambient temperature), shock and vibration. 2. For specifications other than those listed, please contact sales. Voltage Control Function Max. Units Pullability Parameter Min. ±80 ± 140 ppm Control Voltage Range 0.3 3.0 V V For RMT Nominal Frequency 10 % Positive Transfer Slope kΩ Control Voltage Pin Center Control Voltage Typ. 1.65 Monotonic Linearity Input Impedance 130 Notes As rated Output Enable / Disable Function Parameter Min. Typ. Input Voltage (pin 2), Output Enable Input Voltage (pin 2), Output Disable (low power standby) Max. Units VOL V or open V Output is Hi-Z VOH Notes Absolute Maximum Ratings Parameter Storage Temperature Min. Typ. -55 Max. Units +125 °C Notes For the latest product information visit: http://www.pericom.com/products/timing/oscillators/PRBST1122/ For test circuit go to: http://www.pericom.com/pdf/sre/tc_vc_pecl.pdf For soldering reflow profile and reliability test ratings go to: http://www.pericom.com/pdf/sre/reflow.pdf For tape and reel information go to: http://www.pericom.com/pdf/sre/tr_7050_xo.pdf SaRonix-eCera™ is a Pericom® Semiconductor company • US: +1-408-435-0800 TW: +886-3-4518888 • www.pericom.com 11-0008 All specifications are subject to change without notice. PRBST1122 Rev 04 02/25/11 2