PI90LV032A PI90LV028A PI90LV018A 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 3V LVDS High-Speed Differential Line Receivers Features • • • • • • • • • • • Signaling Rates >400Mbps (200 MHz) Single 3.3V Power Supply Design Accepts ±350mV (typical) Differential Swing Maximum Differential Skew of 0.35ns Maximum Propagation Delay of 3.3ns Low Voltage TTL (LVTTL) Outputs Industrial Temperature Operating Range: -40°C to 85°C Open, Short, and Terminated Fail Safe Meets or Exceeds IEEE 1596.3 SCI Standard Meets or Exceeds ANSI/TIA/EIA-644 LVDS Standard Packaging (Pb-free & Green avaliable): - SOIC, TSSOP, and MSOP Description The PI90LV032A, PI90LV028A, and PI90LV018A are differential line receivers that use low-voltage differential signaling (LVDS) to support data rates in excess of 400 Mbps. These products are designed for applications requiring high-speed, low-power consumption and low noise generation. A differential input signal (350mV) is translated by the device to 3V CMOS output level. Exclusive to the PI90LV032A quad receiver is a power-down mode that Three-states the outputs and places the device in a lowpower idle state (40mW typical). PI90LV032A RIN1+ + RIN1RIN1+ ROUT1 EN ROUT2 RIN2+ RIN2GND 1 2 3 4 5 6 7 8 16 15 14 16-Pin 13 W, L 12 11 10 9 VCC RIN4RIN4+ ROUT4 EN* ROUT3 RIN3+ RIN3- ROUT1 R1 RIN1- - RIN2+ + ROUT2 R2 RIN2- - RIN3+ + ROUT3 R3 RIN3- - RIN4+ + RIN4- - R4 ROUT4 EN EN* PI90LV028A RIN1- 1 8 VCC RIN1+ 2 8-Pin 7 ROUT1 RIN2+ 3 W,U 6 ROUT2 RIN2- 4 5 GND RIN1+ RIN1RIN2+ RIN2- + R1 - + R2 - ROUT1 ROUT2 PI90LV018A RIN1RIN1+ 1 2 8-Pin W,U Applications NC 3 Applications include point-to-point and multidrop baseband data transmission over controlled impedance media of approximately 100 Ohms. The transmission media can be printed circuit board traces, backplanes, or cables. NC 4 8 VCC 7 ROUT1 6 NC 5 GND RIN1+ RIN1- + R1 - ROUT1 The PI90LV032A, PI90LV028A, PI90LV018A and companion line drivers (PI90LV031A, PI90LV027A, and PI90LV017A) provide new alternatives to RS-232, PECL, and ECL devices for high-speed, point-to-point interface applications. 08-0295 1 PS8423D 11/11/08 PI90LV032A/PI90LV028A/PI90LV018A 3V LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Function Tables PI90LV032A Pin Descriptions Enable s Inputs Output Name De s cription EN EN* RIN+ RIN– ROUT ROUT TTL/CMOS receiver output pins H X H L H RIN+ Non- inverting receiver input pins H X L H L RIN- Inverting receiver input pins X L H L H GND Ground pin X L L H L VCC Positive power supply pin, +3.3V ±10% L H X X Z PI90LV028A Absolute Maximum Ratings (see Note 1, Page 4) Inputs Output Supply Voltage (VCC) .................................... –0.3V to +4.0V RIN+ RIN- ROUT Input Voltage (RIN+, RIN-) ............................ –0.3V to +3.9V H L H Enable Input Voltage (EN, EN*) ......... –0.3V to (VCC +0.3V) L H L Output Voltage (ROUT) ....................... –0.3V to (VCC +0.3V) S Package ................................................................... 750mW Derate S Package ............................. 8.2mW/°C above +25°C PI90LV018A Inputs Storage Temperature Range ........................ -65°C to +150°C Output Lead Temperature Range Soldering (4s) ................... +260°C RIN+ RIN– ROUT H L H L H L Maximum Junction Temperature .............................. +150°C ESD Rating .................................................................... ≥6kV Note: Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Recommended Operating Conditions M in. Typ. M ax. Units Supply Voltage (VCC) +3.0 +3.3 +3.6 V Receiver Input Voltage GND Operating Free Air Temperature (TA) 08-0295 - 40 +3.0 +25 +85 °C 2 PS8423D 11/11/08 PI90LV032A/PI90LV028A/PI90LV018A 3V LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Electrical Characteristics Over supply voltage and operating temperature ranges, unless otherwise specified. (Note 2) Symbol Parame te r VTH Differential Input High Threshold Conditions Pin M in. Typ. M a x. +20 +100 mV Vcm = +1.2V(12) VTL Differential Input Low Threshold VCMR Common- Mode Voltage Range - 100 VID = 200mV peak- to- peak(5) RIN+, RIN- VIN = +2.8V - 20 0.1 2. 3 - 10 ±1 +10 - 10 ±1 +10 VCC = +3.6 or 0V IIN Input Current VIN = 0V VIN = +3.6V VOH Output High Voltage Units VCC = 0V - 20 V μA +20 IOH = - 0.4mA, VID = +200mV 2.7 3 .0 IOH = - 0.4mA, Input terminated 2.7 3 .0 IOH = - 0.4mA, Input shorted 2.7 3 .0 V ROUT VOL Output Low Voltage IOL = 2mA, VID = - 200mV IOS O utput Short Circuit Current Enabled, Vout = 0V(10) IOZ Output Three- State Current Disabled, VOUT = 0V or VCC VIH Input High Voltage 2.0 VCC VIL Input Low Voltage GND 0.8 V +10 μA II Input Current VIN = 0V or VCC, Other Input = VCC or GND VCL Input Clamp Voltage ICL = - 18mA No Load Supply Current Receivers Enabled ICC No Load Supply Current Receivers Disabled ICCZ 08-0295 EN, EN* EN, EN* = VCC or GND, Inputs Open EN, EN* = 2.4V or 0.5V, Inputs Open EN = GND, EN* = VCC, Inputs Open 3 VCC 0 .1 0.25 - 15 - 48 - 120 mA - 10 ±1 +10 μA - 10 ±1 - 1.5 - 0.8 V 10 15 10 15 7 10 mA PS8423D 11/11/08 PI90LV032A/PI90LV028A/PI90LV018A 3V LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Switching Characteristics Over supply voltage and operating temperature ranges, unless otherwise specified. (Notes 3,4,7,8) Symbol Parame te r Conditions M in. Typ. M ax. tPHLD Differential Propagation Delay High to Low (VCM = 1.2V) 1. 8 4 .7 tPLHD Differential Propagation Delay Low to High (VCM = 1.2V) 1.8 4 .7 tSKD1 Differential Pulse Skew | tPHLD - tPLHD |(6) tSKD2 Differential Channel- to- Channel Skew- same device(7) tSKD3 Differential Part- to- Part Skew(8) tSKD4 Differential Part- to- Part Skew(9) tTLH Rise Time 0.35 1.2 tTHL Fall Time 0.35 1.2 tPHZ Disable Time High to Z 8 12 tPLZ Disable Time Low to Z 6 12 11 17 11 17 CL = 10pF VID = 200mV (Figures 1 & 2) 0 0 .1 0 . 35 0 0 .1 0.5 Units 1.0 1.5 ns tPZH Enable Time Z to High tPZL Enable Time Z to Low tMAX Maximum Operating Frequency(13) RL = 2KΩ CL = 10pF (Figures 3 & 4) All channels switching 2 00 250 MHz Notes: 1. “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. 2. Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground unless otherwise specified. 3. All typicals are given for: VCC = +3.3V, TA = +25°C. 4. Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50Ω, tR and tF (0% to 100%) ≤ 3ns for RIN. 5. The VCMR range is reduced for larger VID. Example : if VID = 400mV, the VCMR is 0.2V to 2.2V. The fail-safe condition with inputs shorted is valid over a common-mode range of 0V to 2.3V. A VID up tp VCC - 0V may be applied to the RIN+ / RIN- inputs with the Common-Mode voltage set to VCC/2. Propagation delay and Differential Pulse skew decrease when VID is increased from 200mV to 400mV. Skew specifications apply for 200mV ≤ VID ≤ 800mV over the common mode range. 6. tskd1 is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel. 7. tSKD2, Channel-to-Channel Skew, is defined as the difference between the propagation delay of one channel and that of the others on the same chip with any event on the inputs. 8. tSKD3, Part-to-Part Skew, is the differential Channel-to-Channel skew of any event between devices. This specification applies to devices at the same VCC,and within 5ºC of each other within the operating temperature range. 9. tSKD4, Part-to-Part Skew, is the differential Channel-to-Channel skew of any event between devices. This specification applies to devices over recommended operating temperature and voltage ranges, and across process distribution. tskd4 is defined as IMax - Mini differential propagation delay. 10. Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only. Only one output should be shorted at a time, do not exceed maximum junction temperature specification. 11. CL includes probe and jig capacitance. 12. VCC is always higher than RIN+ and RIN- voltage. RIN- and RIN+ are allowed to have a voltage range -0.2V to VCC- VID/2. However, to be compliant with AC specifications, the common voltage range 0.1V to 2.3V. 13. fmax generator input conditions: tR = tF < 1ns, (0% to 100%), 50% duty cycle, differential (1.05V to1.35V peak to peak). Output Criteria: duty cycle = 60%/40%, VOL (max 0.4V), VOH (min 2.7V), Load = 10pF (stray plus probes). 08-0295 4 PS8423D 11/11/08 PI90LV032A/PI90LV028A/PI90LV018A 3V LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Parameter Measurement Information RIN+ Generator ROUT R RIN- CL 507 507 Receiver ENABLED Figure 1. Receiver Propagation Delay and Transition Time Test Circuit RIN- +1.3V VID = 200mV 0V (Differential) RIN+ tPLHD +1.1V tPHLD 80% ROUT +1.2V 80% 1.5V 1.5V 20% 20% VOL tTHL tTLH Figure 2. Receiver Propagation Delay and Transition Time Waveforms VCC CL includes load and test jig capacitance. S1 = VCC for TPZL, and TPLZ measurements S1= GND for tPZH and tPHZ measurements S1 RL EN RIN+ RIN- Generator DEVICE UNDER TEST CL 50: EN* ROUT 1/4 PI90LV032 Figure 3. Receiver Three-STATE Delay Test Circuit 08-0295 5 PS8423D 11/11/08 PI90LV032A/PI90LV028A/PI90LV018A 3V LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 EN When EN* = VCC 3V 1.5V 1.5V 0V EN* When EN = GND tPHZ Output When VID = +100mV 0V tPZL tPLZ Output When VID = -100mV 3V 1.5V 1.5V 50% 0.5V tPZH 0.5V 50% VCC VOL VOH GND Figure 4. Receiver Three-STATE Delay Waveforms Enable Balanced System Data Input RT 100: 1/4PI90LV032A + Data Output - ANY LVDS DRIVER Figure 5. Point-to-Point Application 08-0295 6 PS8423D 11/11/08 PI90LV032A/PI90LV028A/PI90LV018A 3V LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 16-Pin SOIC (150 Mil) - W 16 3.78 3.99 .149 .157 .0099 .0196 0.25 x 45˚ 0.50 1 .0075 .0098 0-8˚ .386 .393 9.80 10.00 0.41 1.27 1.35 1.75 .053 .068 .0155 .0260 0.393 0.660 REF .016 .050 .2284 .2440 5.80 6.20 SEATING PLANE .050 BSC 1.27 0.19 0.25 .0040 0.10 .0098 0.25 .013 .020 0.330 0.508 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Packaging Mechanical: 8-Pin SOIC (150 Mil) - W 8 .149 .157 3.78 3.99 .0099 .0196 1 .189 .196 .016 .026 0.406 0.660 0.25 x 45° 0.50 .0075 .0098 0-8° 4.80 5.00 0.19 0.25 0.40 .016 1.27 .050 .053 .068 1.35 1.75 SEATING PLANE REF .050 BSC 1.27 .0040 .0098 .2284 .2440 5.80 6.20 0.10 0.25 .013 0.330 .020 0.508 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS 08-0295 7 PS8423D 11/11/08 PI90LV032A/PI90LV028A/PI90LV018A 3V LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 16-Pin TSSOP (4.4mm wide) - L DOCUMENT CONTROL NO. PD - 1310 REVISION: E 16 DATE: 03/09/05 .169 .177 1 1 .0256 BSC 0.65 .193 .201 4.9 5.1 .007 .012 4.3 4.5 .004 .008 .047 max. 1.20 .002 .006 0.09 0.20 0.45 .018 0.75 .030 SEATING PLANE .252 BSC 6.4 0.05 0.15 0.19 0.30 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 • www.pericom.com Note: 1. Package Outline Exclusive of Mold Flash and Metal Burr 2. Controlling dimentions in millimeters 3. Ref: JEDEC MO-153F/AB DESCRIPTION: 16-Pin, 173-Mil Wide, TSSOP PACKAGE CODE: L 08-0295 8 PS8423D 11/11/08 PI90LV032A/PI90LV028A/PI90LV018A 3V LVDS High-Speed Differential Line Receivers 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Packaging Mechanical: 8-Pin Mini Small Outline (MSOP) - U -AX 0$ 2%6)3)/.% $!4% 'AUGE 0LANE $/#5-%.4#/.42/,./ -AX 2%& $ETAIL! $ETAIL! -!8 -!8 3HULFRP6HPLFRQGXFWRU&RUSRUDWLRQ 1VW6WUHHW6DQ-RVH&$ ZZZSHULFRPFRP .OTES #ONTROLLING$IMENSIONSIN-ILLIMETERS 2EF*%$%#-/%!! $%3#2)04)/.0IN-INI3MALL/UTLINE0ACKAGE-3/0 0!#+!'%#/$%5 Ordering Information Ordering Code Package Code Package Description PI90LV032AWE W Pb-free & Green, 16-pin SOIC PI90LV032ALE L Pb-free & Green, 16-pin TSSOP PI90LV028AWE W Pb-free & Green, 8-pin SOIC PI90LV028AUE U Pb-free & Green, 8-pin MSOP PI90LV018AWE W Pb-free & Green, 8-pin SOIC PI90LV018AUE U Pb-free & Green, 8-pin MSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 08-0295 9 PS8423D 11/11/08